Installation Instructions

ManualsBrandsHES ManualsElectronicsComplete Electric Strike for Latchbolt Lock in Satin Stainless Finish

3062006.006, Rev. 1

1006 SERIES ELECTRIC STRIKE

1006 Electric Strike Body

Trim Enhancer (with screws)

Product Components

Electrical Specifications

ELECTRICAL RATINGS FOR SOLENOID

MINIMUM WIRE GAUGE REQUIREMENTS (One Way)

SOLENOID VOLTAGE

CONTINUOUS DUTY

12 VDC

.48

24 VDC

100

.24

Resistance in Ohms

Amps

Solenoids are rated at +/- 10% indicated value.

200 feet or less

200 - 300 feet

300 - 400 feet

18 gauge

16 gauge

14 gauge

18 gauge

16 gauge

12 & 24 Volt Pigtails

Keeper Shims (2, with screws)

Summary of content (8 pages)

PAGE 1
006 SERIES ELECTRIC STRIKE Installation Instructions ® 1 Product Components 1 2 1006 Electric Strike Body Trim Enhancer (with screws) 3 4 12 & 24 Volt Pigtails Keeper Shims (2, with screws) 1 4 2 3 Electrical Specifications ELECTRICAL RATINGS FOR SOLENOID CONTINUOUS DUTY Resistance in Ohms Amps MINIMUM WIRE GAUGE REQUIREMENTS (One Way) 12 VDC 24 VDC 25 100 .48 .24 Solenoids are rated at +/- 10% indicated value.
PAGE 2
Installation Directions CAUTION! Before connecting any device at the installation site, verify input voltage using a multimeter. Many power supplies and low voltage transformers operate at higher levels than listed. Any input voltage exceeding 10% of the solenoid rating may cause severe damage to the unit and will void the warranty. Preparing the Strike Preparing the Frame NOTE: For 12V DC, the pigtail marked “12 VDC” should be used. For 24V DC, the pigtail marked “24 VDC” should be used.
PAGE 3
Cutout Templates Inches [Millimeters] 1006 WITH CYLINDRICAL LOCKSETS 1006 WITH CYLINDRICAL LOCKSETS 1006 WITH MORTISE LOCKSETS Please note the horizontal centerline of the electric strike in relation to the centerline of the mortise lockset. CL Vertical Centerline Mortise Lockset Please note the horizontal centerline of the electric strike in relation to the centerline of the cylindrical lockset. Strike Prep CL Vertical Centerline Cylindrical Lock CL Strike 4" Strike Prep CL STRIKE [101.
PAGE 4
Complete Pac Options (continued) E Components Low Profile Floor Installation Deadbolt Catcher 1. Remove the 4-40 x 3/16” screws and standard floor from the electric strike as illustrated above. 6-32 x 1/4” Screws # 6 Lock Washers 6-32 Nuts 4-40 x 5/16” Screw 2. Install the Low Profile Floor using the 4-40 x 5/16” screw provided with the Faceplate Option Kit as illustrated above.
PAGE 5
Complete Pac Options (continued) H, HD, HM, and H2 Components Deadbolt Bracket Installation Deadlatch Bracket (HT and HTD only) 10-32 x 1/8” Screw 1. Install the Deadbolt Bracket using the 10-32 x 1/8” screw as illustrated above. If using an HT or HTD option, proceed to step 2. # 6 Lock Washers 6-32x 1/4” Screw (HT and HTD only) (HT and HTD only) 2. Install the Deadlatch Bracket using the 6-32 x 1/4” screw and #6 Lock Washer as illustrated above.
PAGE 6
Complete Pac Options (continued) R Components Low Profile Floor # 6 Lock Washers Hookbolt Bracket 4-40 x 5/16” Screw Hookbolt Catcher 10-32 x 1/8” Screw 6-32 x 1/4” Screws Installation 1. Remove the 4-40 x 3/16” screws and standard floor from the electric strike as illustrated above. 3. Attach the Hookbolt Catcher to the mounting plate using the 6-32 x 1/4” screws, #6 Lock Washers and the 6-32 nuts as illustrated above. 2.
PAGE 7
Faceplate Options CL = center line of faceplate HM, NM H, N HD, ND 5/32“ [3.97] K 1-11/32” [34.11] Z 1-3/32” [27.81] 1-3/4” [44.45] 27/32” [21.46] J, E 5/16” [7.79] 1-15/32” [37.29] 23/32” [18.22] 27/32” [21.46] 23/32” [18.22] 19/32” [15.46] 1-9/64” [28.83] R 29/32” [23.39] 1-11/32” [34.11] KM 2-7/8” [73.02] 7/8” [22.23] 23/32” [18.26] 1-1/16” [26.72] 1/8” [3.17] 3-1/8” [79.37] 3-1/8” [79.
PAGE 8
® HES, Inc. Phoenix, AZ 85044 800-626-7590 www.hesinnovations.com Copyright © 2017, Hanchett Entry Systems, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Hanchett Entry Systems, Inc. is prohibited.