A10 GNSS RTK Manual Manual Revision Revision Date Apr.2014 Revision Level 1 Description A10 GNSS RTK Manual1.
Content Preface ........................................................................................................ 4 1. Instruction ..................................................................................... 5 2. Your Suggestions ......................................................................... 5 Summary .................................................................................................... 6 1. Introduction ...............................................................
5. Intelligent Voice Module ........................................................... 29 6. Accuracy ...................................................................................... 29 7. Physical Feature.......................................................................... 30 8. Environment................................................................................
CHAPTER Preface 1 ■ Instruction ■ Your Suggestions 4
1. Instruction Welcome to A10 Series GNSS RTK system manual. This manual is designed for A10 GNSS RTK system, and use A10 GNSS RTK as an example to explain the installation, setup, and usage of the GNSS RTK system. If you have used other GNSS RTK system before, we suggests you read this manual carefully and this manual will help you to understand our A10 GNSS RTK system easily. 2.
CHAPTER 2 Summary ■ Introduction ■ Products Features ■ Usage and Notes 6
1. Introduction A10 GNSS RTK system adopts modularized design, so as to enable users to change into different differential transmission modules according to various requirements. Meanwhile the designed self-diagnosis function can automatically check the working status of all hardware and software of the A10 receiver while working, and arouse the problem part by its intelligent voice messenger in case of some problem.
2. 1+X multi-module communication units. 3. PCC Radio module (optional) compatible with Trimble/Leica RTK. 4. Double battery capacity as 5000mAh, 12 hours for RTK operating. 5. The highest performance in waterproof, dustproof and anti-drop. 6. Adjustable to be single GNSS system or multi-GNSS system: GPS, GLONASS, GALILEO. 3. Usage and Notes Although A10 receiver using chemical and impact resistance material, but necessary taking care and maintenance is still required for such a precise instrument.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Receiver Introduction ■ Introduction CHAPTER 3 ■ Receiver Appearance ■ Control Panel ■ Upper Cover ■ Lower Cover ■ Battery ■ Environmental Requirement ■ Electric Interference 10
1. Introduction This Chapter mainly introduces A10 receiver appearance, buttons and indicator led and so on. 2. Receiver Appearance Receiver Appearance mainly including 4 parts: upper cover, lower cover, guard collar and control panel, as Figure 3-1 Upper Cover Guard Collar Control Panel Figure 3-1 Receiver Appearance 3. Control Panel Lower Cover Figure 3-1, in the middle of red frame of A10 receiver is control panel.
Status led（red-green dual-color led） Power led(red-green dual-color led) Function Key: settings of working mode,satellite elevation angle,automatically base setting, reset receiver and so on. Function Key: settings of data link, collection interval, back to original setting. Power Key: setting confirmation, automatically base setting and so on. 4. Upper Cover Figure 3-2 indicates the upper cover of A10 receiver, the main function of which is anti-drop and anti-scratch.
5. Lower Cover As figure 3-3, lower cover of A10 includes communication module slot, battery groove, five-pin port, eight-pin port, loudspeaker and so on.
external power supply Eight-pin Port: connect A10 receiver with computer, or controller for data download and delete Protection Plug: anti-dust and waterproof for socket. SIM card slot: when choose GSM communication, install SIM card. SD Card Slot: install SD card to save large volume data. Joint Nut: fix instrument with tribrach and centering pole. Loudspeaker: voice broadcast for real-time operation and status. Tips: 1.
Anode Cathode Figure 3-5 Battery Back CAUTION! RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS 7. Environmental Requirement Even though A10 receiver uses waterproof materials, maintaining in a dry environment is still helpful.
