Installation Instructions

1 2
3 4
1 2
3 4
tws earbuds pairing
• TWS Earbuds
• TWS Earbud Case
• USB-C Charging Cable
• Small,Medium and Large Earbud Tips
included
open case
rightleft
back
The buds will start to ash red and
white, this means that they are
ready to pair.
Use the Bluetooth settings on your
device to pair with HEYDAY EARBUD
05. Tap "pair" when prompted to
pair with HEYDAY EARBUD 05. You
may be prompted again if pairing
for the rst time tap "pair" when
prompted. When the earbuds have
successfully paired they will turn
white ve seconds and then fade.
To reset the earbuds to factory
settings, place them both into the
case and with the lid open and hold
the reset button on the back of the
case for 6 seconds
To pair the earbuds to your device
for the rst time open the case and
remove both earbuds.
1 2
3
1 2
3
earbud tips
To change the size of the earbud
tip, squeeze it and pull it away from
the earbud.
Select the size that is the most
comfortable for you and push it
onto the earbud. The earbud tip has
an interior sleeve that slides onto
the earbud. Repeat steps 2 and 3
for the second earbud.
The earbuds come with small,
medium and large earbud tips and
can be changed at any time.
earbud power
indicator
earbud power
indicator
touch sensor
microphone
touch sensor
microphone
input
USB-C
port
reset
button
indicators
Earbud Rapid Flashing Red/White - Pairing mode
Earbud Flashes White and Fades - Paired
Earbud Flashing Red - Low power
Earbud Solid Red - Charging
Earbud No Light - Charging complete
Case One Light - 25% charged
Case Two Lights - 50% charged
Case Three Lights - 75% charged
Case Four Lights - 100% charged
Ascending Tones - Power on
Descending Tones - Power o
Three Rapid Tones - Ready to pair
Single Chime - Paired
Two Rapid Dings - Low battery
Quick Ascending Tone - Max volume (iOS only)
Quick Descending Tone - Min. volume (iOS only)
case power
indicator
touch controls
left earbud
- play/pause
1 tap 1 tap
- answer/end
- call
2 taps
- prev song
- reject call
hold 1.5 sec.
hold 1.5 sec.
- voice assist
5.31 inch
cut line
fold line
20 inch
• If the earbuds are not working correctly place them into the case with the lid open
and reset them
• If the earbuds won’t turn on, recharge the battery and try again
• If the earbuds won’t charge, make sure the power supply works, is 5V>1A, not
damaged and that the case is charged
• If the earbuds make no sound or do not show as an available device, make sure they
are not paired, if so unpair the device and repair to the desired device
• Do not use near any water source
• Do not modify or repair this device
• Do not use chemical detergents to clean your device, use a soft dry cloth
Can’t get it to pair? Have a question or comment?
call us at: 877-698-4883 or: 877-MyTgtTech
online at: TargetTechSupport.com
FCC ID: 2AO23-TW15 Model: TW15 Input: 5V Max 1A Made in China
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause
harmful interference, and 2) this device must accept interference received, including interference that may cause undesired operation.
Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Target Corp. Mpls. MN, 55403 Phone: [phone]
Place both earbuds back into the case
Charging is complete when lights turns o
Full charge requires approximately 1 hour
charging earbuds
• Use the earbuds in mono mode by only removing one earbud from the case
mono mode
• Plug USB-C end of charger into the back of the case
• Plug USB end into a power supply of at least DC 5V 1A warning: please use UL
compliant power supply 
• Full charge requires approximately 2 hours and will provide 24 hours of earbud use
• Charging is complete when all 4 LEDs are solid white
charging case
• The earbuds are resistant to sweat which means they’re perfect for workouts note:
the charging case does not have the same rating and should be used in the same conditions
IPX5 water resistance
right earbud
- play/pause
1 tap 1 tap
- answer/end
- call
2 taps
- next song
- reject call
hold 1.5 sec.
hold 1.5 sec.
- voice assist