User Manual

ManualsBrandsHAWKEYE ManualsCar & Vehicle ElectronicsHawkEye D10DX.01T In-Dash Depth Sounder with Air and Water Temperature (Includes Airmar Transom Mount Transducer)

www.hawkeyeelectronics.com

To ensure safety and many years of trouble-free

operation of your product, please read this

manual carefully before using this product.

SAFETY INFORMATION:

• Periodically wipe the face with a dry cloth. Do not use abrasives or

solvents on this device.

• Only qualified personnel should perform repairs or servicing not covered

in this manual.

• The LCD used in the product is made of glass. Therefore, it can break

when the product is dropped or impacted.

• Keep this product away from heat sources such as radiators, heaters,

stoves and other heat generating sources. Do not store in extreme

temperatures above 150° F (65° C).

• Shade the LCD during storage. Do not expose LCD to direct sunlight for

extended periods of time. Use the supplied cover at all times during

storage.

NOTES, NOTICES, AND CAUTIONS

WARNING: Indicates a potential for property damage, personal injury or

death.

IMPORTANT: Indicates potential damage to the device and tells you how to

avoid it.

NOTICE: Indicates important information that helps you make better use of

the device and tells you how to correct a performance problem.

INFORMATION: Indicates resources to obtain the proper information to help

you make the most of your device.

INFORMATION:

Read this manual completely before attempting to use or

install your device. Visit our Customer Service Center on our

website for advanced troubleshooting and technical support.

WARNING:

This depth sounder should not be used as a navigational aid

to prevent grounding, boat damage, or personal injury. Always

operate the boat at slow speeds in unfamiliar water, or if you

suspect shallow water or submerged objects.

Model No. D10D

INSTALLATION AND OPERATION MANUAL

D10DX.01T – Digital Depth Sounder with Air & Water Temperature, Transom Mount Transducer

Summary of content (19 pages)