Oil duct ( spark plug ) Television and computer monitor Generator Electric motor DC-AC power conversion equipment Fluorescent Light Power switcher 16
CHAPTER 4 General Operations ■ Introduction ■ Button Functions ■ Led Status Instructions ■ Static Data Storage ■ RTK Data Storage ■ Self-inspect and reset Receiver ■ Format Receiver ■ Power Supply System 17
1. Introduction Most of the operations of A10 receiver can be done by the three buttons on the mainframe panel. Buttons on the panel: Status Led Satellite Led Function Button F1 Power Led Power Button Function Button F2 Figure4-1 Mainframe Panel Explanations of buttons operations and leds hints as below: Operations Explanation Single click button Press a button less than 1 second Double click button Double click the button while the clicking interval should be between 0.
2.
the power led will flash to hints its power status Press F1 while than press power Auto-set base F1+Power buttonat the same time to turn on the button to turn receiver until hearing “Dingdong”. receiver Then the receiver speak out its current status. Single press F1 to selfinspection. Reset receiver and Long press F1 Single press F2 to reset the mother selfins pection board.
3. Led Status Instructions Led Power Instruction led In normal voltage: internal battery voltage >7.6V, Always on (yellow) external battery voltage >12.6V In normal voltage: 7.2V＜internal battery voltage Always on ≤7.6V, 11V＜external battery voltage ≤12.6V Slow flash Low power-pressure: inter≤7.
Error in static mode (typically for no more flash Fast flash memory) Communication module in error for getting data, Always on mainly resulted by problem in module so that no data output Satellite Always on More than 4 satellites tracked successfully Slow flash Loss satellites and try re-tracking led 1. mother board error resulting in no data output (green) while resetting receiver Off 2. mother board error resulting in no data output while in static mode 4.
5. RTK Data Storage The controller can be connected with the receiver via Bluetooth or cable, the data will be stored in the memory of the controller. After fieldwork finished, you can connect the controller with PC by the data cable, and then download the RTK data from the controller to PC by copying. 6. Self-inspect and reset Receiver Long press F1 button for more than 6 seconds, and then single press F1 to self-inspect or single press F2 to reset the mother board.
Warning: Make sure all useful data has been copied to another place for spare, because all data will be deleted forever after this format. 8. Power Supply System Install and Uninstall Battery Install: 1. Match with the in the battery slot to put in the battery. Figure 4-2 2. Insert battery towards “Close” end (see red arrow) to install it ok.
3. Close the battery cover. Figure 4-3 Uninstall: Slide the battery towards to the “Open” end, and then pull out battery. A10 Receiver Battery Name and Model Name Model 5000mAh lithium battery BL-5000 Lithium battery charger CL-8410 Power Supply Power Power supply way 1. lithium battery; 2.
If use external power supply for A10 by the eight-pin port and five-pin port on the mainframe, the power supply should be 6～36V with current no less than 500 mAh. When using both lithium battery and external battery, the receiver will check the power pressure of both batteries and choose the higher one. And please note that if use external power supply, must use the specified external power supply from to avoid any destroy to the receiver. Note: usually one A10 lithium battery can last 13 hours for static.
CHAPTER 5 Technical Parameters ■ Introduction ■ Receiver ■ Ports ■ Function Key and Indicator Led ■ Intelligent Voice Module ■ Accuracy ■ Physical Feature ■ Working Environment 27
1. Introduction Here we list out all Technical Parameters of A10 GNSS RTK SYSTEM. The Technical Parameters will be a little different according to your purchase order. Please make sure about your configuration then find out Technical Parameters correspondingly. 2.
3. Ports ◎ 2 RS-232 serial ports ◎ 1 USB port ◎ 1 port for wireless blue-tooth communication ◎ 2 port for external DC pow er supply (M ultiplex) ◎ 1 SIM card slot ◎ 1 SI M card slot ◎ 1 SD card slot ◎ 2 built-in Li-ion battery groove ◎ 1 built-in communication module port 4.
7. Physical Feature ◎ W ith A RM 9 Core Control Chip, built-in 1GB Flash Memory ◎ Di mension: φ182mm×h96mm ◎ Weight: 1.25 kg( Incl. li-ion battery) ◎ A nti-impact from 2 meters free-falling, waterproof in 2 meters deep water ◎ Li thium battery. W i th 2 standard battery in 5000 mAh , Voltage:7.
