BEDIENUNGSANLEITUNG / OWNER’S MANUAL S E R I E Vers. 1.
DE | INHALTSVERZEICHNIS SICHERHEITSHINWEISE 3 INSTALLATIONSHINWEISE 4 BETRIEBSHINWEISE 6 Funktionen und Bedienelemente 6 Anschlussbeispiel 4-Kanal-Modus: 1 Stereo System (Front) und 1 x Stereo System (Heck) 7 Anschlussbeispiel 2-Kanal-Modus: 2 x Mono Subwoofer gebrückt 8 Anschlussbeispiel 3-Kanal-Modus: Stereo System und 1 x Mono Subwoofer gebrückt TECHNISCHE DATEN & GARANTIEHINWEIS 9 1 10 FEHLERBEHEBUNG 11 THE OWNER’S MANUAL IN ENGLISH STARTS ON PAGE 13 Dieses Symbol weist Sie auf wichtige
SICHERHEITSHINWEISE|DE BITTE BEACHTEN SIE DIE FOLGENDEN HINWEISE VOR INBETRIEBNAHME! DAS VON IHNEN ERWORBENE GERÄT IST NUR FÜR DEN BETRIEB AN EINEM 12-V-BORDNETZ EINES FAHRZEUGS AUSGELEGT. Andernfalls besteht Feuergefahr, die Gefahr eines elektrischen Schlages oder anderer Verletzungen. LAUTSPRECHERKABEL DÜRFEN KEINEN KONTAKT ZUR KAROSSERIE/MASSE HABEN. Andernfalls könnten ernsthafte Schäden an den einzelnen Komponenten und der Fahrzeugelektrik entstehen.
DE | INSTALLATIONSHINWEISE HINWEIS! Bevor Sie mit der Installation des Soundsystems beginnen, trennen Sie unbedingt den Massepol der Fahrzeugbatterie ab, um Kurzschlüsse und Stromschläge zu vermeiden. MECHANISCHE INSTALLATION Achten Sie bei der Installation darauf, dass keine serienmäßig im KFZ vorhandenen Teile wie z.B. Kabel, Bordcomputer, Sicherheitsgurte, Tank oder ähnliche Teile beschädigt bzw.entfernt werden. Vergewissern Sie sich, dass der Verstärker am Montageort genügend Kühlung erhält.
INSTALLATIONSHINWEISE|DE ELEKTRISCHE ANSCHLÜSSE 1 2 3 4 5 VOR DEM ANSCHLIESSEN Für den fachgerechten Anschluss des Soundsystems sind geeignete Kabelsets im Fachhandel erhältlich. Achten Sie beim Kauf auf einen ausreichenden Kabelquerschnitt (mind. 16 qmm), den passenden Sicherungswert sowie auf die Leitfähigkeit der Kabel. Säubern und entfernen Sie vorhandene Rost- und Oxidationsstellen an allen Kontaktpunkten der Batterie und an den Massepunkten.
DE | BETRIEBSHINWEISE FUNKTIONEN UND BEDIENELEMENTE 1 2 3 4 5 6 7 8 9 10 11 1 Der BASS LEVEL CONTROLLER-Anschluss dient zum Anschluss des Kabels der im Lieferumfang enthaltenen Bass-Fernbedienung BLC-TR, mit welcher der Bass-Pegel z.B. vom Fahrersitz aus eingestellt werden kann. Verwenden Sie nur die mitgelieferte Fernbedienung sowie das dazugehörende Kabel. Die Fernbedienung funktioniert nur im LPF/BPF-Modus und nur an Kanal 3/4. Im DUPE-Mode wird auch CH1/2 geregelt.
BETRIEBSHINWEISE | DE ANSCHLUSSBEISPIEL: 4-Kanal-Modus Stereo Front- und Hecksystem Lautsprecher hinten / links 2 – 8 Ohm Lautsprecher hinten / rechts 2 – 8 Ohm Position INPUT: 4 CH Position XOVER MODE: HPF oder FULL RL RR FR FL Position XOVER MODE: HPF oder FULL Lautsprecher vorne / links 2 – 8 Ohm Lautsprecher vorne / rechts 2 – 8 Ohm Cinch-Audiokabel (FL/FR & RL/RR) vom Steuergerät mit LINE IN CH1 / CH2 und CH3 / CH4 des Verstärkers verbinden VERKABELUNG • Verbinden Sie die Ausgänge des Steuer
DE | BETRIEBSHINWEISE ANSCHLUSSBEISPIEL: 2-Kanal-Modus Mono 2 Subwoofer gebrückt BLC-TR Subwoofer 2 4 – 8 Ohm Position INPUT: 4 CH Position XOVER MODE: DUPE L R Position XOVER MODE: LPF/BPF Subwoofer 1 4 – 8 Ohm Cinch-Audiokabel (L/R oder SUB OUT) vom Steuergerät mit dem LINE IN CH3/4 verbinden VERKABELUNG • Verbinden Sie die Ausgänge des Steuergerätes (Radio) mit den Cinch-Eingängen (LINE IN CH 3 und CH 4) des Verstärkers mittels geeigneten hochwertigen Cinch-Audiokabeln.
