User's Guide

手机稳拍杆
使用说明书
产品规格
温馨提示
1.夹持手机时，尽量夹持手机中间位置，调节夹持
位置使其处于自然平衡状态，以降低电机工作负荷。
2.蓝牙连接10分钟之后无操作，遥控器将自动进入
休眠状态，重新按拍照键即可恢复连接。
3.使用遥控器时，当电量不足时，会有红灯闪烁
提醒，请应及时充电。
4.使用云台功能时，当电量不足时，会有红灯闪烁
提醒请应及时充电。
5.如果本机经历过剧烈温度或湿度变化，云台开机后
始终处于不平衡状态时，请将云台关机并拆下，然后
平放在水平桌面上开机后连续短按5次开机键，出现
3声短鸣1声长鸣后，会自动关机，然后再次开机，
云台复位成功，恢复正常平稳状态。
型号：H5
材质：ABS+铝
载重：300g
净重：230g
充电电压：5V
锂电容量：450mAh
工作时长：2H
遥控距离：10米内
遥控电池：CR1632
产品尺寸：190×70x40mm
伸缩长度：580mm
1 MicroUSB充电口
2 云台指示灯
3 云台开关键
4 锁定弹珠
5 旋钮锁
6 拉杆
7 遥控器指示灯
8 遥控器开关
9 三脚支架
产品描述
1.云台锂电充电
接MicroUSB接口进行充电，充电过程中指示灯红灯
长亮；充电完成后，红灯自动熄灭。
2 遥控器更换纽扣电池
关机
遥控器：长按拍照键3秒，蓝灯快闪三下熄灭，表示已关机。
云台：长按开关键5秒，绿灯熄灭，表示已关机。
充电方式 使用步骤
MicroUSB充电口
④
更换纽扣电池
CR163
①
拉出拉杆
②
向上推出
遥控器
⑦
放下拉杆
③
从侧边
打开遥控器
⑤
原路装回
⑥
向下推进
遥控器
1.长按遥控器开关键3秒开机，绿灯亮后熄灭，单击2下绿
灯闪亮
2.开启手机蓝牙，搜索配对”H5”设备，打开手机相机，
单击遥控器快门键即可拍照拍视频。
*极少数手机蓝牙遥控器实在无法操控拍照拍视频，请下载
360Camera App配合使用即可。
3.开启云台稳定功能
注意：尽量夹持手机中间
位置，保持手机处在自然
平衡状态，夹偏会导致电
机工作负荷过大，出现电
机发烫和电量过快用完的
现象。
3.2展开自拍杆
开启蓝牙
H5
指示灯
开关键
快门键
3.1打开手机夹子固定好手机
3.3云台功能开启
夹好手机调节位置保持手机处于
自然平衡状态，顺时针拨动手机
移开限位后，长按开关键5秒开机
开机后进入智能水平稳定模式，
转动支架手机始终保持水平或
竖直状态
单击云台电源键顺时针旋转90°
或直接拔动手机到横屏或竖屏
状态即可达到横竖屏切换
当云台没电或关机时，转动云台直至其和定位珠锁紧，可变
成普通的自拍杆作横拍使用。
云台旋转锁定
打开底部三脚架，把三脚架置于平面上，调节整体重心。
4.自拍杆模式
5.使用三脚架
产品型号： 系列号：
购买日期： 客户姓名：
客户邮箱： 联系电话：
联系地址：
以下情况不在保修范围内：
1.不能提供正规购买凭证和填写详细信息的保修卡
2.人为或不可抗因素造成的损害
*本公司保留对上述售后条款和限制进行最终解释的权利
质检员：
OQC inspector:
售后保修卡
合格证
Qualification Certificate
该产品经过严格检验为合格品
This product is strictly instpected as a qualified product
Dear customer,
Thanks for purchase of our professional products!
