User's Manual

ManualsBrandsHextronik ManualsElectronicsORX GEORGE 4 servo receiver with stabilizer and ESC

Page 1 of 9

RANGE

EORGE

ERVO

ECEIVER WITH

TABILIZER AND

ESC

SER MANUAL

FCC

ID:

2AOCYGEORGE

RODUCT OVERVIEW

ESCRIPTION AND FEATURES

The device combines 4 devices in one, compact format

1. 12 channel DSM2/DSMx compatible receiver

2. 3 axes stabilizer working with various planes configurations and having 3 different types of stabilizing behavior.

3. 6A continuous 10 peak brushless ESC

4. 1.5A 5V switching BEC for servos.

5. Working voltage is 7.4~12.6VDC (2s or 3s batteries)

ECEIVER

• Diversity antennas for perfect reception and telemetry of micro models (500m LOS)

• Integrated telemetry for real time readings:

- Battery voltage

- Receiver voltage

- Lost packets (signal quality)

Range: 500m LOS (Line Of Site) or more**

Telemetry range – up to 200m. LOS or more**

ESC:

ESC- 6A continuous, 10A peak integrated ESC for BLDC motor. It is already calibrated to work with stabilizer in airplane mode.

Summary of content (9 pages)

PAGE 1
ORANGERX GEORGE 4 SERVO RECEIVER WITH STABILIZER AND ESC USER MANUAL FCC ID: 2AOCYGEORGE PRODUCT OVERVIEW: DESCRIPTION AND FEATURES: The device combines 4 devices in one, compact format 1. 12 channel DSM2/DSMx compatible receiver 2. 3 axes stabilizer working with various planes configurations and having 3 different types of stabilizing behavior. 3. 6A continuous 10 peak brushless ESC 4. 1.5A 5V switching BEC for servos. 5. Working voltage is 7.4~12.
PAGE 2
DIMENSIONS: 39x28x8 mm WEIGHT 9.3 grams (including wires and connectors) CONNECTIONS: The receiver has following connections: - Battery connector – connect to your power battery using JST connector. - 4 1.5mm Molex connectors for servos S1 – Ailerons S2 – Elevator S3 – Rudder S4 – Gear (can be programmed as second Aileron or Flaps or any other output needed) - 1 1.5mm Molex connector for PC connection via UART to USB adapter - 3 leads to connect brushless motor (black thick wires).
PAGE 3
The receiver will work with any DSMx/DSM2 compatible transmitter or Tx module. There is two ways to initiate binding procedure: 1. Manual binding by power ON with pins 2 and 3 on UART connector shortened; 2. Autobind - after 30 seconds of no known signal from transmitter received the device will initiate binding procedure. If the receiver didn’t see any transmitter in binding mode nearby for 30 seconds, the receiver will turn binding mode off for safety reasons.
PAGE 4
SETTINGS VIA PROGRAM CARD (SOLD SEPARATELY): 1. Page 1 of PID settings. Click the roller wheel to enter the menu You can chose the axis to change – ROLL, PITCH, YAW . Step on the axis whose parameters you want to edit. Click Enter again. Now you can navigate between P, I and D parameters. Click enter again. The edited parameter will start blinking. Use roller to change the value. When value is changed press Enter again and exit the value changing mode.
PAGE 5
2 Page 2 of PID settings. Beginner sens – sensitivity for Beginner mode. If sensitivity is too high the model can start oscillating. Lower sensitivity in this case. Advance sens – sensitivity for Advanced mode. If sensitivity is too high the model can start oscillating. Lower sensitivity in this case. Stick param – the parameter how far from the center a control stick needs to be to disable autolevel in advanced mode. The value range is 0…255 from stick in middle to the extreme position.
PAGE 6
4 Page 4 Servo output settings Press Enter on dial to enter the menu. If you need to change the servo you want to set, press Enter again and the cursor will highlight servo name (Ail, Rudd,etc). Press Enter again to exit from the servo selection submenu. Servo – name of channel, (Ail1, Ail2, Elev, Rudd) which will be set; Min – Lowest servo endpoint (us). Range is 1000us…2000us Mid – middle position of the servo (us). Changing this parameter you can subtrim servo in middle point.
PAGE 7
6 Page 6.Model type and throttle settings. Mdl type – you can chose appropriate type of your model for servo mixing. Available options: "F-Wing", "Classic", "V-Tail" Min thr – Minimum throttle for ESC when the throttle stick is low Max thr – Maximum throttle for ESC when the throttle stick is high Min command – Minimum throttle for ESC during initial calibration on start. Please note: If the model type is changed, all previous settings will be erased and set to default values.
PAGE 8
. Page 8. Channels’ inputs . Program Card can act as Transmitter when it works with the stabilizer. In this mode Program Card outputs channel values to the receiver imitating transmitter. In this mode you can change these values as if you would do this using. You can set values on the each servo output. This is very useful for mechanical setup of planes for example. 9. Page 9. Device info. *Note: 1) This is not a Spektrum DSM2/X product, nor is it a copy of a Spektrum DSM2/X product.
PAGE 9
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.