BETRIEBSHINWEISE | DE ANSCHLUSSBEISPIEL: 3-Kanal-Modus Stereo System & Mono Subwoofer gebrückt BLC-TR Subwoofer 4 – 8 Ohm Position INPUT: 4 CH Position XOVER MODE: HPF oder FULL RL RR FR FL Position XOVER MODE: LPF/BPF Lautsprecher links 2 – 8 Ohm Lautsprecher rechts 2 – 8 Ohm Cinch-Audiokabel (FL/FR & RL/RR) vom Steuergerät mit LINE IN CH1 / CH2 und CH3 / CH4 des Verstärkers verbinden VERKABELUNG • Verbinden Sie die Ausgänge des Steuergerätes (Radio) mit den Cincheingängen (LINE IN) des Verstärke
DE | TECHNISCHE DATEN MODELL TRITON IV Technische Änderungen und Irrtümer vorbehalten! KANÄLE SCHALTUNGSPRINZIP 4 CLASS A/B Analog Für Schäden am Fahrzeug oder Gerätedefekte, hervorgerufen durch Bedienungsfehler des Geräts, können wir keine Haftung übernehmen. AUSGANGSLEISTUNG RMS 13,8 V Watt @ 4 Ohm Watt @ 2 Ohm Watt @ 4 Ohm mono gebrückt 4 x 60 4 x 100 2 x 200 AUSGANGSLEISTUNG MAX.
FEHLERBEHEBUNG |DE Fehler: keine Funktion Ursache: Lösung: 1. Die Stromversorgungskabel sind nicht korrekt angeschlossen. Erneute Überprüfung 2. Die Kabel haben keinen elektrischen und mechanischen Kontakt. Erneute Überprüfung 3. Die Remote-Steuerleitung des Steuergeräts (Autoradio) ist nicht korrekt am Verstärker angeschlossen. Erneute Überprüfung 4. Die Hochpegel-Anschlüsse sind nicht korrekt angeschlossen und AUTO TURN ON ist angeschaltet Beachten Sie S. 5 und S. 10 5.
DE | FEHLERBEHEBUNG HINWEIS! SCHUTZ-SCHALTUNG Im Verstärker sind verschiedene elektronische Schutzsicherungen integriert. Bei Überlastung, Überhitzung, Kurzschluss an den Lautsprechern, aber auch bei zu niederohmigen Betrieb oder mangelhafter Stromversorgung schaltet dieser ab, um größeren Schäden vorzubeugen. Liegt eine der oben genannten Störungen vor, leuchtet die PROTECT LED (rot) auf. Prüfen Sie in diesem Fall alle Anschlüsse auf Fehler, wie. z.B.
TABLE OF CONTENT|ENG SAFETY INSTRUCTIONS 14 INSTALLATION INSTRUCTIONS 15 OPERATIONAL INSTRUCTIONS 17 Features and operational controls 17 Interconnection example 4-Channel-Mode: 1 x Stereo System (Front) and 1 x Stereo System (Rear) 18 Interconnection example 2-Channel-Mode: 2 x Mono Subwoofer bridged 19 Interconnection example 3-Channel-Mode: 1 x Stereo System and 1 x Mono Subwoofer bridged 20 SPECIFICATIONS & WARRANTY DISCLAIMER 21 TROUBLE SHOOTING 22 This symbol adverts you a important
ENG| SAFETY INSTRUCTIONS PLEASE CHECK THE FOLLOWING ADVICES BEFORE THE FIRST OPERATION! THE PURCHASED DEVICE IS ONLY SUITABLE FOR AN OPERATION WITH A 12V ON-BOARD ELECTRICAL SYSTEM OF A VEHICLE. Otherwise fire hazard, risk of injury and electric shock consists. ENSURE THAT THE LOUDSPEAKER CABLES HAVE NO CONTACT WITH THE VEHICLE’S CHASSIS/GROUND. Otherwise serious damages on the components and the electrical system may occur.
INSTALLATION INSTRUCTIONS | ENG REFERENCE NOTE Before you start with the installation of the sound system, disconnect by any means the GROUND connection wire from the battery, to avoid any risk of electric shock and short circuits. MECHANICAL INSTALLATION Avoid any damage removing of the components of the vehicle like wires, cables, board computer, seat belts, gastank or the like. Ensure that chosen location provide sufficient air circulation for the amplifier.
