Operator’s Manual MM23016 Rev.
MM23016, Rev. J MANUAL REVISION HISTORY REV DATE REASON FOR CHANGE - Nov/06 Initial release. A Jun/07 Included EDACS, Conventional, and P25 operation and updated OpenSky operation. B Sep/07 Included MPE information for motorcycle installations and added antennas. C Apr/08 Updated OpenSky operation information. Added P25 Trunking. D Jul/08 Updated OpenSky operation; included CH-721 keymaps, lock/unlock keypad, added Client Mode, included error messages.
MM23016, Rev. J TABLE OF CONTENTS Page 1 SAFETY SYMBOL CONVENTION.................................................................................................... 9 2 RF ENERGY EXPOSURE INFORMATION ................................................................................... 10 2.1 RF ENERGY EXPOSURE AWARENESS, CONTROL INFORMATION, AND OPERATION INSTRUCTIONS FOR FCC OCCUPATIONAL USE REQUIREMENTS .............................. 10 2.1.1 Federal Communications Commission Regulations...............
MM23016, Rev. J TABLE OF CONTENTS Page 7.16 7.17 7.18 7.19 7.20 7.21 7.22 7.23 7.24 7.25 7.26 7.27 7.28 7.29 7.30 7.31 7.32 7.33 7.34 7.35 7.36 8 4 CHANGE THE ACTIVE PROFILE........................................................................................... 33 ENABLE/DISABLE VOLUME SIDE TONE............................................................................ 33 CHECK OR CHANGE THE SELECTED TALK GROUP .......................................................
MM23016, Rev. J TABLE OF CONTENTS Page 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 9 CH-721 FRONT PANEL COMPONENTS ................................................................................ 50 8.2.1 Primary Functions (Quick Access) ................................................................................ 52 8.2.2 Keypad Lock/Unlock..................................................................................................... 52 SELECTION MODE RULES...............................................
MM23016, Rev. J TABLE OF CONTENTS Page 9.12 9.13 9.14 9.15 9.16 9.17 9.18 9.11.1 Receive and Respond to an Individual Call................................................................... 73 9.11.2 Call Storage Lists........................................................................................................... 74 9.11.3 Send an Individual Call ................................................................................................. 74 SCAT OPERATION ...............................
MM23016, Rev. J TABLE OF CONTENTS Page 11.1 11.2 11.3 11.4 11.5 11.6 11.7 RADIO STATUS ICONS ........................................................................................................... 93 MESSAGES................................................................................................................................ 94 ALERT TONES .......................................................................................................................... 96 MENU .....................
MM23016, Rev. J TABLE OF CONTENTS Page Table 8-4: Current Cryptographic Key Display............................................................................................. 59 Table 9-1: Icons and Descriptions ................................................................................................................. 62 Table 9-2: Display Messages ......................................................................................................................... 63 Table 9-3: Alert Tones ....
MM23016, Rev. J 1 SAFETY SYMBOL CONVENTION The following conventions are used throughout this manual to alert the user to general safety precautions that must be observed during all phases of operation, service, and repair of this product. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture, and intended use of the product.
MM23016, Rev. J 2 2.1 RF ENERGY EXPOSURE INFORMATION RF ENERGY EXPOSURE AWARENESS, CONTROL INFORMATION, AND OPERATION INSTRUCTIONS FOR FCC OCCUPATIONAL USE REQUIREMENTS Before using your mobile two-way radio, read this important RF energy awareness and control information and operational instructions to ensure compliance with the FCC’s RF exposure guidelines.
MM23016, Rev. J 2.2 COMPLIANCE WITH RF EXPOSURE STANDARDS Your Harris M7200 mobile two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to RF electromagnetic energy. This radio complies with the IEEE and ICNIRP exposure limits for occupational/controlled RF exposure environment at duty factors of up to 50% talk-50% listen and is authorized by the FCC for occupational use.
MM23016, Rev.
MM23016, Rev.
MM23016, Rev.
MM23016, Rev. J 2.2.2 Mobile Antennas for Motorcycle Installations This device must not be co-located or operated in conjunction with any other antenna or transmitter. Table 2-2: Rated Power and Recommended Minimum Safe Lateral Distances for Motorcycle Application ANTENNA PART NUMBER LE-OM806HDBKTNCDS ANTENNA DESCRIPTION 800 MHz; 3.5 dBd Gain RECOMMENDED SAFE MINIMUM LATERAL DISTANCE FROM TRANSMITTING ANTENNA CONTROLLED UNCONTROLLED 7.9 Inches (20 Centimeters) 16.
