Preface Introduction The introduction is applicable to V90 Plus products. V90 is a new type of GNSS receiver used for measurement. The introduction describes how to install, set and use V90 products. In order to help you better use Hi-Target series products, Hi-Target suggests you carefully reading the instruction. If you are unfamiliar with V90 products, please refer to www.hi-target.com.
Warning: the contents here generally are very important. In case of failing to operate based on warning contents, it will damage the machine, lose the data, break down the system and endanger personal safety. Exclusions Before using the products, please carefully read the operating instruction, and it will help you better use the product. Hi-Target Surveying Instrument Co.
instruction and software & hardware, without eliminating the possibility of deviation. The pictures in operating instruction are only used for reference. In case of inconformity with products, the products shall prevail.
Content Product Introduction ...................................... 6 Preface ............................................... 7 Product Characteristics ............................... 8 Cautions for Use ...................................... 8 Introductions to Receiver ................................ 10 Receiver Appearance .................................. 11 Control Panel ........................................ 11 Upper Cover .......................................... 12 Bottom Cover ...................
Interface ............................................ 44 Function keys and indicators ......................... 44 Physical Characteristics ............................. 44 Environment .......................................... 45 Socket and Main Accessories .............................. 46 Preface .............................................. 47 Five-pin socket ...................................... 47 Five-wire ............................................ 48 Mini USB Interface .........................
HI-TARGET 接收机介绍 CHAPTER 1 Product Introduction This chapter describes: ■ Preface ■ Product characteristics ■ Cautions for use 6
Preface V90Plus is a new type of GNSS receiver used for measurement pushed forward by Hi-Target Brand,used a new design,Magnesium alloy construction,Linux3.2.0 operating system,Combined gravitational acceleration sensor, WiFi connectivity, it is a realization of lightweight, intelligent, easy to use measurement GNSS receiver.
HI-TARGET 接收机介绍 Product Characteristics ◇ A new generation of small intelligent BDS RTK，equipped with top drive core，provided intelligent mapping of the overall solution; ◇ Using multi-satellite and multi-frequency GNSS units，Support BDS, GPS, GLONASS.
In order to guarantee the quality of continuous tracking observation and satellite signals, it is required that the overhead observation station shall be open, without flaky barriers above 15° elevating angle; in order to diminish the interference of electromagnetic wave to GNSS satellite signals, the observation station shall be free form strong electromagnetic wave within the range of 200m, such as television tower, microware station and high-voltage transmission line; in order to avoid or reduce multipat
HI-TARGET 接收机介绍 CHAPTER 2 Introductions to Receiver This chapter describes: ■ Receiver appearance ■ Control panel ■ Upper cover ■ Bottom cover ■ Batteries ■ Environmental requirements ■ Electronic jamming 10
Receiver Appearance The product appearance is divided into three sections，upper cover, bottom cover and control panel. upper cover bottom cover control panel Figure 2-1 Control Panel V90Plus middle frame for the control panel of the receiver, the control panel includes a power switch button, a button to include all the features of V90Plus receiver set. Three indicators, namely satellite lights, power light (bi-color light), light (bi-color light).
HI-TARGET 接收机介绍 Satellite light (green light) status light (red and green light) power light (red and green light) Power Button Functions: Startup,shutdown,operating mode switching, the mode switching confirmation status query, automatically set the base station, forced shutdown, reset the board and so on.
8 1- Screw connection 2- speaker 3-USB interface and protective plug 4-GPRS/ Antenna Interface 5- Five-pin plug socket and protection 6- Battery compartment 7SD card slot 8-SIM card slot 9- Battery Cover 10-SLC Power Block. Figure 2-4 ◇ connection screw: for the instrument fixed to the base or the pole. ◇ Trumpet: Real-time operation and status of the instrument voice broadcast.
HI-TARGET 接收机介绍 ◇ Five-pin socket: For connection to the host and external data links and external power source. ◇ battery compartment: for housing lithium batteries. ◇ SD card slot: SD card for housing, can store large-capacity static data. ◇ SIM card slot: for receiving USIM / SIM card for data link communications and remote control. ◇ Battery cover: battery cover can dust and water, batteries and a host of spare parts have protection role. ◇ SLC power base: lithium is used to connect with the host.
Close Open Figure 2-5 Positive pole Negative pole Figure 2-6 Environmental Requirements The receiver shall operate in dry working environment regardless of waterproof materials.
