User's Manual

charging car mount
installation
The car mount comes in two
separate pieces and requires some
assembly.
dash arm car mount
1
2
To assemble insert the ball joint on
the dash arm into the back of the
car mount. Be sure not to press too
hard so you do not damage either
part of the mount.
3
Twist the nut on the on the dash
arm to attach it to the car mount.
Be sure to twist the nut all the way
onto the mount or it will not stay up
right when the phone is inserted.
nut
4
screw
lock
Clean the dash board or window and
place the assembled mount onto it.
Press down the lock under the arm
to lock the suction. Then adjust the
dash arm and tighten the screw to
lock it into the desired position.
6
FCC ID: 2AO23-CAB66 Model: CAB66 Input: 9V 2A 12V 1.5A Output: 10W Max Made in China
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause
harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired
operation.
Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
Target Corp. Mpls. MN, 55403 Phone: [phone]
• Remove credit cards and other cards with magnetic strips to prevent damage to the cards
• Keep the charger away from heat and direct sunlight
• Do not modify or repair this device
• Do not use in high temperatures or extreme weather
• Do not use chemical detergents to clean your device, use a soft dry cloth
• Immediately unplug it from its power source if it gets wet
safety
• Double check that the USB-C charging cable and car charger are plugged in
• Certain phone cases may interfere with wireless charging. Remove the phone case
for best results
• Double check the placement of the device on the wireless charger. For best results,
the center of the device should be on the center of the wireless charger
• Wireless charging is compatible with iPhone 8 and newer as well as other Qi-enabled
devices. Please consult your devices user manual if you are unsure if your device
is compatible
troubleshooting
Can’t get it to charge? Just have a question?
call us at: 877-698-4883 or: 877-MyTgtTech
e-mail us at: TargetTechSupport.com
need some help?
8 in
front
back
coverpage 4
page 2 page 3
how to fold
DO NOT PRINT
coverpage 4
5
To open the mount press the two
buttons on the bottom of the car
mount at the same time. The arms
will automatically span out.
button button
Place your phone into the mount
and press the arms in to secure it. If
you need to adjust or remove your
phone follow step 5.
7
Certain surfaces may cause issues
with the suction lock. If you’re
having issues use the mounting
plate to create a smooth surface.
To use it, clean the desired surface,
remove the adhesive backing, press
on the desired location, and wait
3-5 minutes before use. Follow step
4 to mount.
7
Driving while distracted is
dangerous. Do not use your phone
while your vehicle is in motion.
Check your states laws on window
and dash mounts to ensure you’re
not breaking them.
warning:
• If the mount won’t stay upright be
sure that the dash arm is fully
screwed into the mount
• If you can’t remove the dash arm,
make sure the lock is ipped up
and use the tabs on the suction
cup to help break the seal
• If the suction cup is having issues
sticking, it may need to be
cleaned. Rinse under cold water to
wash away any debris and refresh the
sticky gel. Wait for it to dry before use.
installation tips
bottomfront
usb-c
port
charging
indicator
• Follow the assembly instructions and make sure the mount is secure and in the
desired position
• Plug the car charger into the aux outlet and connect to the car mount using the
USB-C charging cable
• If you need to use a dierent power source make sure it is a USB power supply of
DC 9V 2A minimum warning: please use UL compliant power supply
• Place your QI-enabled device onto the wireless charger and align the device with
the center of the charging surface or the device will not charge
• Remove credit cards or any card with a magnetic strip to prevent damage
to the cards before charging
• Charge time will vary by device
charging
• Alignment matters - centering the device on the charging surface ensures the
fastest and most ecient charge
• Thick phone cases as well as some materials can interfere with the ability to charge
• This is a high speed wireless charger. Make the most of the charger by using the
USB-C charging cable and car charger that were packaged with it. Using a dierent
power source may charge your device at a slower speed.
quick tips
• Wireless charging car mount
• USB-C charging cable
• Car Charger
• Solid Red - Charging your device
Solid White - Fully charged
Flashing Red - Foreign object detection, pieces of metal or other materials may cause
overheating and damage your charger or phone. Remove them immediately.
indicators
included