MM23016, Rev. J 3 OPERATION SAFETY RECOMMENDATIONS 3.1 TRANSMITTER HAZARDS The operator of any mobile radio should be aware of certain hazards common to the operation of vehicular radio transmitters. A list of several possible hazards is given: Explosive Atmospheres – Just as it is dangerous to fuel a vehicle with the motor running, similar hazards exist when operating a mobile radio. Be sure to turn the radio off while fueling a vehicle.
MM23016, Rev. J 4 OPERATING RULES AND REGULATIONS Two-way FM radio systems must be operated in accordance with the rules and regulations of the local, regional, or national government. In the United States, the M7200 mobile radio must be operated in accordance with the rules and regulations of the Federal Communications Commission (FCC). As an operator of two-way radio equipment, you must be thoroughly familiar with the rules that apply to your particular type of radio operation.
MM23016, Rev. J 5 PRODUCT DESCRIPTION The M7200 mobile is a state-of-the-art radio that operates seamlessly between the 800 MHz frequency band and the 700 MHz frequency band. The M7200 is designed to meet the critical communications demands of public service users and complies with MIL-STD-810F specifications.
MM23016, Rev. J 6 6.1 CHANGE OPERATING MODE CHANGE FROM OTP MODE To change from OTP operating mode to P25, EDACS, or Conventional: 1. Cycle through the menu until the “App Mode” appears in the bottom line of the display. to choose an available mode. Press MENU and confirm (Y/N) with 2. Use MENU again. and press 3. Press the MENU button to confirm. Or Preset button C can be configured via programming to reboot the radio into a particular application mode.
MM23016, Rev. J 7 OPENSKY OPERATION Refer to MM-011553-001 for M7200 V-TAC operating instructions. 7.1 CH-721 FRONT PANEL COMPONENTS The front panel of the control head includes a dot matrix display, controls for menu navigation, an emergency button, three pre-set buttons, a Power On-Off/Volume Control knob, and a microphone connector. In addition, the system model control head features a DTMF keypad. Table 7-1 lists all default front panel controls and their functions.
MM23016, Rev. J Table 7-1: Front Panel Default Controls and Functions PART FUNCTION Power OnOff/Volume Control Knob Turn knob clockwise to power on the radio and increase volume. Mic Connection Connection for hand-held, hands-free, speaker-mic, or headset. Turn counter-clockwise to decrease volume and power off the radio.
MM23016, Rev. J 7.2 POWER UP AND VOLUME CONTROL 7.2.1 Power Up 1. Rotate the Power On-Off/Volume Control knob clockwise to power on the radio. The display illuminates when the radio powers up. 2. Wait for the power-up sequence to complete, which takes approximately ten (10) seconds. During this time, if enabled for auto registration, the radio is provisioned with a customized user personality designed for the user’s specific needs by the OpenSky network administrator.
MM23016, Rev. J The User ID may be remembered from the previous login. (Refer to Section 7.5 for further details regarding log off commands.) The password is established before the radio is put into operation. Contact the local OpenSky network administrator for more information. If necessary, contact radio system administration personnel for login assistance and/or radio-specific login instructions. 7.5 LOG OFF THE NETWORK The *0## command de-registers the radio.
MM23016, Rev. J Figure 7-3: Typical Display 7.8 RADIO STATUS ICONS Status Icons indicate the various operating characteristics of the radio. The icons show operating modes and conditions (see Table 7-2). The location of icons on the display may vary depending on configuration. Table 7-2: Icons and Descriptions ICON DESCRIPTION Indicates data registration. Volume bars – indicates relative volume level. 7.
MM23016, Rev. J MESSAGE DESCRIPTION MDISBSY The MDIS is busy. If condition persists in strong signal conditions, contact your system administrator. DUP IP Duplicate IP. BADIKEY Invalid infrastructure public key sequence number (IPKSN). BADEKEY Invalid end-system public key sequence number (EPKSN). UNK MES Unknown mobile end system (MES). If condition persists in strong signal conditions, contact your system administrator. NOAUT05 MDIS failed mutual authentication.
MM23016, Rev. J 7.11 MESSAGE DESCRIPTION NOAUTHV VNIC does not support or failed mutual authentication. If condition persists in strong signal conditions, contact your system administrator. PLS LOGIN If enabled and authorized for encryption (P7200 only), the radio requires the user to enter a User ID and password. Login with keypad. BAD PWD An invalid password has been entered. Verify the password and re-enter. OVER_TEMP The radio may be too hot.
