User Manual

ManualsBrandsHewlett Packard ManualsElectronicsWireless LAN Access Device

1 of 542-10-0200-07

WAP-200 Quickstart

This quickstart guide shows you how to start up and test the WAP-200 intelligent wireless access point. For detailed configuration

and operating information, download the WAP-200 Administrator’s Guide from the Colubris Networks web site at www.colubris.com

(select Support and then Product Registration)

IMPORTANT NOTE ABOUT WIRELESS SECURITY: For easy access to the management interface through a wireless connection, the

WAP-200 ships with all wireless security options disabled. Colubris strongly recommends that once the unit is installed you enable a

wireless security option in order to properly safeguard the wireless network from intruders. For more information see the WAP-200

Administrator's Guide.

Hardware overview

Package contents

• WAP-200 unit

• Two 2.4 GHz (2 dBi) / 5 GHz (2 dBi) dual-mode omnidirectional

antennas

• Power adapter and power cord

• Mounting bracket

• Spring clip—if needed, insert into one of the screw holes in the

mounting bracket as shown to provide a tighter fit

Antennas

The WAP-200 has a single radio with two antennas. It can create a single

wireless cell. The antenna connectors are reverse-polarity SMA male

jacks. This means antennas or cable connectors must be SMA female

connectors with reverse polarity. Antennas can be either directly attached

or attached via a coax cable. Colubris recommends attaching to the MAIN

connector when using coax.

Reset button

• Press and release the button quickly to restart the WAP-200.

• To reset to factory default settings, press and hold the reset button

until the status lights begin to flash, then release.

Important: Resetting the WAP-200 deletes all your configuration settings, resets

the Administrator username and password to ‘admin’, and sets the IP address of

Port 1 via DHCP. If a DHCP server is not found connected to Port 1, the address

192.168.1.1 is assigned to Port 1 and the wireless port.

Installation

Important: Installation must be performed by a professional installer familiar

with local regulations governing wireless devices.

Important: Shielded Ethernet cables must be used for all connections.

Note: Do not connect the Ethernet port directly to a metropolitan area

network (MAN) or wide area network (WAN).

When mounting the WAP-200 on a wall, or ceiling ensure that

• The surface you attach the WAP-200 to and the fasteners you use are

able to support at least 5.1 kg (11.25 pounds)

• Cable pull (accidental or otherwise) does not make the unit exceed

the 5.1 kg (11.25 pound) limit

Note: Only indoor operation on channels 36 to 48—5.15 to 5.25 GHz—

is allowed.

Reset buttonPower

light

Wireless

light

Ethernet

light

Power connector

802.3af

5 volts

Reset

Port 1

10101

Serial port

Antenna connector

Front Rear

MAIN

AUX

Summary of content (5 pages)

PAGE 1
WAP-200 Quickstart This quickstart guide shows you how to start up and test the WAP-200 intelligent wireless access point. For detailed configuration and operating information, download the WAP-200 Administrator’s Guide from the Colubris Networks web site at www.colubris.com (select Support and then Product Registration). IMPORTANT NOTE ABOUT WIRELESS SECURITY: For easy access to the management interface through a wireless connection, the WAP-200 ships with all wireless security options disabled.
PAGE 2
Plenum installations Plenum rated cables and attachment hardware must be used if the WAP-200 is installed in a plenum. Since the optional WAP-200 power adapter is not rated for plenum installations, only the WAP-200 and appropriate cabling can be located in the plenum. Note: PoE injectors available separately from Colubris Networks cannot be installed inside the plenum. Configuration To configure the WAP-200 you use the built-in Web-based Management Tool.
PAGE 3
Regulatory information The WAP-200 complies with the following radio frequency and safety standards. substitution or attachment of connecting cables and equipment other than that specified by Colubris Networks Inc. Canada—Industry Canada (IC) The correction of interference caused by such unauthorized modification, substitution or attachment is the responsibility of the user. This device complies with RSS 210 of Industry Canada.
PAGE 4
Todos los productos con la narca CE cumplen con la directiva de compatibilidad electromagnética EMC (89/336/EEC) y la directiva de baja tensión (72/23/EEC) y implica conformidad con las normas de la Comissión de la Unión Europea. Products labeled with the CE 1313 with the optional alert sign “!” contain a radio transmitter that compies with the R&TTE Directive 1999/5/ED implying conformity to the following European Norms.
PAGE 5
Declaration of conformity Colubris Networks 200 West Street. Waltham Massachusetts, 02451, USA Declares that the WAP-200 conforms to the following standards; European Directives and European Standards • EMC Directive 89/336 EEC • Low Voltage Directive 73/23 EEC • Radio and Telecommunication Terminal Equipment Directive 1995/5/EEC • EN 60950-1 Safety • EN 300 328 V1.3.1 Data Transmission equipment operating in the 2.4 GHz ISM band • 5 GHz high performance RLAN 301 893 V1.2.3 • EN 301 489-1 V1.4.