WirelessCable PT -WC-G1 User Manual Model:PT-WC-G1 Version:1.
CONTENTS About the User Manual - Please read this manual carefully before you use this product and retain it properly for future reference. Contents About the User Manual 02 Brief introduction 02 Packing list 03 Interface Information 04 Quick Start Guide 07 Indicator Description 09 Specification 10 Trouble shooting 10 PT-WC-G1 Setup Instructions 11 - If there is any question or difficulty about the operation of product, please feel free to contact us or the dealer.
Packing List Structure & Interface Model：PT-WC-G1 Check the packing list details after unpacking. If any parts are missing, contact the dealer. For the parts involved in each model, refer to the packing list below. Wireless high-speed data transmitter PT-WC-G1 * 1 piece Base * 1 piece Model: PT-WC-G1 Antenna * 4 piece RESET button WPS button Network cable * 1 piece Power adapter (12V/2A) * 1 piece *All accessories are subject to the actual products.
1. DC IN: This port is connected to the power adapter (SPEC: 5.5mm; “positive inside and negative outside icon”) 2. Rj45 interface: Connection supports RJ45 interface devices 3. Power switch: Rocker switch controls power on or off 4. WPS button: Press the WPS button of both modules (set to AP/STA mode, respectively) at the same time, and the two modules will automatically establish a connection. 5.
Product Installation 2. Turn on the power switches of the camera and this product. PT-WC-G1 Installation Instructions (point-to-point mode, webcam usage example) 1. Connect the two devices with the network cable to the webcam and the computer, respectively. Since the Wi-Fi is bidirectional, the two ends can be exchanged arbitrarily without distinguishing between transmitting and receiving. 3. Wait for 30~60s.
Product Specifications Indicator Description Item indicator Status Mode Steady on Power supply is normal off Power is abnormal Power indicator Wi-Fi connection indicator Steady on Blinking PT-WC-G1 Model Wi-Fi connection succeeds Wi-Fi connection fails PT-WC-G1 Frequency Video communication system 5.15-5.25(GHz);5.725-5.85(GHz) MIMO Modulation Frequency stability bandwidth Standard protocol Receiving sensitivity Antenna mode OFDM ±20PPM 40MHz 802.
PT-WC-G1 Setup Instructions Point-to-Point Connection Mode Our factory default connection is generally based on the AP+STATION connection 2. Select Wireless in the Config option on the menu page to modify the corresponding options, where ESSID can be specified by itself (AP and STATION should be consistent and case-sensitive), Encryption and Passphrase can also be specified by themselves. In addition, ensure that the settings of the APs and STATIONs to be connected are consistent.
Cascade Mode Note: In some cases, a longer transmission distance may be required. At this time, we can use the cascade mode based on WDS technology. In this case, you need to set the cascaded devices to AP mode, fix Channel to be 1. Cascading will reduce the bandwidth of the system. It is recommended to cascade up to Level 3. 2. The IP address and MAC address of the device can be found under the Config-Networking page. consistent (i.e.
2. Username: admin; password: admin; click LOGIN to log in. Mode Settings 1. The product can be set to AP or STA mode. After its IP address is logged in through the WEB, select “wireless” under “config” and click Device Mode to select between AP and STA modes. 3. Select “networking” under “config” to change the IP. Click the “Save” button below to save the changed IP. 15 2. During mode switching, the product is changed either from AP mode to STA mode or from STA mode to AP mode through this option.
Product Pairing 4. After clicking CVW001, AP: CVW001 Passphrase will pop up. After entering the password “12345678”, click “connect”. 1. You can only pair with the AP in STA mode. 2. After the IP address of the product is logged in through the WEB, select “wireless” under “config” and click “Scan AP” to scan the AP. 5. After waiting for 1min, refresh the page. You can see that the ESSID is “CVW001”, indicating that the AP with the SSID of CVW001 has been successfully paired. 3.
Product Software Upgrade 1. After the IP address of the product is logged in through the WEB, select “Upgrade” under “System”. 2. After selecting software upgrade under “Choose a file”, click “Upgrade” to upgrade. After clicking, wait for 2min, then refresh the page and log in again.
FCC Statement 3. After waiting for 2min, refresh the page and log in again, you can see the upgraded software version. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
