User's Guide

ManualsBrandsHeath ManualsElectronicsWireless Remote Doorbell Transmitter

Brass Transmitter

Wireless Push Button

Accessory

The Heath

/Zenith Wireless Push Button Acces-

sory works with existing Heath

/Zenith jumper or

dip switch systems.

• Battery powered push button - No wires to run.

• 128 selectable codes allow more than one

chime system in the same house.

SL-6293/94/95 Brass Transmitter Series

(Style may vary from illustration)

Summary of content (8 pages)

PAGE 1
Brass Transmitter Wireless Push Button Accessory SL-6293/94/95 Brass Transmitter Series (Style may vary from illustration) The Heath®/Zenith Wireless Push Button Accessory works with existing Heath®/Zenith jumper or dip switch systems. • Battery powered push button - No wires to run. • 128 selectable codes allow more than one chime system in the same house.
PAGE 2
1. Install two lithium type CR1220 3 volt push button batteries (included). Remove back of case by pushing in tab on bottom with a small screwdriver. Make sure batteries are oriented properly (see page 6). 2. Set the push button dip switches to match the chime receiver code. See "Code and Tune Setting" section. 3. Test range. Temporarily position push button where you want it mounted. Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting. 4.
PAGE 3
Code and Tune Settings Code Settings Note: Most installations will not require you to change any jumpers or dip switch settings on your chime and push button. WARNING: Disconnect chime unit from power source before opening code access door. Close door and replace screw before reconnecting to power. The push button and chime communicate by using a code that can be changed by switching dip switch positions (or removing and/or adding jumpers) on both the push button and chime.
PAGE 4
is functioning properly. Note: Positions 1 through 7 must be exactly the same for both the push button and chime for this system to function. Tune Settings ® Your Heath /Zenith wireless chime has different selectable tunes: Ding (one note), Ding-Dong (two note), or Westminster (eight note) (Available on selected Heath®/Zenith chimes). The factory setting is for the Ding-Dong tune (or Westminster, when available). This tune can be changed by following the instructions below.
PAGE 5
Note: All models have both front and back door tune capabilities. You may purchase any Heath®/Zenith wireless push button for a second entrance. We recommend the back door use the Ding tune and the front door use the Ding-Dong tune (or Westminster tune, available on selected Heath®/Zenith chimes). Models that include two push buttons will come factory set for front and back doors. Decals on the rear of the push button will indicate its setting.
PAGE 6
Remove screw to open access door Note: Some models might require the use of tweezers to remove and replace the jumpers or a small screw driver to set dip switches. Inside Push Button Back of Chime (+) Positive Battery Terminal ON 1 2 3 4 5 6 7 8 12345678 Tune Setting (Not used on all models) * Code Settings 1-7 Must Match Both Push Button and Chime Tune Setting Replacing Push Button Batteries Install two lithium type CR1220 3 volt batteries.
PAGE 7
Troubleshooting Chime doesn't sound: • Make sure push button and chime codes are the same (See pages 3 through 6). • Check orientation of push button batteries (See page 6). • Check charge of push button and chime batteries (if applicable), replace if necessary. Batteries seem OK, but the chime doesn't work when installed: • Don't mount chime or push button on metal or near metal studs. This reduces the transmitter range.
PAGE 8
YOUR HEATH®/ZENITH FIVE YEAR LIMITED WARRANTY This is a "Limited Warranty" which gives you specific legal rights. You may also have other rights which vary from state to state or province to province. For a period of five year from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you. Batteries are not covered. To obtain a refund or a replacement, return the product to the place of purchase.