MM23016, Rev. J Profile 1 Profile 2 Profile 3 TG a TG d TG a TG b TG e TG d TG c TG f TG g TG x TG h TG y TG i TG z TG = Talk Group Figure 7-4: Personality Structure Example If Global Profile is enabled by the system administrator, the number of available talk groups to scan doubles. 7.11.2 Talk Groups A talk group represents a set of users that regularly need to communicate with one another. There can be any number of authorized users assigned to a talk group.
MM23016, Rev. J 7.12 ALERT TONES The M7200 radio also provides audible Alert Tones or “beeps” to indicate the various operating conditions (see Table 7-3).
MM23016, Rev. J 7.13 BASIC MENU STRUCTURE Table 7-4 illustrates the basic M7200 OpenSky menu structure. Menu items vary depending upon system programming, radio hardware, and optional configurations. All menus except the dwell display menu can be turned off by network administration personnel. Table 7-4: Basic Menu Structure MENU NAME RADIO DISPLAYS To/From Dwell Display USAGE NOTES , CLR, or OPT Engineering Display bit-error rates and RSSI data Displays radio system connection data.
MM23016, Rev. J MENU NAME RADIO DISPLAYS See Previous Page Selected Channel “ChannelMenu” USAGE NOTES Allows the user to display and change the current channel. Press MENU to return to dwell display. , CLR, or OPT Scan Mode “ScnModeMenu” Use to select scan mode (Normal, No Scan, or Fixed). Press MENU to return to dwell display. , CLR, or OPT Talk group Lock Out “LockOutMenu” to choose a talk group for locking/unlocking. Press MENU Use to toggle “<” on (locked out) and off.
MM23016, Rev. J 7.14 DUAL-TONE MULTI-FREQUENCY Dual-Tone Multi-Frequency (DTMF) is the system used by touch-tone telephones. DTMF assigns a specific tone frequency to each key so a microprocessor can easily identify its activation. The radio supports DTMF with a system model control head (Figure 7-1). This allows for specific tasks such as entering a user ID and password, or selective calling. When a key on the DTMF keypad is pressed, the DTMF tone is played through the radio’s speaker. 7.15 KEYPAD 7.
MM23016, Rev. J 7.15.2 Quick Buttons (System Model Only) Quick Keys are a two-button sequence that gives the radio user quick access to certain menu items. Quick keys act as a toggle function. Table 7-6: Quick Button Functions QUICK KEYS 1# 2# 3# 4# FUNCTION Transition to ECP mode. If ECP is not loaded in the radio, the radio displays “No App.” Stealth Mode On/Off. Scan Mode On/Off. If the Scan Mode is Normal when the Scan Mode is toggled Off, the Scan Mode is Normal when toggled On again.
MM23016, Rev. J 7.16 CHANGE THE ACTIVE PROFILE The radio can store up to sixteen (16) standard profiles, one of which is the currently active profile. To change the currently active profile: 1. Scroll through the menu until “ProfileMenu” is displayed. 2. Use to scroll through the list of available profiles. 3. Profile becomes active when selected for longer than two (2) seconds, when the MENU is pressed, or when the menu is changed. 7.
MM23016, Rev. J 7.20 STEALTH MODE For some users, it is important to be able to turn off the radio’s display lights, button backlighting, volume and side tones, but not the radio traffic. For example, in covert operations, lights and sounds could inadvertently expose an otherwise unobservable radio user. For this purpose, the radio has a Stealth feature that disables the radio display light, indicator light, and audible side tones.
MM23016, Rev. J 7.22 CHANGE OPERATING MODE 1. Scroll through the menu until “App Mode” appears in the bottom line of the display. to choose an available mode. Press MENU and confirm (Y/N) with 2. Use MENU again. and press Or Preset button C can be configured via programming to reboot the radio into a particular application mode. Or Quick Button command 1# transitions the radio to ECP mode. If ECP mode is not loaded in the radio, the radio displays “No App.” 7.
MM23016, Rev. J 2. If required, login to the network using a user ID and password (see Section 7.4). 3. Select the desired talk group for transmitting on. 4. Press and hold the Push-to-Talk (PTT) button on the hand-held microphone, pause for a moment, and then speak normally. For maximum clarity, hold the microphone approximately 1 ½ inches from the mouth and do not shout or whisper into it. If the call is queued by the network, wait for the grant tone to sound before speaking. 5.