PAGE 1
Model No. D10D INSTALLATION AND OPERATION MANUAL D10DX.01T – Digital Depth Sounder with Air & Water Temperature, Transom Mount Transducer To ensure safety and many years of trouble-free operation of your product, please read this manual carefully before using this product. SAFETY INFORMATION: • • • • • Periodically wipe the face with a dry cloth. Do not use abrasives or solvents on this device. Only qualified personnel should perform repairs or servicing not covered in this manual.
PAGE 2
PARTS SUPPLIED IN PACKAGING The following parts should be included with the display: • • • • • • • Digital Depth Sounder Display White and Black Faces and Bezels (optional on some models, see package for details) Display Sun Cover (optional on some models, see package for details) Thick Dash Extension Rod (optional on some models, see package for details) Flush Mount Bracket and Hardware Display Power Harness and Waterproof Fuse Holder Attached to the Unit Air Temperature Sensor and Harness Connected to th
PAGE 3
If you think that the transom mount transducer is not suitable for your installation, return to the place of purchase and exchange for the thru-hull (D10DX.06T). You can also visit our Customer Service Center at www.hawkeyelectronics.com to contact us or to complete a transducer exchange request to exchange the transducer for one that is specialized for your vessel. You may also call 888766-7276 to inquire about exchanging the transducer.
PAGE 4
NOTICE: The display can also be surface mounted using the Adjustable Surface Mount Bracket (1000-10). Please visit our website or contact us by phone for purchase information. You must attach the extension rod to the mounting stud on the back of the display housing before inserting the display into the Surface Mount Bracket. STEP 2 Installing the Face and Bezel 1. Place the face (B) over the display making sure to line up the cut outs on the face with the notches on the display. 2.
PAGE 5
STEP 3 Connecting of the Power Cable The display has no ON/OFF switch. Therefore, you will need to connect the power harness to a power source that will turn the unit on as power is applied. The key switch or an ON/OFF power switch will be suitable for powering the unit. 1. Connect the BLACK wire in the harness to a negative (-) terminal or suitable ground. 2. Connect the RED wire in the harness to a positive (+) 12 Volt switchable power source (key switch, on/off switch, terminal block, etc).
PAGE 6
3. Remove the fuse and check for 12 volt power at the spring located inside the fuse housing that is connected to the vessel’s power source. If 12 volt power is present continue to the next step. If power is not present, return to Step 1. 4. Insert the fuse and check for 12 volt power at the end of the fuse. If 12 volt power is present continue to Step C. If power is not present, replace the fuse. 5. Reassemble the fuse housing.
PAGE 7
To Change the Mode: 1. Press the “UP” Button to change the mode to the Right (The display will change modes from Depth to Water Temperature to Air Temperature) 2. Press the “DOWN” Button to change the mode to the Left (The display will change modes from Depth to Air Temperature to Water Temperature) NOTICE: When a Temperature Mode is selected the Water or Air indicator will flash on the LCD for 5 seconds while the temperature is calculated.
PAGE 8
DEEP WATER ALARM The deep alarm function can be set for depths ranging from 3 to 200 feet and triggers an alarm when the depth is more than the setting. You must be in the “Depth Sounder” mode to adjust this setting. To set the DEEP ALARM (lower alarm): 1. Press and hold the "UP" and “DOWN” keys until the and indicators illuminate and the icon blinks. (approximately 3 seconds). 2. Release the Keys. 3. Press the "DOWN" key to access the deep water alarm setting.
PAGE 9
The maximum Keel Offset setting is 20 FT (6.1 M), and can be set in .1 (1/10th) Feet or Meter increments. The unit will read “---” when a negative value occurs due to the Keel Offset subtraction. To set the Keel Offset: 1. Press and hold the "UP" and “DOWN” keys until the K/O indicator begins to blink. (approximately 6 seconds). 2. Release the Keys. 3. Press the "UP” key to increase the Keel Offset value. Press the "DOWN" key to reduce the value. 4.
PAGE 10
MOUNTING THE TRANSDUCER Tools & Supplies Required for Installation • • • • • • • • • • • Power Drill 3/4”” (19 mm) drill bit, hole saw or spade bit 1/8” (3 mm) drill bit 9/64” (4 mm) drill bit Marine Sealant/Caulk 30 Grit Sandpaper “Phillips” Screwdriver Pencil Tie Wraps Water Based Antifouling Paint Masking Tape Transom mounting is suitable for the following vessels: • Outboard, inboard/outboard, single inboard, or jet-drive propulsion. • Hull deadrise angle below 30°. • Transom angle from 3-20°.
PAGE 11
STEP 1 Choosing a Mounting Location To obtain the best performance, the transducer should be mounted in a location where the water flow beneath the hull is aeration and turbulence-free. Try to mount the transducer as close to the centerline of the boat as possible. Consult the boat manufacturer for the best in-hull transducer placement. If this information is unavailable, follow the guidelines below. A.
PAGE 12
Mounting Location “DONT’s” NOTICE: To deliver consistent, accurate readings, the transducer must have a continuous supply of nonturbulent water. Do not mount the transducer in an area of turbulence or bubbles. Never install the transducer where the boat may be supported during trailering, launching, hauling, or storage. NEVER MOUNT: A. Behind water intakes, discharge openings, or thru-hull fittings. B. Behind strakes, struts, or hull irregularities. C. Behind transom steps or pockets. D.
PAGE 13
STEP 2 Assembling the Transom Mount Bracket A 1. With the Locking Tab in the up position, align the transducer and bracket, then slide the transducer into the Pivot Bracket until it cannot slide any further (minimal force is required) (illustration A). 2. Press the Locking Tab down against the Pivot Bracket until it locks firmly into place. 3. Slide the Pivot Bracket arms through the back of Screw Bracket as pictured. (illustration B). 4.
PAGE 14
4. The bracket is designed for a standard 13° transom angle. To determine if the plastic shim is needed, position the transducer at the desired location. Using a straight edge, compare the underside of the transducer relative to the underside of the hull. The stern (trailing edge) of the transducer should be 1/16" - 1/8" (1 - 3 mm) below the bow (leading edge) of the sensor. 5. Apply a marine sealant to the threads of the two #10 x 1-1/4" self-tapping screws and screw the bracket to the hull.
PAGE 15
STEP 4 Cable Routing Route the transducer cable over the transom, through a deck or splash-well drain hole or through a new hole drilled in the transom. If a new hole is required, it MUST be drilled well above the waterline. To Drill a Cable Pass Through: 1. Mark the desired location with a pencil. 2. Check for obstructions behind the desired location inside the hull. 3. Drill a 3/4” or 19 mm hole through the transom. 4. Route the cable through the transom. 5.
PAGE 16
NOTICE If you need to increase the length of the transducer cable order part # 8000-90 from our website or toll free at 888-766-7276. Strip back the rubber cable cover 1” (28 mm) exposing the three internal wires (blue, white, and bare) on your transducer. Using a soldering iron, solder the blue, white and bare wires from the 8000-90 extension cable to the corresponding wires on your transducer.
PAGE 17
of the boat over the base of the transducer. The water should be "Clean" with very little turbulence (air bubbles). If there are any air bubbles or turbulence seen passing underneath the transducer, move the transducer farther down on the transom bracket. If the performance does not improve, move the transducer to "Clean Water" making sure to fill any unused screw holes with marine sealant.
PAGE 18
WARRANTY This device is covered by a 2 Year Limited Warranty. To be eligible for warranty coverage, you must register your product within 15 days of purchase. Visit our website for warranty details and to register. • To Activate Your Warranty: • Read and print out a copy of the warranty details for your records. • Complete the registration form our website. • Make a copy of your original purchase receipt and staple it to this manual.
PAGE 19
IMPORTANT: If printing this manual from a computer, make sure that your printer does not adjust the size of this template by aligning the template with the kickup bracket. If the sizes are different, check your printer settings to make sure the print size is 100% with no scaling.