We warrants that your purchase is free from defects in materials
and workmanship under normal use during the limited waranty
period.The warranty begins on the original date of purchase on
your sales receipt.If service is required,a copy of the sales receipt
must be included with an explanation of the problem.
Model No: Serial No:
Purchase Date:
Contact Name:
Contact Email:
Product Defects:
The followings cases are not included under the warranty:
1.Unable to provide legitimate receipt and warranty card
with correct informaiton.
2.The damage caused by human or irresistible factor.
The Product is strictly inspected as a qualified product.
Inspector:
Warranty Card
Qualification Certificate
Handheld gimbal
User Guide
Product Specification
Model No:H5
Material:ABS+AL
Playload:300g
N
et Weight:230g
Battery Capacity:Li-ion 450mAh
Charging Port:Micro
USB
Charging Voltage:5V
Working Current:100mA~2100mA
Operation Time:2H
Charging Time:1H
RCU Control Distan
ce:Within 10m
RCU Battery:Lithum Cell CR1632
RCU Modulation Type:GFSK
Product Size:190*70*40mm
Extension Length:580 mm
1 Micro USB Port
2 Gimbal LED Indicator
3 Power Key
4 Positioning Bead
5 Rotation Lock
6 Pull Rod
7 Controller Indicator
8 Controller Switch
9 Tripod
Overview
Charge the gimbal with the Micro USB cable and USB adaptor,
When charging,the red LED turns on and the indicator will be
off after the charging is finished
Power Off Machine
Controller Powe Off:Press the switch key for 3 seconds
and the blue light flashes out,indicates shutdown.
Gimbal Power Off:Press power key for 5 seconds,
the green LED goes out,indicates shutdown。
Charging for Gimbal
Micro USB Port
Change Battery for Controller
①
Move up
the rod
②
Push out
Controller
③
Open the topcover
out of Controller
⑤
Cover the top
⑥
Slot in
Controller
④
Change battery
CR1632
⑦
Move down
the rod
1.Press the controller switch for 3 seconds to power on the RcU,the
green LED turns on,
2.Turn on Bluetooth on mobile phone,search and connect to bluetooth
device named"H5",open camera App on phone after bluetooth
connection is succeed,click shutter key to take photos and videos.
3.Open the phone clip and place smart phone in holder,move and
adjust the holding position until phone is fixed in balance level.
*If the gimbal is not well-balanced and turn it on in this state,it would be over heat
or cause excessive power consumption.
User Guide
Shutter Key
H5
Indicator Light
Best Balance
4.Turn On Gimbal Function
Rotate the gimbal unit clockwise to make it
out of control by positioning bead,press
the power key for 5 seconds to turn on
gimbal function.
Take photos or videos under gimbal mode
Click power button of gimbal,gimbal will rotate 90 degree
clockwise then switch automatically between vertical screen
mode and landscape mode.
When the gimbal function shuts down
or battery uses off,turn around the body
until it is locked with the positioning bead,
it can be used as a traditional setfie stick.
90°
Reminder
1.If the gimbal is not well-balanced before turn on,it would
be over heat or cause excessive power consumption.
2.Bluetooth RCU goes into sleep mode automatically if there is
no any operation within 10 minutes,and click the power key to
wake it up.
3.When the battery of gimbal is low,the red LED is flash,please
charge the gimbal.
4.when the battery of RCU is low,the red LED turns on,please
change the cell battery of CR1632.
5.If the machine has been undergone drastic temperature or
humidity changes and the gimbal is not being in balance level
after power on,the gimbal should be calibrated again as below:
Turn off gimbal and remove the gimbal unit out of stick,then
put it on a flat table,power it on,click the power key 5 times
in succession,the gimbal shall make 3 short beeps plus 1 long
beep,then boot up again,gimbal function recover to the nomal
status successfully.
FCC Statement
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for
help
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions
(1)this device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Tripod Function
Open the tripod,place it on a horizontal
table and adjust the overal center of gravity
and avoid tilting.