MM23016, Rev. J 7.26 TALK GROUP LOCK OUT There are two ways of focusing voice communications by suppressing calls from talk groups in the currently active profile: 1. No Scan. By turning scan off (selecting “No Scan” via the “ScnModeMenu”), only the selected talk group is audible. 2. Lock Out. By locking out selected talk groups, the “chatter” of the locked out talk groups cannot be heard. This focuses the user’s scanning resources to calls only on desired talk groups.
MM23016, Rev. J 2. Use to scroll through the list of talk groups, if any, until the talk group desired for unlocking appears in the top line of the display. A less-than symbol (“<”) appears next to the name of a talk group that is currently locked out. 3. Press the MENU button to unlock the talk group. The less-than symbol (“<”) next to the name of the talk group disappears. The dwell display appears as soon as the radio acknowledges the selection. 7.
MM23016, Rev. J 7.27.2 Scan Priority The following lists the scanning priority order (from highest to lowest): 1. System All Call 2. Selected talk group in emergency state 3. Default emergency group in emergency state 4. Selected talk group 5. Emergency capable group in emergency state 6. Priority 1 talk group 7. Priority 2 talk group 8. Other (non-priority) 7.27.
MM23016, Rev. J STATUS MESSAGE Disconnect Network Err Reject Unavailable Calling Connecting Hangup Lim 10 min Timing Out Sel Call DEFINITION Selective/PSTN call was terminated for unknown reason. Selective/PSTN call cannot continue because of an unspecified network error. Peer or this user declined request to establish selective/PSTN call. Peer cannot be reached for selective/PSTN call. Calling peer (i.e., for selective or PSTN calls). Establishing selective/PSTN call with peer.
MM23016, Rev. J 4. To end the call, press the # button or (-) using . 7.28.3 Receive a Selective Call When someone calls in from another radio using the selective call function, a ring sounds in the speaker or any number key to accept an incoming Selective Call. and/or headset. Press up or down using Press the microphone’s PTT button when speaking (transmitting) to the caller. Press the # button or (-) using to reject an incoming Selective Call.
MM23016, Rev. J example) are the same as this radio’s numbers, these digits do not need to be entered. Leading zeros can also be ignored. Refer to Section 7.14. 3. Press the # key to enter the number. Choose and Send the Message After specifying the destination radio’s User ID (Section 7.29.1), the radio automatically allows you to choose a message. The current message scrolls across the top line of the display. To choose a message: . The next available message in the list is displayed. 1.
MM23016, Rev. J 3. To delete the message currently being viewed, press the MENU button. Delete Received Messages To delete a received message: 1. Display the message. 2. Delete the message by pressing the MENU button. 3. Confirm the deletion by pressing the MENU button again. 7.29.3 Define Pre-Programmed Messages All selective alert messages are pre-defined by the radio system’s maintenance personnel. These messages are sometimes referred to as “canned” messages.
MM23016, Rev. J transmits audio for a period of time even when the microphone’s PTT button is not pressed. An emergency talk group is provided greater priority and infinite hang-time by the radio system’s infrastructure. Hang-time is the maximum duration of quiet time between transmissions on the talk group before the infrastructure assets are automatically taken away. Because an emergency call is handled on a talk group, it is received by all radios and consoles monitoring the talk group.
MM23016, Rev. J 7.31.3 Clear an Emergency Call or Alert Check with the system administrator to ensure that the radio is programmed to allow an emergency to be cleared. If enabled via programming, clear an emergency by: 1. Pressing and holding the CLR/CLEAR button and simultaneously pressing the emergency button. 2. After the Emergency Cleared Tone sounds, release both buttons. If the radio is in stealth mode, clearing the emergency takes the radio out of stealth mode. 7.31.
MM23016, Rev. J 7.31.5 Dismiss an Emergency Call An emergency is dismissed for a configurable amount of time only (default = 5 minutes). To ignore an emergency call declared by another radio user: 1. Scroll through the menu until “EmgDismiss” appears in the display. until the talk group in the emergency state appears, as indicated by an asterisk (*) 2. Press following the talk group’s name. 3. Press the MENU button. The emergency dismiss timer is cleared when the emergency is cleared. 7.
MM23016, Rev. J The key must be pre-determined by the users prior to making a manually encrypted call on a talk group and is entered into the radio using the keypad. For 128 bit encryption, this key is between 1 and 16 digits. For 256 bit encryption, this key is between 17 and 32 digits. If two communicating radios have different (manually-defined) keys, receive audio at each radio sounds garbled.