HI-TARGET 接收机介绍 Electronic Jamming The receiver shall not be installed in the place near to strong electric power and interference signal, such as: ◇ Oil duct (spark plugs) ◇ Generator ◇ Battery-operated motor cycle ◇ DC-AC power supply changeover equipment ◇ Signal transmitting station (tower) ◇ Power supply 16
CHAPTER 3 Elementary Operation This chapter describes: ■ Control panel ■ Function Key ■ Status Inquiry ■ LED Function ■ Start and stop receiver ■ Reset Motherboard ■ Automatic setting station ■ Static collection ■ Static data storage ■ RTK data storage
HI-TARGET ■ U disk data download ■ Firmware ■ Electronic bubble ■ Electronic bubble calibration ■ WiFi password settings ■ Power Supply System ■ Radio frequency settings ■ SIM card / USIM card ■ Micro SD Card 18
Control panel Most settings and operations of receiver are completed using two keys on control panel. Power light Satellite light Status light Figure 3-1 Function Key Table 3.
HI-TARGET Status Inquiry See Schedule Reset Motherboard The boot state, long press the button more than 6 seconds, voice reporting second sound "ding dong", release the button, reset motherboard Forced shutdown The boot state, long press the button more than 8 seconds, forced shutdown Status Inquiry Working status Table 3.
fast flash Tip Power: 1-4 flash per minute under the direction of electricity Signal light Off when you did not use GSM / WiFi client (Status Green) Long-term lighting GSM / WiFi connected to the server Slow flash GSM has landed on the 3G / GPRS network or connect to WiFi hotspots fast flash GSM is landing when prompted 3G / GPRS networks or WiFi hotspots are connected Slow flash 1, the data link transmit and receive data (mobile station to receive only tips, the base station only prompt emissi
HI-TARGET trap power lights on button for previous startup and Voice prompt of data link mode 1 second Shutdo Long All wn press lights off indicator Shutdown music power button for 3 seconds Reset motherboard The boot state, long press the button more than 6 seconds, voice reporting second sound "ding dong", release the button, reset the motherboard.
memory card). After the static data file must be downloaded to a computer for processing a static post-processing software. NOTE：Working mode switch: You can also switch by handheld, please refer to the specific operation "Hi-Survey Software User's Guide" → equipment → Accessibility → static capture settings. Static acquisition step 1. Set up the instrument at the measurement point, the point is to strictly, and leveling. 2.
HI-TARGET 3, the recording name, instrument number, instrument height, began observing time. 4, boot, set the host to the static measurement mode. Satellite Blinking is searching for satellites. Satellite into long bright lights from flashing status indicates locked satellites. Status lights flash once every few seconds, indicating that the acquisition of one epoch. 5, after the measurement is complete shutdown, shutdown time record. 6, download processing data.
figure 3-3 Note：When the receiver inside and outside the storage space is less than 2MB, data light (red state) flash, and will stop recording data, the existing data files will not be overwritten. RTK data storage iHand20 handheld Haida V90Plus receiver can be connected via WiFi, Bluetooth or network, when work began after the setup is complete, the memory card handheld, you can book by hand random configuration data cable data collected RTK RTK data storage downloaded onto your computer.
HI-TARGET For more information about the hand-book, read "Hi-Survey Software User's Guide." U disk data download Receiver file management is stored by USB drive. It can be used upon inserting and download by dragging directly without download programs. It can only download static data and unable to write or read the receiver. The receiver can download USB drive data with Y-type data cable, one end is connected to computer USB and the other end is connected to eight-core socket on bottom of receiver.
Figure 3-6 Note：the static files in removable disk can be deleted by GNSS receiver management software rather than deleting directly. Firmware The receiver uses the 3G network, the host firmware can be automatically upgraded (You can refer to: "Hi-Survey Software User's Guide" → equipment → Accessibility → receiver set) through the network, the user can also choose to manually U disk upgrade.
HI-TARGET corresponding voice prompts to upgrade if the upgrade fails again or contact technicians. Electronic bubble After Hi-Survey in demo mode, the built-in GPS or connect V90Plus, support electronic bubble measuring software interface schematic display electronic bubble position, the user can select the automatic collection in electronic bubble automatic measurement and automatic sampling sites according to the electronic bubble state.
