User's Manual

ManualsBrandsHENAN ESHOW ELECTRONIC COMMERCE ManualsElectronics2 way Radio

-way Radio /

way Radio / way Radio /

way Radio /

Walkie

WalkieWalkie

Walkie-

-Talkie

TalkieTalkie

Talkie

Model: T-628

User Manual and Instruction

Getting Started

Installing the AA Batteries

Your radio uses 3 AA Alkaline batteries.

1. With the back of the radio facing you, lift the battery latch

up to release the battery cover and remove.

2. Insert 3 AA Alkaline batteries as shown on the inside of

the battery compartment.

3. Reposition the battery cover and press down to secure.

The Walkie-Talkie can use a NiMH rechargeable battery instead of 3 AA

Alkaline batteries.

Battery Meter

The battery icon shows the battery charge level, from full to

empty .When the battery is empty, the radio chirps periodically

after releasing . The radio powers off when the voltage drops

below a predetermined level to protect the rechargeable battery.

Note: Remove the batteries before storing your radio for extended periods

of time. Batteries corrode over time and may cause permanent damage to

your radio.

Turning Your Radio On and Off

After you insert batteries turn the radio on, the radio chirps and the display

briefly shows all feature icons available on your radio. The display then

scrolls through the available channels and Interference Eliminator Codes.

Press and hold button turn the radio off.

Page 1

Summary of content (8 pages)

PAGE 1
Getting Started 2-way Radio / WalkieWalkie-Talkie Installing the AA Batteries Your radio uses 3 AA Alkaline batteries. 1. With the back of the radio facing you, lift the battery latch up to release the battery cover and remove. Model: T-628 2. Insert 3 AA Alkaline batteries as shown on the inside of the battery compartment. User Manual and Instruction 3. Reposition the battery cover and press down to secure. The Walkie-Talkie can use a NiMH rechargeable battery instead of 3 AA Alkaline batteries.
PAGE 2
Setting the Volume - Press the up button to increase the speaker volume. Press the down button to decrease the speaker volume. The speaker volume level is indicated by the numbers 1-16 displayed. Control Buttons Use • Scan / to: • Turn radio on/off Get Use UP/DOWN to: Setting a Channel • Adjust volume 1. With the radio on, press , The current channel flashes. • Scroll through menus 2. Press up or down to set the channel. ♪/MON to: 3. Press PTT to save the channel setting.
PAGE 3
When you finish speaking, release PTT (press to talk, release to listen). Locking the Keypad Checking the Channel Before Transmitting To avoid accidentally changing your radio settings, press and hold Your radio has multiple channels shared on a “take turn” basis. For uninterrupted communication, do not talk on a channel if someone else is 3 seconds or until displays. You can turn the radio on and off, adjust the volume, receive, transmit, send a call tone, and monitor channels.
PAGE 4
Note: You cannot remove the channel your radio was set to when you started the scan (called your home channel). Setting the Sensitivity Level Alerts Adjusting your radio’s sensitivity level helps minimize the possibility of Setting and Transmitting Call Tones unintended noises triggering a transmission and helps the radio pick up soft Your radio can transmit different call tones to other radios in your group so voices. you can alert them that you want to talk. 1. Press To set a call tone: 1.
PAGE 5
to radio frequency electromagnetic energy: Setting the TX POWER LO/HI 1. Press until Two-Way Radio Operation pr displays. When using your radio as a traditional two-way radio, hold the radio in 1. Press UP or DOWN to select the LO OR HI level. 2. Press PTT to save the TX POWER LO/HI setting. a vertical position with the microphone one to two inches (2.5 to 5 cm) away from the lips.
PAGE 6
An improper condition can result in a risk of electric shock. Blasting Caps and Areas 4. To reduce the risk of damage to the cord or plug, pull the plug rather than To avoid possible interference with blasting operations, turn off your radio the cord when disconnecting the charger from the AC receptacle. when you are near electrical blasting caps, in a blasting area, or in areas 5. To reduce the risk of electric shock, unplug the charger from the outlet posted: “Turn off two-way radio.
PAGE 7
Corp.”. (Note: Even if you have a unit, we will not be able to honor the warranty unless you have a receipt which clearly state that you have brought the product from an XXX.) **The receipt cannot be torn or unreadable. If, within 180 days from the date shown on the receipt or the bill of sale, the unit fails due to a defect in workmanship or material as determined upon examination at the factory, Sondpex will, at its option and at no charge, to repair or replace the defective components of the unit.
PAGE 8
Page 13