MM23016, Rev. J Presets are saved and restored to/from non-volatile memory. Changing the User ID (login in as a different user) clears the presets since they are stored on a per-user basis. Changing control heads does not recall presets for the previous control head. Preset button C can be configured via programming to reboot the radio into a particular application mode. Contact your system administrator to determine if this feature is enabled in your radio. 7.
MM23016, Rev. J 4. Using , scroll until “Manual Select Chan” is displayed and press MENU. 5. Using , scroll to edit the right-most digit and press MENU to advance to the next digit. Repeat until the desired channel is entered. 6. The radio then prompts the user to edit the band. Use to edit the number assigned to the frequency band and press MENU to confirm and enter the SOI mode. Use the Client Mode menu to return to normal operation (Network Mode).
MM23016, Rev. J 8 8.1 P25/EDACS/CONVENTIONAL COMMON OPERATION TURN THE RADIO ON Rotate the POWER ON-OFF/VOLUME knob clockwise, out of detent to turn the radio on. A short beep (if enabled through programming) indicates the radio is ready for operation. The display indicates, if programmed, the last selected system name on line 1 and the last selected group or channel name on line 2. 8.
MM23016, Rev. J Button function may vary depending upon system programming, radio hardware, and optional configurations. Complete the table in Section 14 if the keys have been remapped to provide new functions. Table 8-1: Front Panel Default Controls and Functions PART FUNCTION Power OnOff/Volume Control knob Turn knob clockwise to power on the radio and increase volume. Mic Connection Connection for hand-held, hands-free, speaker-mic, or headset.
MM23016, Rev. J PART FUNCTION GRP Used to enter the Group select mode. STS Permits the transmission of a pre-programmed status message to an EDACS site. MSG Permits the transmission of a pre-programmed message to an EDACS site. PHN Used to place telephone calls through the radio by selecting the interconnect special call function. DIS Used to adjust the current display intensity and the keypad backlight level.
MM23016, Rev. J After entering a selection mode, the following generic display format appears: XXXXXXXX YYY = ZZZ Line 1 shows the currently selected item name (XXXXXXXX) from the list. Line 2 indicates the list (YYY) that the selection is to be made from and the number of the selected item (ZZZ) within the list. (In some cases the information on lines 1 and 2 are exchanged.) Enter the system selection mode by pressing the SYS key.
MM23016, Rev. J 8.5 FEATURE ENCRYPTION DISPLAY Feature Encryption Display is available through the menu function and, if programmed, appears in the menu as “FEATURES.” This data indicates current features programmed into the radio as well as information required to add features to the radio. Once the feature has been accessed, all normal menu functions work. The user can scroll up or down through all of the entries.
MM23016, Rev. J Number Fields Example: These number fields show the set limits of the user's radio as: SG# XXX - Maximum number of system/groups combination available. SY# XXX - Maximum trunked system limit. CH# XXX - Maximum number of conventional channels available. The user needs to know the limits of his radio before attempting to enable other features. The numbers shown here are for example only. 8.5.3 Features Enabled These numbers indicate which features are enabled.
MM23016, Rev. J FEATURE NUMBER 8.
MM23016, Rev. J 8.6.2 Group and Channel Selection Several methods, some of which depend on programming, can be used to select a new group or channel. These procedures assume starting from the normal receive display. 8.7 METHOD 1: If group selection is programmed to the SYSTEM/GROUP/CHANNEL knob, select a group by turning the SYSTEM/GROUP/CHANNEL knob to the desired group. The display registers the new group name on line 2.
MM23016, Rev. J 8.8.2 Clear Modes In Clear Mode, the radio transmits and receives only clear (analog) voice signals. These analog signals are non-digitized and non-encrypted. Clear Mode transmissions can easily be monitored by unauthorized persons. Groups or channels programmed for clear operation cannot transmit or receive unencrypted digital or private messages. 8.8.3 ProVoice Digital Mode ProVoice digital mode allows the radio to transmit and receive digitized voice signals.
MM23016, Rev. J 8.8.4 ProVoice Private Mode ProVoice private mode allows the radio to transmit encrypted messages and receive clear or private transmissions. The radio transmits private if the group/channel is programmed for private operation and forced operation is pre-programmed. If the radio was pre-programmed for auto-select, the radio transmits in the following modes; If Private mode is enabled, transmissions are always in private mode.
