Qmini M series industrial GIS data collector instructions
Handbook revision situation Revision date March 2012 Revision number 1 Introduction Qmini M series industrial GIS data collector instructions version 1.
Catalogue Preface.............................................................................................................................................. 1 Chapter 1.......................................................................................................................................... 3 Products overview....................................................................................................................... 3 Product introduction.........................................
Chapter 4........................................................................................................................................ 21 Technology parameters ............................................................................................................. 21 Technology parameters .............................................................................................................
Preface Manual use Welcome to use Qmini M series industrial GIS data collector instructions。 This manual applies to Qmini M1 / Qmini M3 / Qmini MR/Qmini MT/Qmini MP series, this manual introduces how to install, set up and use industry-specific GIS data collector. Manual introduction Qmini M series industrial GIS data collector is a new GPS/GIS data collector, even if you use other types of industrial GIS data collector, please also carefully reading before use this specification.
Responsibility absolution Before you use the product,you should read the introduction carefully. Guangzhou HI-TARGET surveying and mapping instruments Co., LTD. We will not take the responsibility if you not operate within the product instruction。 Guangzhou HI-TARGETsurveying and mapping instruments Co., LTD. Is committed to continuously improve product function and performance, improve the service quality, and keep the right to change the content of the instruction without notice in advance.
Chapter 1 Products overview This chapter introduces ■ Product introduction ■ Product introduction ■ Use and the matters needing attention 3
Product introduction Qmini M series industrial GIS data collector products are equipped with complete navigation and positioning function and GIS data acquisition function, with the operating mode of physical buttons and touch screen, support input in both Chinese and English. The three industrial standard design, and can be dropped from 1.5 meters high to the cementfloor without angthing, dustproof and waterproof standard can adapt to complex work environment in the field.
Use and the matters needing attention Although Qmini series industrial GIS data collector use the corrosion resistance and impact resistance materials, but the instrument still need our careful use and maintenance, and keep it in dry environment as far as possible. In order to improve the stability of the data collector industrial GIS and use cycle, please avoid industrial GIS data collector exposed to extreme environment , such as: damp, high temperature, low temperature, corrosive gas or liquid, etc.
Chapter 2 The introduction of Qmini M series industrial GIS data collector The introduction of this chepter: ■the front of Qmini series industrial GIS data collector ■the back of of Qmini series industrial GIS data collector ■interface ■the appearance of touching pen ■battery ■data line ■ Condole belt This chapter introduces Qmini series industrial GIS data collector appearance, interface, battery, touch pen and data, etc.
The front of Qmini M series industrial data collector The front of Qmini series industrial GIS data collector,Including the touch screen, keyboard, a microphone,protection set ,ect. Chart2-1◊ Touch screen, 3.7 inch vertical screen can be directly click operation, support input in both Chinese and English. ◊ Protective set: prevent grind, prevent fell, shock, effective instrument to avoid scratching. ◊ Keyboard: direction control, the confirmation button, exit button, switch machine etc. Function.
The back of Qmini M series industrial data collector Qmini series industrial GIS data collector on the back of, including the camera, battery, the condole belt hole, horn, etc. camera (with flashfunction) horn the condole belt hole ◊ Camera: built-in digital camera for video information site collected ◊ Battery: the built-in 3.7 V, 3100 mAh lithium batteries ◊ Condole belt hole: connect the strap can prevent slide.
∆ Note: when the horn is in water, it may appear silent or husky, dry it and it will be back to normal. The loudspeaker and the instrument is completely waterproof, horn with water will not affect instrument performance, but please timely drying processes. Interface Qmini M series industrial GIS data collector interface position was identified, its main function is charging and data transmission, installation SD card, etc. Picture2-3 ◇Charging interface: connect the charger for lithium battery charge.
Touching pen Qmini M series industrial GIS data collector with standard touching pen, located in Qmini M series industrial GIS data collector condole belt hang line. Picture2-4 Battery This illustration shows the standard 3100 mAh lithium battery appearance figure. Picture2-5 ▲notice:In order to protect the environment, when the lithium battery failure, do not throw them away, please return to HI-TARGET or professional battery recycling units processing.