ENG| INSTALLATION INSTRUCTIONS ELECTRICAL INTERCONNECTION 1 2 3 4 5 BEFORE THE CONNECTION For the professional installation of a sound system appropriate wiring kits are available in car audio retailer stores. Attend the sufficient profile section (at least 16 mm2), the suitable fuse rating and the conductivity of the cables when you purchase your wiring kit. Clean and remove rust-streaked and oxidized areas on the contact points of the battery and the ground connection.
OPERATIONAL INSTRUCTIONS|ENG FUNCTIONS AND OPERATIONAL CONTROLS 1 2 3 4 5 6 7 8 9 10 11 1 The BASS LEVEL CONTROLLER port is for the cable of the enclosed bass remote controller. With this bass remote controller, you are able to adjust the bass level e.g. out of the driver’s seat. Please use only the enclosed bass remote controller and cable. The controller works only in LPF/BPF and only on CH3/4. In DUPE mode operation it also works on CH1/2.
ENG|OPERATIONAL INSTRUCTIONS INTERCONNECTION EXAMPLE 4-Channel Mode: 2 x Stereo System (Front & rear) Speaker rear / left 2 – 8 Ohms Speaker rear / right 2 – 8 Ohms Position INPUT: 4 CH Position XOVER MODE: HPF or FULL RL RR FR FL Position XOVER MODE: HPF or FULL Speaker front / left 2 – 8 Ohms Speaker front / right 2 – 8 Ohms Connect the RCA output (FL/FR & RL/RR) of the headunit with LINE IN CH1/2 and CH3/4 of the amplifier INTERCONNECTION • Connect the RCA lineouts of the headunit with the RCA
OPERATIONAL INSTRUCTIONS|ENG INTERCONNECTION EXAMPLE 2-Channel Mode: 2 x Mono Subwoofer bridged BLC-TR Subwoofer 2 4 – 8 Ohms Position INPUT: 4 CH Position XOVER MODE: DUPE L R Position XOVER MODE: LPF/BPF Subwoofer 1 4 – 8 Ohms Connect RCA output (L/R or SUB OUT) of the headunit with the LINE IN CH3/4 of the amplifier INTERCONNECTION • Connect the RCA lineouts of the headunit with the RCA jacks LINE IN CH 1 and CH 2 of the amplifier with appropriate high-value RCA cables.
ENG|OPERATIONAL INSTRUCTIONS EXAMPLE 3-Channel Mode: 1 x Stereo System & 1 x Mono Subwoofer bridged Subwoofer 4 – 8 Ohms BLC-TR Position INPUT: 4 CH Position XOVER MODE: HPF or FULL RL RR FR FL Position XOVER MODE: LPF/BPF Speaker left 2 – 8 Ohms Speaker right 2 – 8 Ohms Connect the RCA outputs (FL/FR & RL/RR) of the headunit withthe LINE IN CH1 / CH2 and CH3 / CH4 of the amplifier INTERCONNECTION • Connect the RCA lineouts of the headunit with the RCA jacks LINE IN of the amplifier with appropri
SPECIFICATIONS |ENG MODEL TRITON IV CHANNELS CIRCUIT 4 CLASS A/B Analog OUTPUT POWER RMS 13,8 V Watts @ 4 Ohms Watts @ 2 Ohms Watts @ 4 Ohms mono bridged 4 x 60 4 x 100 2 x 200 OUTPUT POWER MAX. 13,8 V Watts @ 4 Ohms Watts @ 2 Ohms Watts @ 4 Ohms mono bridged 4 x 120 4 x 200 2 x 400 Frequency Range –3dB Damping Factor Signal-to-Noise Ratio Channel Separation THD&N Input Sensitivity Input Impedance 20Hz - 30 kHz > 1000 > 90 dB > 60 dB 0,05% 6 - 0.
ENG|TROUBLE SHOOTING Malfunction: no function Reason: Remedy: 1. The power supply connection of the device is not correct. Recheck 2. The cables have no mechanical or electrical contact. Recheck 3. The remote turn-on connection from the headunit to the amplifier is not correct. Recheck 4. The high level inputs (from the head unit) are not connected correct and AUTO TURN ON is activated. See page 16 and 21 5.
TROUBLE SHOOTING|ENG REFERENCE NOTE PROTECTION CIRCUIT This amplifier owns a protection circuit. If overloading, overheating and shorted loudspeakers, or too low impedance or insufficient power supply is insisted, the amplifier shuts down to prevent serious damage. If one of this disfunctions is detected, the red PROTECT LED lights up. Check in this case all connections to detect short-circuits, faulty connections or overheating. Attend the regarding notes on the previous page.
Audio Design GmbH · www.hifonics.de Am Breilingsweg 3 · D-76709 Kronau (Germany) Tel. +49 (0)7253 - 9465-0 · Fax +49 (0)7253 - 946510 Designed and engineered by Audio Design in Germany. All Rights Reserved.