MM23016, Rev. J 8.8.5 Private Operation 8.8.5.1 Receive an Encrypted Call When receiving, the radio automatically switches between clear or private operation. If the transmission being received is an encrypted transmission, it is decrypted, the receiver unsquelches and the message are heard in the speaker. The selected group or channel must be programmed for private operation and the correct cryptographic key must be loaded into the radio for this to occur. 8.8.5.2 Transmit an Encrypted Call 1.
MM23016, Rev. J 8.8.6.2 Channel Guard Channel Guard encode is transmitted on analog clear channels only. Channel Guard decode operates on either a clear or private channel. The exception is when G-STARTM signaling is used (see G-STAR paragraph). 8.8.6.3 G-STAR When G-STAR is programmed on a private channel, the radio transmits G-STAR in clear mode and then switch to private for the voice portion of the call.
MM23016, Rev. J 9 9.1 EDACS AND P25 TRUNKED OPERATION RADIO STATUS ICONS Status icons are indicators that show the various operating characteristics of the radio. Figure 9-1: Typical Display Table 9-1: Icons and Descriptions ICON DESCRIPTION Indicates the EDACS system is in Failsoft™ mode (if enabled through programming). Indicates selected group or channel is in scan list. Indicates selected group or channel is programmed as Priority 1 in scan list.
MM23016, Rev. J Table 9-2: Display Messages MESSAGE NAME DESCRIPTION QUEUED Call Queued Indicates the system has placed the call in a request queue. SYS BUSY System Busy Indicates the system is busy, no channels are currently available, the queue is full or an individual call is being attempted to a radio that is currently transmitting. DENIED Call Denied Indicates the radio is not authorized to operate on the selected system.
MM23016, Rev. J MESSAGE NAME Displayed when the menu key is pressed and remains displayed in line 1 until a menu item is selected. MENU SYS=1-64 System = 1 - 64 The system number for the current base station of the system displayed in line 1. It is displayed in line 2 of the display. Press the system key to obtain this display. GRP=1-64 Group = 1 - 64 The group number of the group displayed in line 2 of display. It is displayed in line 1 of the display. Press the group key to obtain this display.
MM23016, Rev. J MESSAGE GRP KEY NAME DESCRIPTION Displayed on line 1 of the display in the display key mode of the menu for trunked systems only. It is followed in the second line with a key number “KEY = <1..7>.” Group Key KEY=1-7 Displayed on line 2 of the display in the display key mode of the menu for conventional systems when the “SYS KEY” or “CHN KEY” is displayed in line 1 and for trunked systems when the “SYS KEY” or “GRP KEY” is displayed in line 1.
MM23016, Rev. J NAME TONE DESCRIPTION Page (P25 T Only) Three high-pitched tones. Out of Range One low pitched. 9.4 In P25 trunked mode, if the receiving radio accepts a page, both the receiving and transmitting radios emit three high-pitched tones. Indicates the radio is in Wide Area Scan. Radio periodically beeps when in Wide Area Scan. MENU The menu function accesses features that are not available directly from the keypad.
MM23016, Rev. J Table 9-4: Menu Item Information FEATURE DISPLAY PARAMETER SETTINGS COMMENT Contrast Adjust Menu Item: CONTRAST Once selected: CNTRST= 1, 2, 3, 4, 5, 6, 7, 8 Selects the Contrast level. Radio Revision Information Menu item: REVISION Informational displays only (see radio); no user selectable settings. Selects the information display to view.
MM23016, Rev. J FEATURE PARAMETER SETTINGS COMMENT External alarm #2 Menu item: EXTALRM2 System and group selection Menu item: SYSGRP 1 Menu item: SYSGRP 2 Menu item: SYSGRP 3 Menu item: SYSGRP 4 Menu item: SYSGRP 5 Mute Menu item: MUTE ON, OFF Mute #1 Menu item: MUTE 1 ON, OFF Mute #2 Menu item: MUTE 2 ON, OFF Multiple radio operation Menu item: RADIO ON, OFF Toggles the currently selected radio.
MM23016, Rev. J 2. Press and hold the PTT button. The radio displays the system and group names and performs the necessary signaling required to obtain a communication channel. 3. When the working channel is assigned, TX and BSY indicators are turned ON and a short beep is sounded indicating communication can begin. If two or more tones, or a high-pitched tone is heard, the system may be busy and the call request has been placed in queue or the request has been denied for some reason.
