identiFUEL™ Nozzle Unit Gen 3 Installation Guide (Model N° FNU900)
WEEE Directive RoHS Directive European Union Compliance Conformite Européenne Community) (European 2804 Regulatory Australia Conformance Mark (RCM) Federal Communications Commission FCC ID: SL6-NUC600 IECEx ATEX This equipment model number FNU900 is certified intrinsically safe for operation in Zone 0 for the following environments For gas environments: II 1G Ex ia IIB T4 Gb (Ta = -25°C to +60°C) For Mines susceptible to firedamp: I M1 Ex ia I Ma (Ta = -25°C to +60°C) 2
Contents 1. Safety Instructions ................................................................................................................. 4 Training ..................................................................................................................................... 4 Inspection .................................................................................................................................. 4 Label ...................................................................
1. Safety Instructions • • Read the safety instructions before installation. Make sure you understand the safety instructions before installation. Electrical installations in hazardous areas possess features specially designed to render them suitable for operations in such atmospheres.
Label The label for the apparatus can be found on the underside of the device and contains all applicable information regarding the safety certifications of the device as outlined below: Label Information The FNU900 nozzle unit has the following label affixed to the unit with the following information available. Maintenance The general condition of all apparatus shall be noted, and appropriate remedial measures shall be taken where necessary.
Environmental conditions Electrical apparatus in a hazardous area can be adversely affected by the environmental conditions in which it is used. Some of the key elements to consider are corrosion, ambient temperature, ultraviolet radiation, ingress of water, accumulation of dust or sand, mechanical effects and chemical attack. Installation Maintenance work may be carried out on energized apparatus subject to the conditions detailed below.
2. identiFUEL™ Nozzle Unit Universal Low Frequency RFID Readers & Transmitter to Fit on Fueling Nozzles • Reads vehicle tag and identifies vehicle to the Fuel Management System • Automatic activation and standby mode via Tilt Switch • Supports a range of standard filling nozzles The HID Global identiFUEL™ Fueling Nozzle Unit is a universal, intrinsically safe RFID reader, used for Fueling Management Systems (FMS). The Fueling Nozzle Unit can fit onto a wide variety of standard fuel filling nozzles.
How does it work? 1) The nozzle unit fitted to the filling nozzle reads the 125 kHz passive RFID vehicle tag when the nozzle is inserted into the fuel filler pipe, unit remains asleep until moved at which point it searches for a tag. 2) The nozzle unit then sends the tag info along with unit info every 2.2 seconds (ID, status, etc.) over a 433.92 MHz encrypted proprietary RF data link to the Wireless Controller.
3. Specifications Electronic Base Model Number FNU900 Transmitter Frequency to Wireless Controller 433.92 MHz RFID Reader (scanner) to Operating Freq. range to Vehicle 121-129kHz Max. Distance to Wireless Controller 328 ft. (100 m) Data Format EM4582/HitagS - Bi-Phase/Manchester (modulation) Modulation OOK Data rate 16.7 kbps Duty Cycle 50% Mode of operation Simplex Max RF output power 10 dBm Power Supply 2 x 2.
Certifications FCC, CE, RCM, ATEX, IECEx User Interface Bi-colour indication LED Quantity Per Box 1 pc. Warranty 2 years * Depends on the operational temperatures and number of fueling operations per day. 4. Bracket Options Nozzle Range Nozzle P/N Spout Diameter Rotatable Bracket P/N Static Bracket P/N Elaflex ZVASL1 ER242.1 24.0 mm FNU015-0-0-NN-00 FNU020-0-0-NN-00 Elaflex ZVASL1 ER242.2 24.0 mm FNU015-0-0-NN-00 FNU020-0-0-NN-00 Elaflex ZVASL1 ER242.4 24.
5. Installations Instructions Part List A. Static Bracket (Available in various sizes depending on the nozzle used) B. Base Unit C. 2x M5 Screws D. Backing plate set (2 pieces) E. Front Cover F. 4x M3 Screws G. Top Cover (with magnet for activation) H. 4x M3 Screws (short) Instruction Place the static bracket (A) on the nozzle, preferably as far back as possible while still allowing the backing plate (D) to be fitted behind the static bracket.
6. FNU900 Low frequency Reader & Transmitter Regulatory Regulatory Information US- FCC Warning Statement FCC ID:SL6-NUC600 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Australia/ New Zealand Compliance This product conforms to Australia and New Zealand Radio Requirements. European Union Compliance Conformite Européenne (European Community) The full text of the EU declaration of conformity is available at the following internet address: www.hidglobal/certifications This product operates in the following frequencies: • 432-435 MHz band with an RF output power less than 10dBm e.i.r.
Czech Společnost HID Global tímto prohlašuje, že toto radiové zařízení, číslo modelu FNU900, odpovídá požadavkům směrnice 2014/53/EU. Úplný text EU Prohlášení o shodě je k dispozici na následující internetové adrese: www.hidglobal/certifications Tento výrobek používá následující frekvence: - frekvenční pásmo 432-435 MHz, přičemž výstupní RF výkon je nižší než 10 dBm EIRP Estonian Käesolevaga kinnitab HID Global, et see raadioseadmestik mudelinumbriga FNU900 on vastavuses direktiiviga 2014/53/EL.
French Croatian Hungarian Härmed intygar HID Global att denna radioutrustning modell nummer FNU900 överensstämmer med direktiv 2014/53/EU. Den fullständiga texten med intyg om överensstämmelse för EU finns på följande internetadress: www.hidglobal/certifications Par la présente, HID Global déclare que cet équipement radio Modèle FNU900 est conforme à la directive 2014/53/UE. Le texte intégral de la déclaration de conformité de l'UE est disponible sur le site Internet: www.