Figure 3-8 Figure 3-9 Electronic bubble calibration When connecting V90Plus receiver, users can calibrate the electronic bubble under the [Accessibility].
HI-TARGET To do the following: [Device] → [Accessibility] → [electronic bubble calibration] Figure 3-11 V90Plus receiver placed outside the strict leveling base remain stationary until the receiver locks satellite, ready when you are ready click on [Start] button to bring up the calibration check box. Keep the instrument in the strict leveling base, do not move, so that the satellite receiver lock. When you are ready click "OK.
Click the pop-up confirmation box OK button, the hosts began to calibrate the electronic bubble. Figure 3-13 Figure 3-14 NOTE：Electronic bubble age calibration period recommended value is set to 30 days, more than the set number of days without calibration, the receiver will not work! WiFi password setting Set V90Plus host as a WiFi hotspot when connected to a password.
HI-TARGET Figure 3-15 Note：1, WiFi factory default password See Schedule 3; 2. If you have forgotten your own set of WiFi password, you can "GNSS receiver management software V1.4.2" → WiFi password, enter the password and click OK to. Specific methods of operation management software receiver, see: Annex 4.
Power Supply System Battery installation and removal Installation 1, the battery cover and push back gently press the metal buckle. Figure 3-16 2, the battery cover up to open the shells.
HI-TARGET Figure 3-17 Open Close 图 3-18 3, toward the end of marked "Close" gently press and push (red arrow) can complete the battery installation. Remove: Along with the name "Open" and hold the direction of launch, pour out the battery,the battery complete uninstall.
Battery, charger table 3.
HI-TARGET Power supply Table 3.6 Power Supply powe r Power supply Lithium batteries; 5-pin external power socket Power range DC power supply: 6 ~ 28V V90Plus receiver can also be powered via 5-pin socket bottom of the main external power supply. GSM mobile station external voltage range DC 6 ~ 28V, current is greater than 3000 mA. When there is an external power supply, the host will automatically detect the lithium battery and external power supply voltage, select high voltage power supply.
Charging BL-5000 rechargeable lithium battery must use a dedicated CL-8410 / CL-4400 lithium battery charger, charging time is about 7 hours. CL-8410 Battery Charger charging indicator light is red during charging, charging is completed the light turns green, continue to charge 1 to 1.5 hours, then the battery is fully charged.
HI-TARGET Close Charge indicator Power Indicator Figure 3-20 2, along the "Close" direction, the red arrow shown in the figure above, push the battery until it clicks. 3. After connecting the power, "charging indicator" is displayed as red light is charging. Caveat ：1. Only use factory configuration of the battery and charger, do not put the fire or short-circuited with a metal electrode.
USIM Card WCDMA（ZHD/VRS） GPRS（ZHD/VRS） GSM SIM Card GPRS（ZHD/VRS） GSM Installation card Use V90Plus Receivers RTK jobs, you need to prepare SIM or USIM card and open the corresponding data communication services. The required number of cards, depending on your system configuration RTK survey. Each host and each handheld for an installation card.
HI-TARGET 2, SIM card slot is consistent with the notch direction. Figure 3-22 3, the SIM card in the deck, the front (with metal contact surface) down into the slot. Figure 3-23 4, the entire SIM card into the slot to complete the installation. Note ： Before installing the card you must turn off the receiver! If the SIM card is installed in the boot state, the receiver will not detect the SIM card, the mode setting is invalid! Micro SD card Micro SD card can store data collection and program files.
buy zone configuration. Ordinary SD card Micro SD card volume by volume to be large to fit V90Plus use. V90Plus largest to 16GB Micro SD card. 2. The iHand20 induction area close V90Plus sensing area, Hi-Survey will automatically start V90Plus Bluetooth connection.
HI-TARGET CHAPTER 4 Technical parameters This chapter describes: ■ GNSS section ■ Receiver Accuracy ■ Interface ■ Function keys and indicators ■ Physical Characteristics ■ Environment 42
GNSS Section ◇ GPS：Synchronous tracking L1 ◇ BDS：Synchronous tracking B1、B2 ◇ GLONASS：Synchronous tracking L1 C/A、L1 P、L2 C/A ◇ SBAS：Synchronous tracking L1 C/A、L5 ◇ GIOVE-A：Synchronous tracking L1 BOC、E5A、E5B E5AltBOC （Optional） ◇ GIOVE-B：Synchronous tracking L1 CBOC、E5A、E5B E5AltBOC （Optional） ◇ GALILEO：（Upgrade Reserved） ◇ Initialization time Typically <10 seconds ◇ Initialization reliability> 99.
