User Manual

ManualsBrandsHENDUN ManualsElectronicsWireless Door Alarm with Remote, Windows Open Alarms,Home Security Sensor, Pool Alarm for Kids Safety, Prevent Robbery (2 Pack)

2019.10

KS-SF03R

2.1 Battery installation

3.2 Alarm Triggering

<10mm

Installation figure

Arrow-to-arrow alignment

3.6 Battery low power indication

3.4 Doorbell Function

3.5 Remote Controls Add-on Guides

Magnetic

Type

Extremely

Loud

Wireless

Remote

Wireless Door/Window

Security Alarm

User Manual

Remote

Low Power Indication LED

Magnet

2. Installation Guides

1. Operating Environment

3. User Guides

Doorbell

or Alarm

53x92 mm

正面

3.1.2 Press remote control [ ] key to the

Disarm at the Arm mode， the host will produces

a long

“

Bi……

”

sound and exit the Arm mode.

The host will in an idle condition except low power

indication function.

3.1.1. Press remote control [ ] key in silent mode

，The main device produces 3 times “Bi Bi Bi”

sound and enters into the Arm mode and LED

flashes at once every 3 seconds.

2.1.1. Remote battery installation: When remote

control range becomes shorter or LED light

becomes fade, please replace the battery. Use

minus (-) type of screwdriver to open the external

cover, replace 1 new 12V/27A battery. Caution:

Ensure correct battery (+) and (-) orientation.

2.1.2. Host battery installation: Slide on battery

cover and install 2 AAA size batteries.The host

produces a short “BI” sound after the batteries are

fully installed and also indicates the installation is

successful.

2.1.3. Use alkaline battery has a better performance

compare to other types of battery. Use other types of

battery may cause shorter battery lifespan or lower

alarm sound level.

● Remote door /window security alarm; Preset

alarm is triggered to produces loud alarm sound

when the door/ window opens.

● More easier to operate using remote control

with arm/disarm/panic /doorbell/coding keys

● More easier to assemble with double sided

tape at the host.

● The host has 108dB loud speaker, 2 pcs AAA

size batteries, Low power indicator.

3.3 Panic Function

2.2.1. Select door/window installation location

and clean up the installation surface with a clean

wiper. Remove the double sided tape liner at the

host and adhere the host to the clean surface of

door / window.

2.2.2. After installed the host, locate the magnet

nearby the host by align arrow-to-arrow marking

at same level position.

2.2 Host Installation

3.1 Arm and Disarm

3.2.1. The host at the Arm mode will be triggered

for 30 seconds in simultaneously if the door

opens. The host stops after 30 seconds and

triggers again after another 15 seconds for 30

seconds and it continues in the periodic mode

until either the door is properly closed or to disarm

the host using a remote control.

3.2.2. Direct press the Disarm key at remote

control to stop the host from alarming and exit the

Arm mode simultaneously

Doorbell/

Coding

1. 1. The host uses 2 AAA size alkaline battery.

1. 2. The remote control uses one 12V/27A

alkaline battery.

1. 3. The host can operates in silent mode

continuously more than 1 year

(Assume 5 times on-off/day)

1. 4. The remote control can operates in silent

mode continuously more than 1 year.

( Assume 5 times on-off/day )

1. 5. Operating environment temperatures:

-10~+60℃

1. 6. Operating environment humidity : R/H <80%

1. 7. Storage temperature: -20℃~+70℃

Cautions:

●

The host is applicable for indoor use only, do

not install that expose to sunlight, raining, high

polluted and high humidity area.

The host magnetic sensor is at right side,

assemble the magnet at right side of the host

and align arrow-to-arrow position.

If the host is installed at door side, install the

magnet at door frame side and vice versa to

ensure the magnet is away from the host when

the door opens to function properly.

Ensure distance between the host and magnet

is not more than 10mm when the door is fully

closed.

3.6.1. When the host’s LED flashes once/second,

it indicates battery power is low and replaces with

new batteries accordingly.

3.6.2. When the remote control’s flashlight

becomes dark/fade or remote control range

becomes shorter, it indicates the battery power is

low and replaces with a new battery accordingly.

3.4.1. When the host is not at the Arm mode,

press the key [ ] at remote control，the host

will produces a “ DingDong ” sound and enters into

doorbell function. Under this function, the host is

triggered at a doorbell mode sound to pre-alert

that the door/window is opens.

3.4.2 Press [ ] Disarm key or [ ] Arm mode

key once time, the host exits the doorbell mode

automatically.

At the same time, release the coding key at remote

control and press again at Arm or Disarm key once

time, the host produces 2 “Bi … Bi…” sound and

indicates the coding is successful.

3.5.2. Register the second remote control or more :

First, confirm the host is not in Arm mode (no

require to remove the host battery)，then press at

registered remote control’s coding key continuously

around 10 seconds (ignore the doorbell sound in

between) until the host produces once “ Bi…”

sound. This indicates the host was entered into

coding learning mode. At the same time, release

the coding key and press Arm or Disarm key once at

the remote control, the host produces twice

“Bi…Bi…” sound. This indicates the coding learning

is successful and ready to add another new remote

control.

When requires more remote controls to add-on,

the steps are as follow:

3.5.1. Register the first remote control: At first,

remove the host batteries and install back after 2

minutes; After listened once “Bi” sound, press at the

coding key around 10 seconds continuously, the

host produces “Bi…” sound. This indicates the host

was entered into the coding learning mode already.

Please follow remote control add-on guides above

for further details if want to add more remote

controls.

3.5.4. Be cautious of the host can caters up to 8

remote controls coding only, the first registered

remote control coding will be removed if exceeds 8

remote controls registration.

3.5.3. Decoding method: Be cautious to use this

function! The decoding is mainly for lost remote

control to be removed from the host. If there is not a

backup remote control, require to purchase a new

remote control for the lost remote control decoding.

After enter into the code learning mode, same as

3.5.1 step method, press [ ] key at remote control

， the host produces once “Bi ” sound to decode/re-

move the remote control-host pairing. No require

power reset of the host and press the remote control

[ ] key again to encode it inside the host.

Disarm

Arm

Panic

Host

3.3.1. When a robbery was entered into the

house or other emergency situation, press the

panic key at remote control to trigger the host for

30 seconds. The key can be used at any setting

mode.