MYK2011_100 Low Power Wi-Fi Module User Manual MYK2011_100 Low Power Wi-Fi Module User Manual V 1.9 Overview of Characteristic Support IEEE802.
MYK2011_100 Low Power Wi-Fi Module User Manual TABLE OF CONTENTS LIST OF FIGURES ...................................................................................................................................3 LIST OF TABLES ....................................................................................................................................4 1. PRODUCT OVERVIEW ................................................................................................................5 1.1. 1.1.
MYK2011_100 Low Power Wi-Fi Module User Manual LIST OF FIGURES Figure 1. MYK2011_100 View ...............................................................................................................7 Figure 2. MYK2011_100 Pins Map........................................................................................................7 Figure 3. MYK2011_100 Mechanical Dimension ................................................................................11 Figure 4. MYK2011_100 PCB Symbol Size .
MYK2011_100 Low Power Wi-Fi Module User Manual LIST OF TABLES Table 1 MYK2011_100 Module Technical Specifications .....................................................................6 Table 2 MYK2011_100 Pins Definition..................................................................................................7 Table 3 MYK2011_100 External Antenna Parameters .......................................................................12 Table 11 Reflow Soldering Parameter ...........................
MYK2011_100 Low Power Wi-Fi Module User Manual 1. PRODUCT OVERVIEW 1.1. General Description TheMYK2011_100 is a fully self-contained small form-factor, single stream, 802.11b/g/n Wi-Fi module, which provide a wireless interface to any equipment with a Serial/SPI interface for data transfer.
MYK2011_100 Low Power Wi-Fi Module User Manual 1.1.2 Device Paremeters Table 1 Class MYK2011_100 Module Technical Specifications Item Parameters Certification Wireless standard Frequency range TBD 802.11 b/g/n 2.412GHz-2.462GHz 802.11b: +16 +/-2dBm (@11Mbps) 802.11g: +14 +/-2dBm (@54Mbps) 802.11n: +13 +/-2dBm (@HT20 , MCS7) 802.11n: +13 +/-2dBm (@HT40 , MCS7) 802.11b: -93 dBm (@11Mbps ,CCK) 802.11g: -85 dBm (@54Mbps, OFDM) 802.11n: -82 dBm (@HT20, MCS7) 802.
MYK2011_100 Low Power Wi-Fi Module User Manual 1.2. Hardware Introduction Figure 1. 1.2.1. Pins Definition Figure 2. Table 2 Pin 1,17,32,48 2 MYK2011_100 View MYK2011_100 Pins Map MYK2011_100 Pins Definition Describtion Net Name Comments GND Signal Type Power Ground Debug Pin SWCLK I, PD Debug functional pin, Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.
MYK2011_100 Low Power Wi-Fi Module User Manual Pin Describtion Net Name 3 NC 4 NC 5 Debug Pin 6 SWD Signal Type Comments No connect if not use. I/O,PU N.C No connect 7 GPIO/AD Sleep_RQ I.PU GPIO7, No connect if not use. 8 GPIO/AD Sleep_ON O GPIO8, No connect if not use. 9 +3.3V Power DVDD Power 10 N.C No connect 11 PWM/GPIO/AD PWM_1 I/O GPIO11, No connect if not use. 12 PWM/GPIO/AD PWM_2 I/O GPIO12, No connect if not use.
MYK2011_100 Low Power Wi-Fi Module User Manual Pin Describtion Net Name Signal Type Comments No connect if not use.; 45 Multi-Function nReload 46 I,PU Detailed functions see No connect I,PU “Low” effective reset input. N.C 47 Module Reset EXT_RESETn nReload Pin (Button) function: 1. When this pin is set to “low” during module boot up, the module will enter wireless firmware and config upgrade mode. This mode is used for customer manufacture.
MYK2011_100 Low Power Wi-Fi Module User Manual Supply current, IEEE PS DTIM=100ms Output high voltage Sourcing 6mA Output low voltage Sinking 6mA Input high voltage 12 mA 2.8 V 0.2 2.2 V Input low voltage 0.8 GPIO Input pull-up resistor 200 GPIO Input pull-down resistor 200 Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.
MYK2011_100 Low Power Wi-Fi Module User Manual 1.2.3. Mechanical Size MYK2011_100 modules physical size (Unit: mm) as follows: Figure 3. MYK2011_100 Mechanical Dimension MYK2011_100 Module PCB symbol size (mm) as follows: Figure 4. 1.2.4. MYK2011_100 PCB Symbol Size External Antenna MYK2011_100 module supports external antenna(I-PEX or SMA) option for user dedicated application. Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.
MYK2011_100 Low Power Wi-Fi Module User Manual If user select external antenna,MYK2011_100 modules must be connected to the 2.4G antenna according to IEEE 802.11b/g/n standards. The antenna parameters required as follows: Table 3 MYK2011_100 External Antenna Parameters Item Parameters Frequency range 2.4~2.5GHz Impedance VSWR Return Loss Connector Type 50 Ohm 2 (Max) -10dB (Max) I-PEX or populate directly Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.
MYK2011_100 Low Power Wi-Fi Module User Manual 2. PACKAGE INFORMATION 2.1. Recommended Reflow Profile Figure 5. Reflow Soldering Profile Table 11 Reflow Soldering Parameter NO. Item 1 Reflow Time 2 Peak-Temp Temperature (Degree) Time of above 220 Time(Sec) 35~55 sec 260 max Note: 1. Recommend to supply N2 for reflow oven. 2. N2 atmosphere during reflow (O2<300ppm) 2.2. Device Handling Instruction (Module IC SMT Preparation) 1.
MYK2011_100 Low Power Wi-Fi Module User Manual TAPE BOX Size: 340*340*70 mm Size: 340*340*350 mm (inside) Figure 6. Shipping Information Note: 1 tape = 500pcs 1 box = 5 tapes = 5 * 500 pcs = 2500pcs Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.
MYK2011_100 Low Power Wi-Fi Module User Manual 3. OEM/INTEGRATORS INSTALLATION MANUAL Important Notice to OEM integrators 1.This module is limited to OEM installation ONLY. 2. This module is limited to installation in mobile or fixed applications, according to Part 2.1091(b). 3.The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations 4.For FCC Part 15.
MYK2011_100 Low Power Wi-Fi Module User Manual energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
MYK2011_100 Low Power Wi-Fi Module User Manual émetteur. Caution Exposure: This device meets the exemption from the routine evaluation limits in section 2.5 of RSS102 and users can obtain Canadian information on RF exposure and compliance. Le dispositif répond à l'exemption des limites d'évaluation de routine dans la section 2.5 de RSS102 et les utilisateurs peuvent obtenir des renseignements canadiens sur l'exposition aux RF et le respect.