HI-TARGET Height：±(15＋1×10-6D) mm Interface ◇ 1 x RS232 serial interface ◇ 1 x Mini USB interface ◇ 1 x SIM card interface ◇ 1 x SD card interface ◇ 1 x 3G / GPRS antenna interface ◇ 1 xBluetooth interface ◇ 1 x WiFi Interface ◇ 1 x Built-in lithium battery Interface ◇ 1 xFifth pin interface Function keys and indicators ◇ 1 panels buttons: a power button on the receiver can be flexibly various settings, and a sound, light work with ◇ 3 LEDs: a satellite LED (monochrome), a status light (color), a power in
◇ Weight: 1.0kg (without lithium battery) ◇ Anti-2 m natural drop, anti-two meters underwater temporary immersion. ◇ Built-in 5000mAh high-capacity lithium-ion battery. Voltage: 7.4V, a new battery continuous working time: 12 hours static, GPRS mode 9 hours, 2W station transmitting 7 hours. ◇ Can be an external DC power supply, wide input range 6 ~ 28V, internal and external power supply automatically switches Host Power (static mode): ≤3.
附表 1 出产默认频率表 CHAPTER 5 Socket and Accessories This chapter describes: ■ Preface ■ Five-pin socket ■ Five-wire ■ Mini USB interface ■ Mini USB wire ■ Antenna Interface ■ Antenna 46 Main
Preface The chapter will introduce the appearance and application of main interface of receiver and accessories. The following equipment does not represent all users purchased V90 Plus. According to different configurations, the specific configuration shall be subject to the delivery order upon purchasing. Five-pin socket Figure 5-1 Figure 5-2 1,Five-pin socket:Also known as COM2/PW2,normally used to connect the host and external data link connection, external power source. Table5.
附表 1 出产默认频率表 2, All the companies are in circular socket counterclockwise positive start numbering pin; pin round plugs are numbered starting with welding face counterclockwise. 3,All the above data (TXD), the (RXD) signals to receivers explained. TXD transmit data to the receiver signal line, RXD received data to a receiver line. 4.
Five-pin socket：For connecting the radio receiver and five-pin plug socket. Plug the red dot Socket red dot Figure 5-4 Mini USB Interface Mini USB intreface Figure 5-5 For connection to the host and external devices, upgrade firmware and download the static data, can also be used as USB to serial port using a special mode of operation (need to install drivers, see Annex 4).
附表 1 出产默认频率表 Standard USB interface Mini USB interface Figure 5-6 Mini USB cable, one end is a standard USB connector on one end and Mini USB interfaces; an external device connected to the host for data transmission. Antenna Interface Antenna Interface Figure 5-7 3G / GPRS radio antenna is built using the same antenna interface; connection 3G / GPRS antenna using the network.
Schedule 2 control panel lights Table 2 control panel lights illustrate Operating Meaning Power light (yellow) on Normal voltage: the battery> 7.6V, foreign> 12.6V Power light (red) on Normal voltage: 7.1V
附录 Schedule 4 USB virtual serial port driver installation 1）First, it confirms that our equipment has been launched USB virtual serial port functions. This step requires the use of the company's Android hand book binding Hi-Survey software to view and set in the "Device" → "Accessibility" → "Receiver Settings" → "USB Virtual Serial Port" → "ON". 2）Check if the function is open, with a Micro USB cable to connect the instrument and computer, install the driver. Win7 32bit system as an example to demonstrate.
4）Open Systems "Device Manager" in the "other" option, you will see two unidentified device. "CDC Serial" and "RNDIS". Figure 2 5）Click "CDC Serial", right-select "Update Driver Software" in the pop-up window, select "Browse my computer for driver software (R)", then select the file drivers "linux_cdc_seial.inf" where the folder directory, then click "Next.
附录 Figure 3 6）If you search for a valid drive, pop occurs.
In this case, select the "Always install driver software." After a successful installation displays the following information. Figure 5 7）Then you can see the serial device, and serial number in the Device Manager.
附录 Figure 6 Since we did not use to "RNDIS" device, so it can not install the driver.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