MM23016, Rev. J 2. When the working channel assignment is received, the radio sounds a single beep (Autokey alert tone) indicating it is ready for voice transmission. *TXEMER* flashes on line 2 in the display until the emergency is cleared. 3. Press PTT and speak into the microphone in a normal voice. 4. Release PTT when the transmission is complete and listen for a reply. 5.
MM23016, Rev. J 9.9.4 When Wide Area System Scan Is Enabled If the radio cannot find the control channel of the selected system and begins Wide Area System Scan (WA Scan), the radio only scans for the priority system control channel if the priority system is in the WA Scan list. 9.9.5 When ProScan Is Enabled The radio monitors the priority system and switches to the priority system if the priority system meets the criteria defined in the “ProScan Options” dialog box.
MM23016, Rev. J 9.10.1 Add Groups to a Scan List 1. With scan operation turned off, select the desired group to add to the selected Trunked system group scan list. 2. Press (+) or (-) with period. to display the current priority status of the group on line 1 for a time-out 3. While the status is displayed, press (+) with 4. Press (+) with to add the group to the scan list. a second time to set the group to Priority 2. is displayed. is displayed. 5.
MM23016, Rev. J Pressing up with when scan is on causes the radio to recall the scanned group that was last received. This group is recalled for a period equal to the scan hang time. 9.10.5 Priority Group Scanning When scan is enabled and the Priority 1 and Priority 2 groups have been identified, the radio listens to calls on those groups and the selected group.
MM23016, Rev. J To access the list, press the IND key twice. Use display the time elapsed since the call was received. to scroll through the list. Press the MENU key to 9.11.2 Call Storage Lists There are two lists available for call storage in the radio, the calls received list (1-10) and the personality list (1-99 as defined by the user). When the individual call mode is entered by pressing IND, the calls received list is available.
MM23016, Rev. J apply. While in the individual call list, the menu key toggles the display between the call name and the unit ID number. If the individual is not stored in this list but the individual’s unit ID is known, it can be entered directly from the keypad. 2. Press the PTT button; the radio performs the necessary signaling to obtain a communication channel. When the signaling is complete and the radio is clear to transmit, TX indicator turns ON and the channel access tone sounds.
MM23016, Rev. J The M7200 mobile radio is capable of half-duplex conversation only. The caller’s message can only be sent if the PTT button is pressed (the radio is transmitting) and the caller can only be heard by the person being called when the PTT is released (the radio is receiving). 9.13.
MM23016, Rev. J 3. Enter the desired number. If necessary, a pause can be entered by pressing and holding 0-9, (*), or (#) until an underscore appears in the display. The individual call list entries accepts up to 5 digits. The phone call list entries accept a combination of up to 31 digits and pauses. 4. Press and hold MENU until the display changes indicating that the number has been stored. 5. Repeat the steps above if the number stored in an entry location needs to be changed. 9.
MM23016, Rev. J 9.14.3 DATA ON Operation The data state is enabled by one of the following (depending on how it was disabled). “DATA ON” is displayed top line of display for 2 seconds then the display returns to normal. Replacing the microphone into the hookswitch (going on-hook). Only valid if the “DATA OFF” operation was entered by removing the microphone from the hookswitch (going off-hook). Clearing an emergency, but valid only if an emergency caused “DATA OFF” operation. 9.14.
MM23016, Rev. J initiated when needed by the operator. After a pre-programmed time, the radio responds to receive data calls; however, the following conditions clear the data lockout mode: 9.15 The CLR (System Model) or CLEAR (Scan Model) button is pressed. Transmitting a data call. Changing a system. An emergency is declared. Pressing the PTT while in Public Address mode. Turning scan ON with the SCAN button.
MM23016, Rev. J tone sounds and the MSG keylight remains lit. If the site does not receive the message properly, a lowpitched tone sounds and the MSG keylight blinks. If an incorrect message text was selected or the incorrect number button was pressed, the message text can be changed during the pre-programmed time-out period by pressing another number button. The message text selection can also be cancelled by pressing the CLR button prior to the time-out period.
MM23016, Rev. J followed by the logical ID number of the unit being called. If the receiving radio receives the Page and responds, both radios emit three high-pitched tones. The receiving radio also displays PAGE and the ID of the calling radio.
MM23016, Rev. J 10 CONVENTIONAL OPERATION 10.1 RADIO STATUS ICONS Status icons are indicators that show the various operating characteristics of the radio. The icons appear on the first line of the display. Figure 10-1: Typical Display Table 10-1: Icons and Descriptions ICON DESCRIPTION Indicates selected group or channel is in scan list. Indicates selected group or channel is programmed as Priority 1 in scan list. Indicates selected group or channel is programmed as Priority 2 in scan list.
