Specifications

ManualsBrandsHET ManualsElectronicsBluetooth Module

Shenzhen H&T Intelligent Control Co., Ltd

HET-BA1611 Specifications

Summary

HET-BA1611 is a Bluetooth Low energy

module, using BA1611 as the main chip, the

chip is embedded with 32-bit MCU . AB1611

can be run independently Bluetooth 5.0

protocol stack and application profile.

HET-BA1611 has 64KB SRAM and

embedded 512KB FLASH, and has a rich

peripheral interfaces to meet different

application.

HET-BA1611 is an open platform, users

can implement their own applications based

on the Bluetooth protocol stack. We also

support a MESH firmware and one of the

most typical application firmware: UART

relay. Users can use this firmware to the

shortest development cycle to integrate

existing programs or products to the fastest

speed to market.

Applications

● Health Care

● Smart Home Application

● Motion Measurement

● Auto Electronics

● Leisure Toys

● Instruments

● Logistics tracking

Type

Function

Through

firmware

UART/BLE conversion with Clife

protocol.

UART/BLE conversion.

SDK

Product development based on

clife protocol.

Product development based on

AB1611 4 source Codes with

GAT ,GATT and GAP.

Summary of content (12 pages)

PAGE 1
Shenzhen H&T Intelligent Control Co., Ltd HET-BA1611 Specifications Summary HET-BA1611 is a Bluetooth Low energy module, using BA1611 as the main chip, the chip is embedded with 32-bit MCU . AB1611 Type UART/BLE conversion with Clife can be run independently Bluetooth 5.0 Through protocol stack HET-BA1611 and has application 64KB profile. SRAM Function firmware protocol. UART/BLE conversion. and Product development based on embedded 512KB FLASH, and has a rich clife protocol.
PAGE 2
Shenzhen H&T Intelligent Control Co., Ltd Content 1. Brief Introduction .......................................................................................................................................... 3 2. Product Features ............................................................................................................................................ 3 3. Interface Definition ..........................................................................................................
PAGE 3
Shenzhen H&T Intelligent Control Co., Ltd 1. Brief Introduction HET-BA1611 Bluetooth low energy module, using BA1611 as the core processor. This module follows Bluetooth 5.0 protocol, Runs in 2.4 GHz ISM band, GFSK modulation(Gaussian Frequency Shift Keying), 40 channel 2 MHz channel gap, three fixed radio channel, 37 automatic adaptive frequency hopping data channel, 2 MHz gap better prevent adjacent channel interference. The internal PA can deliver a maximum of 9.
PAGE 4
Shenzhen H&T Intelligent Control Co., Ltd ■Transmission Distance > 20m 3. Interface Definition 3.1Pin Assignments 3.2Pin Description PIN No.
PAGE 5
Shenzhen H&T Intelligent Control Co.
PAGE 6
Shenzhen H&T Intelligent Control Co., Ltd Item Min Type Max Unit Storage temperature -40 - 150 ℃ I/O supply voltage(VCCIO) -0.3 - 3.6 V Analog/RF supply voltage -0.3 - 32.0 V 20 dBm RF input Level 4.2 Recommended Operation Conditions. Item Min Type Max Unit Operating temperature range -20 25 85 ℃ Power supply 2.0 3.0 3.6 V I/O supply voltage (VCCIO 1.8 3.0 3.6 V 4.3 Typical current consumption Parameter Current(avg. 3V input) Units Tx current@9.
PAGE 7
Shenzhen H&T Intelligent Control Co., Ltd 6. Product Structure Size 7. HET UART pass through Firmware functions Operating Instructions 7.1 Transparent Mode and Command Mode Module can operate in transparent mode and command mode.
PAGE 8
Shenzhen H&T Intelligent Control Co., Ltd broadcasts started, open a specific APP phone will be scanned and docking, after a successful agreement can be monitored by BLE. Pass through mode: In this mode, users do not concern complex Bluetooth protocol application, you can complete the development of products in a short time BLE. MCU specific meaning users can be two‐way communication, user data through a common serial and mobile equipment module is defined by the upper application on their own.
PAGE 9
Shenzhen H&T Intelligent Control Co., Ltd 8. Furnace temperature of re-reflow 9. Module Package Information This module can be packaged with tape or tray after production, since this is ESD sensitive device, precautions should be used when handling the device in order to prevent permanent damage.
PAGE 10
Shenzhen H&T Intelligent Control Co.
PAGE 11
Shenzhen H&T Intelligent Control Co.
PAGE 12
Shenzhen H&T Intelligent Control Co., Ltd FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 1.