CMM ACCESSORIES dCC (DIGITAL CONTROL CENTER) JOGBOX – CORDLESS AND TETHERED VERSIONS USER MANUAL H00017135 Rev01
© Copyright April 2020 Hexagon Manufacturing Intelligence All rights reserved. Hexagon Manufacturing Intelligence is part of Hexagon. Other brands and product names are trademarks of their respective owners. Hexagon Manufacturing Intelligence believes the information in this publication is accurate as of its publication date. Such information is subject to change without notice What is documented in this manual is a product of Hexagon Metrology, Inc.
Contents Contents ............................................................................................................................. iii Preface ................................................................................................................................ 5 Documentation Provided with the Jogbox ........................................................................................ 6 User Manual....................................................................................
Preface dCC is an operator control pendant often referred to as a jogbox for a Coordinate Measuring Machine (CMM). The pendant allows the operator to move the sensor portion of the CMM to a desired location in the work volume. In addition to driving the machine, dCC allows the operator to pull up part programs on the embedded tablet in the pendant. dCC is available either as a tethered wired version or a wireless version.
Documentation Provided with the Jogbox The information provided with the Jogbox offers a wide range of solutions for getting to know and using its functions. The Jogbox comes with a USB key containing the following documentation. User Manual Contains essential information on how to use the Jogbox safely and efficiently. The manual includes a detailed description of the Jogbox, the instructions for use, and the routine maintenance procedures recommended by Hexagon.
Safety Information All the operations described in this document for which you are responsible must be performed in respect of the national, local and company safety regulations. In case of conflict with said directives, please contact Hexagon. Purpose-conformant use The jogbox is available as a tethered or wireless version. In any event, the wireless version shall be able to be operated in a tethered configuration (Cable will supply power only).
2.5. Warnings Danger When removing covers or parts (except parts removable by hand), live parts can be uncovered and touched. Pay attention to all contacts. Danger In case specific maintenance or repair works must be carried out on the open machine with power switched on, this work should be undertaken by authorized personnel only. Danger Make sure to use exclusively fuses of the specified type and nominal current. Danger Basically, all international and national safety standards have to be observed.
2.6. Safety Devices Danger The system is equipped with specific safety devices for operator protection. These devices should never be put out of use, not even partially. Any infraction can lead to physical injuries! All safety devices have to be checked regularly for correct operation. Possible malfunctions have to be reported immediately to our local subsidiary. Refer to the corresponding operating instructions for further information on our safety devices.
Overview JogBox tethered and JogBox wireless with Base station The JogBox is a wireless interaction platform for all Hexagon CMM’s. It improves user experience, provides advanced functionality and allows for future enhancement, customization, and integration with the HMI Ecosystem. • The jogbox features a Windows 10 Tablet with virtual buttons in addition to physical buttons similar to standard Jogboxs. • Capability to run wireless or tethered. • Wireless version will have tethered back up capability.
ENABLE ENABLE Figure 2 - The Jogbox - Rear Radio Base Station : Connects to the controller and allows the jogbox to communicate with the controller.
Dimensions 2 mm 2 mm mm Compact housing design featuring a 5.7” touch panel. Jogbox Weight: Wireless 1.55 kg (3.42 lb) Tethered 1.40 kg (3.
BB 8 Software Architecture 错误!使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。 • 13
Operation EMERGENCY STOP SPEED CONTROL ENABLE JOYSTICK JOYSTICK MACHINE START EMERGENCY STOP This latching pushbutton causes an ESTOP condition when depressed. The Emergency Stop button is connected so that it interrupts the supply to the motor drive circuits by de-energizing a control relay. Joystick control is unavailable in this condition. To re-enable system, the ESTOP pushbutton must be unlatched; to do this rotate it clockwise 1/4 turn.
Keypad The JOGBOX keypad contains controls for operating the machine. The symbols in the following list of functions refer to the symbols on the Keypad diagram. The functions of these buttons are: PROBE ENABLE: This informs the operator of one of the following three conditions: • NOT ILLUMINATED - The probe is enabled, but the controller will not report hits. Note: Since all probe signals are ignored by the controller, the machine will not stop moving after the probe has registered a hit.
SHIFT: This is used to access the lower registers of buttons with two fields. (X/A, Y/B, Z/W, LOCK/UNLOCK, RUN/HOLD). When active, the lower registers can be accessed. W is for other machines with optional rotary tables. Power On/Off: AXES BUTTONS This constrains movement of the machine to the selected axes when the joystick is deflected. Axes with illuminated LED’s are active.
JOG MODE: PROBE/PART/MACH LEDs light to identify each motion mode that machine is in. These settings can be toggled to vary the way probe is manually steered. This promotes probe contact at right angles to part, which improves measuring accuracy and repeatability. • MACH: WHEN THIS LED IS LIT, PROBE MOVES IN THE O MACHINE’S COORDINATE SYSTEM. THIS IS THE DEFAULT POSITION. • PART: WHEN THIS LED IS LIT, PROBE MOVES ACCORDING O TO THE PART COORDINATE SYSTEM.
TOUCHSCREEN DISPLAY TOUCHSCREEN DISPLAY Log In Enter Passcode • Operator • Programmer 18 • dCC Jogbox – User Manual
Change Passkey Setting – Customize • Change Machine Picture • Language • Zero Joysticks • Set Logout time 错误!使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。 • 19
Audio - Notification sounds o Volume o Mute Power Management - Change Backlight Brightness - Set Auto Backlight Timeout 20 • dCC Jogbox – User Manual
Position – set the operator postition Check for updates - Swipe left to go to the Home page 错误!使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。 • 21
Home Page Swipe right to return to the Settings page - - • Type/Model of CMM • User Data • Interactive jogbox Manual • Machine Name • User Type Swipe right to go to the Routine page 22 • dCC Jogbox – User Manual
Swipe down to go to the JOGMode - Routine Page Swipe left to return to the Home page - Run Routine • • Load Edit programs o Load recent programs o Load favorite programs o Browse programs View Routine - Results 错误!使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。 • 23
- • Take picture - Camera Live View • Open Routine Swipe down to go to the JOGMode Run - Swipe down to go to the JOGMode JOGMode XYZ - Swipe right to go to the JOGModeWABC - Swipe right to return to JOGMode XYZ - Swipe up to return to the previous page 24 • dCC Jogbox – User Manual
Take picture / Favorite 错误!使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。 • 25
Alert (Popup) • Crash Detected • Controller Error • Software Error Resolve/Close/Dismiss Alert, returns to previous screen 26 • dCC Jogbox – User Manual
Appendix A – Battery Replacement Only personnel trained in proper handling and disposal should replace the Lithium batteries. Replace only with Lithium batteries of the same type from Hexagon and no others. Danger Do not handle the Lithium batteries without protection gear. Warning Batteries may explode is damaged.
Appendix B - Glossary Text… 28 • dCC Jogbox – User Manual
Declaration of Conformity Declaration of Conformity – Applies to European Union The 错误!使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。 • 29
FCC Statement FCC 15.19 (a) (3) This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC 15.21 NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.
IC statement This device complies with RSS-247 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
www.hexagonMI.
