User's Manual

FCC ID: 2AO23-QIC42 Model: QIC42 Input: DC 9V/2.22A Output: MagSafe Charger 15W Made in Vietnam
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not
cause harmful interference, and 2) this device must accept any interference received, including interference that may cause
undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
Target Corp. Mpls. MN, 55403 Phone: [phone]
• If you’re having issues charging use the tips below to help:
• Double check that the USB-C cable and Power Delivery wall plug are plugged in
• Certain phone cases may interfere with MagSafe
®
charging; remove the phone case
for best results
• Double check the placement of the device on the magnetic charging pad; for best
results, the center of the device should be on the center of the magnetic charging pad
• MagSafe
®
charging is compatible with iPhone
®
12 and newer as well as other Qi-enabled
devices; please consult your devices user manual if you are unsure if your device
is compatible
• Remove credit cards and other cards with magnetic strips to prevent damage to the cards
• Keep the charger away from heat and direct sunlight
• Do not modify or repair this device
• Do not use in high temperatures or extreme weather
• Do not use chemical detergents to clean your device, use a soft dry cloth
• Immediately unplug it from its power source if it gets wet
• Remove the protective lm on the Power Delivery wall plug before using
safety
Does not
charge Apple
Watch
®
Can’t get it to charge? Just have a question?
call us at: 877-698-4883 or: 877-MyTgtTech
e-mail us at: TargetTechSupport.com
need some help?
When properly
aligned the
device will stick
to the pad and
the charging
screen will appear
If the device will
not stick to the
pad, remove
the case and
try again
troubleshooting
MagSafe P
ad
top
• The device should stick rmly to the pad when charging
• Thick phone cases as well as some materials can interfere with MagSafe
®
charging
• This is a high speed magnetic charging pad, make the most of the charger by using
the Power Delivery wall plug that was packaged with it; using a dierent power source
may charge your device at a slower speed
quick tips
• Magnetic charging pad with attached charging cable
• Power Delivery wall plug
included
• Place the magnetic charging pad on a sturdy at surface
• Connect the Power Delivery wall plug to the wall outlet using the attached USB-C
cable (recommended)
• If you need to use a dierent power source make sure it is a USB power supply of
DC 9V 2.22A minimum warning: please use UL compliant power supply
• Place your MagSafe
®
compatible device onto the magnetic charging pad; the
device will stick to the pad and the screen will indicate that it is charging
• Remove credit cards or any card with a magnetic strip to prevent damage
to the cards before charging
• Charge time will vary by device
charging