Data line Picture2-6 ◇Industrial GIS data collector interface: used in connection Qmini series industrial GIS data collector. ◇USB interface: to connect computer USB port , used for data download. ▲Warning: when the cable is not in use,it should be packed in where the place is not easy to squeeze to prevent damage to the plug.
Chapter 3 Basic operation The introduction of this section: ▇.keyboard ▇ Touching pen ▇.MicroSD ▇.Power ▇.Switch card supply system machine operation ▇.data obtain ▇.
The HI-tARGET Qmini GIS data collector series industrial setting and operation can be most completed by touching pen , the common operation can be completed by the keyboard . Now we will introduce the look and function of the keyboard simply. Keyboard Qmini M series industrial GIS data collector keyboard. The keyboard keys contains: the confirmation button , exit key, F1 function keys, switch machine key and the direction key.
Switch mechanical and electrical source key/backlight control key: more than 3 seconds long press turns on/off the phone. On state, hold the button 1 second, switch a backlight switch. Navigation keys: move the cursor, to change the content change options ▲notice:when temporarily do not need to use Qmini series industrial GIS data collector in work, please close a backlight to save electricity, to extend industrial GIS data collector work time.
Remove the SD card, open the card buckle along the direction of OPEN , remove the SD card,lock the card slot along the LOCK direction . ▲Note: the MicroSD cards (also named TF card) are small volume external flash memory storage expansion CARDS, usually used in mobile phone, PDA, users should distinguish it between the common one. The volume of ordinary SD card are larger than the MicroSD card, not suitable for Qmini M series industrial GIS data collector use.
◊ Qmini M series industrial GIS data collector battery, charger model Table 3-1 Qmini M series industrial GIS data collector battery, charger model name model 3100 mAh lithium batteries BL-3100A Lithium battery charger CL-3100A ◊charge Charge should be used when the instrument with standard special charger or seat charger in certain temperature range charging, and charging time should achieve a certain requirements.
3, if the use time of the battery significantly shortened, please stop using the battery, the battery is aging, please replace new battery. Switch machine operation Data obtain 1 install Microsoft ActiveSync In the incidental CD (tool software \ \ \ ActiveSync connection program), double click MSASYNC45. Exe file,please follow the instructions to complete installation. After the installation, find Microsoft ActiveSync operation inr the "start menu" "program" .
If you have connected them but the computer can't identify, please take the following method to solve: a:close the USB charging in the pow setting model press to the homepage,select”setting”→”power”→”USB charging”,close the control switch of the USB charging.(figure3-15) Figure3-15 B:To install the driver Selects "computer" in the computer, choice "management" with the right button, open the "device manager"-" network Adapter ", right-click uninstall "Microsoft Windows Mobile Remote Adapter".
Figure3-16 Figure3-17 19
Connect the Qmini M series industrial GIS data collector with pc again, if there is a "Windows Mobile member center" registered tip ,please choose "not registered". 3 software connection When the cable is connected ,the Microsoft ActiveSync in the computer will tips you "whether to need to establish cooperation relationship," choose “cancel”,Then Microsoft ActiveSync popup a hint, click "ok"。Then it has been connected successfully.
Chapter 4 Technology parameters The introduction of this section Technology parameters Technology parameters This chapter will introduces you related parameters of Qmini M series industrial GIS data collector, the product function will vary according to the different models. When you refer to this chapter, please refer to corresponding technical parameters according to the equipment you purchase.
Application function 5 million PXL camera with LED light √ supplement √ √ √ √ Integrated microphone and speakers √ √ √ √ √ Bluetooth √ √ √ √ √ Mini USB Port √ √ √ √ √ Micro SD Card, 32G Max. √ √ √ √ √ standard configuration 3.7V, 3100mAh lithium battery, working continuously √ over 12 hours √ √ √ √ 10 keys, with 4 direction keys and side √ shortcut key √ √ √ √ Size: 14cm×8cm×3.