Installation Manual

ManualsBrandsHID Global ManualsElectronics6015

HID Corporation 9292 Jeronimo Road Irvine, CA 92618 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690

Web page, E-mail - www.prox.com AMR100 Property Pass Reader Installation Manual 6015-900 REV A 1 of 6

HID ProxTrak

This de vi ce c ompli es with pa rt 15 of the FCC

may ca us e u nd es ired op era tio n.

inte rfere nc e re ci ev ed, in cl udi ng in terfe ren ce tha t

inte rfere nc e, a nd (2) T his d ev ic e mus t ac c ept an y

con dit ion s: (1) T his d ev ic e may no t c aus e harmful

rules . Ope rati on is s ubj ec t to th e fo ll owin g two

1998 HID CORPORATION

U.S. PATENT NO. 4,7 30 ,18 8 5 ,04 1,6 25

FCC ID: JQ6601 5

ELECTRICAL RATING: 1 0.8 -13. 2VDC/25 0mA

REFER TO OPERATORS MANUAL 601 5-90 0.

ACCESS CONTROL SYSTEM UNIT ACCESSORY.

8T29

LISTED

HID CORPORATION

11.80 1.00

11.80

.156 X .04 DEEP

12 PLACES

0.00

1.64

2.625

4.00

1.64

2.625

4.00

Installation Requirements

The following instructions will explain the installation and

operation procedure for the AMR100 Property Pass

Reader. The instructions include these sections:

Installation Instructions

Mounting Preparation

Cabling Preparation

Mounting

O-Ring

Switch Settings

Jumper Settings

Power Supply

Cover Installation

AMR100 Property Pass Reader

AMR100 Property Pass Reader Installation Manual (6015-900)

Installation Instructions

Mounting Preparation

1. Determine an appropriate mounting position for the

AMR100 Reader.

2. Install an electrical box or drill mounting holes for #6

fasteners. Starter holes for mounting are indicated on

Figure 2.

3. The Reader should be mounted at least 6" away from

any metallic surface 12"x12" or larger. Incidental metal

such as aluminum studs and conduit can be compen-

sated.

Figure 1

Important Product Specifications

Environmental Characteristics

Operating Temperature Range -0

C to 70

C (32

F to 150

Storage Temperature Range -40

C to 85

C (-40

F to 185

Power Requirements

Operating Voltage Range 12.0VDC ± 1.2VDC

Peak Current 12VDC 1.5A

Average Current 1.0A

Excitation Frequency 125KHz ± 1 KHz

Parts List (Included) Quantity

1) AMR100 Property Pass Reader 1

2) O-ring - 12"diameter x .25" thick 1

3) #6-32x.625 Flathead Screw 1

4) Installation Manual 1

5) Front Cover Label 1

6) Strain Relief Nut 2

Parts List (NOT Included)

1) External 12V power supply 1

2) #6 Mounting Screws A/R

3) Cable (See requirements below) A/R

Cabling Requirements

Shielded

Power & Ground - 18AWG- 22AWG

All other signals - 24 AWG minimum

Strain Relief Nut cable range: .19 to .390

Place screw to

secure top cover

here.

Summary of content (6 pages)

PAGE 1
AMR100 Property Pass Reader Installation Manual (6015-900) Installation Requirements Parts List (Included) The following instructions will explain the installation and operation procedure for the AMR100 Property Pass Reader. The instructions include these sections: 1) AMR100 Property Pass Reader 2) O-ring - 12"diameter x .25" thick 3) #6-32x.
PAGE 2
Figure 2 Cable Preparation 1. Route the cable from the AMR100 Reader and/or power supply to the Host. 2. Prepare the cable by cutting the jacket back 2" and strip the wires 1/4". Tinning the wires is not required. 3. Install the cable strain relief nut #1 on the rear of the AMR100 Reader as indicated in Figure 2 . (Strain relief nut #2 is for use with the LCD display unit that is purchased separately.
PAGE 3
Mounting 1. Mount the base of the AMR100 Property Pass Reader to the prepared surface using the starter holes indicated in Figure 2. 2. These holes are not through holes and require drilling before mounting. 3. Choose the holes to be used and drill with a 5/32 (.156) inch bit. Use #6 screws only.
PAGE 4
Switch 3 Hardware settings On 1 MaxiTrak mode * (Must remain in ON position) 2 Access Control Exciter * (Must remain in ON position) 3 Free-Running Acq * ID acquisition is free running; asynchronous with Host polls 4 Staus LED's Disable * (Must remain in ON position) Off 5 Hardware Demodulator * (Must remain in OFF position) 6 Low Gain * (Must remain in OFF position) 7 8 Receivers (Not Used) * (Must remain in OFF position) 8 2nd Access Reader (Not Used) * (Must remain in OFF position) Swi
PAGE 5
Jumpe r B lock Jumpe r s e tting Functional D e s c ription P-5 Ground s e le c t *1-2 Always should be left in this position P-8 +5v s e le c t *1-2 Always should be left in this position 2-3 P-6 Input communication protocol s e le c t 1-2 RS485 serial input s e lected *2-3 RS232 serial input s e lected 1-2 RS485 serial output s e lected 2-3 RS232 serial output s e lected Output path se le c tor P7 #1- P10 #1 S e rial output A se lected Input path se le c tor P7 #2- P10 #2 S e rial i
PAGE 6
Power Supply 1. The AMR100 Property Pass Reader can be operated over the full range of 12VDC to ± 1.2V. A linear supply is recommended. 2. After the Reader and power supply are wired together, apply power to the reader. Cover Installation 1. Place the top cover onto the base of the AMR100 Reader. 2. Secure the cover to the base. Use the flathead screw provided. The location of the top cover screw is indicated on Figure 1. 2. Place the HID label over the screw.