User's Manual

ManualsBrandsHARTING ManualsElectronicsrMICA-master (USB RF Receiver)

Motor Condition Monitoring System Manual: Wireless Hardware

1 / 9

Motor Condition Monitoring System

User Manual (wireless hardware, US model)

USB wireless base station, wireless sensor box, acceleration sensor

rMICA-master, rMICA-vibration, sMICA-ACC

Ver. 2.0: December 12, 2020

Summary of content (9 pages)

PAGE 1
Motor Condition Monitoring System Manual: Wireless Hardware Motor Condition Monitoring System User Manual (wireless hardware, US model) USB wireless base station, wireless sensor box, acceleration sensor rMICA-master, rMICA-vibration, sMICA-ACC Ver. 2.
PAGE 2
Motor Condition Monitoring System Manual: Wireless Hardware For safety: For safety use, please read and observe the following contents.  The intended users This product has been developed for who in charge of building and maintaining production line. We ask that those have the experience in installing and using the industrial equipment to set up and use this product.  Disassembly of product Please never disassemble or process this device case.
PAGE 3
Motor Condition Monitoring System Manual: Wireless Hardware FCC CAUTIONS:  This device complies with part15 of the FCC Rules. Operation is subject to the following two conditions: i. This device may not cause harmful inference, and ii. This device msut accept any interference received, including interference that may cause undesired operation.  Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
PAGE 4
Motor Condition Monitoring System Manual: Wireless Hardware 1 Device configuration Wireless motor condition monitoring system consists of the following devices. i. Acceleration sensor probe: sMICA-ACC ii. sMICA-ACC has two built-in MEMS accelerometers (1 axis high frequency + 3 axis) and temperature sensor. The probe is installed directly on the object to be measured (Motor, etc.). sMICA-ACC supplies power and sends sensor signals via a dedicated M8 connector cable (2m).
PAGE 5
Motor Condition Monitoring System Manual: Wireless Hardware measurement at the time set on the host computer WEB GUI (up to 10 times/day). In the measurement, the 16384 sets of acceleration is continuously acquired with a sampling interval of 50μs (2kHz) to transmit the data to rMICAmaster. It takes about 5s to send all data. Depending on the signal condition, it may take longer to resend the data.
PAGE 6
Motor Condition Monitoring System Manual: Wireless Hardware v. Host computer We offer the following products as the host computer for this Motor Condition Monitoring System. Web GUI application is already installed in offered host computer products. - Industrial Raspberry Pi MICA-R series - Industrial box PC Both products are customizable. Please feel free to contact us. 2 Installation and wiring i.
PAGE 7
Motor Condition Monitoring System Manual: Wireless Hardware iii. rMICA-master rMICA-master sensor base station is also installed in a place with good visibility to rMICA-vibration. Installing the base station at a high place stabilizes the radio wave condition. Connect the antenna to the antenna connector and tighten it until the ring does not turn.
PAGE 8
Motor Condition Monitoring System Manual: Wireless Hardware 5 Battery rMICA-vibration has a special built-in large capacity and long-life battery. It is primary battery and cannot be charged. We also provide the replacement batteries as option parts. The lifetime of battery is depending on measurement frequency and environmental condition greatly. We can calculate an approximate life value. 0.
PAGE 9
Motor Condition Monitoring System Manual: Wireless Hardware iii. - Battery: 3.6V, 13.5Ah - Mounting: 4 x M4 screw - Housing: ABS Flame retardance - Protection: IP65 - Size: W122 x H31 x D 69.5(mm) - Operating temperature: -10 to 60℃ USB Wireless reciever: rMICA-master - Wireless standard ISM902-928MHz (FCC certified) - Wireless channel: Automatically selected - wireless output(Module): 20mW - Antenna: Non-directional 5dBi, RMA Male - Host connection: USB2.