MM23016, Rev. J MESSAGE NAME DESCRIPTION UNKNOWN Caller's ID Not Received T99 ON Type 99 Decode ON Indicates the Type 99 Decode feature is enabled. T99 OFF Type 99 Decode OFF Indicates the Type 99 Decode feature is disabled. PA ON Public Address ON Indicates that the public address function of the radio is enabled. PA OFF Public Address OFF Momentary (2 seconds) indicates that public address function of the radio was disabled.
MM23016, Rev. J MESSAGE PRS NAME 10.3 NAME DESCRIPTION Personality Name Displayed on line 1 of the display under the revision selection of the menu. The personality name is displayed on line 2 at the same time. ALERT TONES The M7200 mobile radio provides audible alert tones or “beeps” to indicate the various operating conditions. These alert tones can be enabled or disabled through programming. Table 10-3: Alert Tones NAME TONE Call Originate A short mid-pitched tone.
MM23016, Rev. J 2. Press the ramp control until the display shows: MENU CONTRAST 3. Press MENU. The contrast menu item is activated and the display is similar to the following: CNTRST = X YYYYYYYY Line 1 shows the active menu item and its current parameter setting (XXX). Line 2 shows the currently selected system or group name (YYYYYYYY). 4. The menu item's parameter setting shown in the display can now be changed by using the ramp control to scroll through the list of parameter values.
MM23016, Rev. J FEATURE DISPLAY COMMENT Menu item: SCAN ADD Once selected: Proper scan icon displayed. Menu item: SCAN DEL Once selected: Scan icon goes out. Menu item: SCAN A/D When selected: Toggles through scan selections Menu Item: SCAN ADD Press twice when actively receiving; three times when not receiving. Scan icon displayed. Menu item: HOME Once selected: Home group or channel displayed. Menu item: SYS SEL Once selected: SYS = n 1-64 = (n)umber of desired system Displays the system selected.
MM23016, Rev. J 3. Select the desired conventional system and channel. The display indicates the current conventional system and channel names. 4. The radio is now ready to receive calls. 5. When the radio receives a call (and the correct encoding is decoded, if programmed and enabled), it unmutes on the channel and the BSY indicator comes on. 10.6 SEND A CALL 1. Turn ON the radio and set the POWER ON-OFF/VOLUME knob to the desired volume level. Select the desired conventional system and channel. 2.
MM23016, Rev. J 10.7.1 Use 5-Tone Signaling to Declare an Emergency If 5-Tone signaling is defined for emergency declaration in place of G-STAR emergency signaling, a preprogrammed tone sequence is transmitted instead of the G-STAR sequence. This emergency declaration functions as the G-STAR emergency in all other respects. 10.7.2 Tone Encode Transmission In conventional mode, two keys can be defined to be tone encode triggers.
MM23016, Rev. J 10.8.1 Add Channels to a Scan List 1. With scan operation turned OFF, select the desired channel to add to the selected conventional system channel scan list. 2. Press (+) or (-) with period. to display the current scan status on line 1 of the display for a time-out 3. While current scan status is displayed, press (+) to add the channel to the scan list. This sets the selected channel for non-priority scanning. 4.
MM23016, Rev. J Pressing the PTT button when scan is ON causes the radio to transmit on the displayed channel or to the currently selected channel depending on programming. Pressing (+) with when scan is ON causes the radio to recall the scanned channel that was last received. This channel is recalled for a period equal to the scan hang time. 10.10 TURN SCAN OFF Toggle the scan operation OFF by pressing SCAN. The radio resumes operation on the selected channel. 10.
MM23016, Rev. J 10.12 TYPE 99 DECODE If the Type 99 Decode Option has been pre-programmed, individual selective calling is possible. The radio can now decode individual, group or supergroup paging calls. Two sets of Type 99 paging codes must be pre-programmed into the radio. When the radio decodes an appropriate Type 99 code sequence, an alert tone and visual indicator is provided to the user. The receiver then operates as a noise squelched unit until Type 99 is reset.
MM23016, Rev. J 10.13 DIRECT MODE OPERATION The direct mode (or talk-around) provides short range, line of sight communications. One of the buttons on the control unit must be pre-programmed for this feature to function. 1. Make sure the radio is ON and then select the desired conventional system and channel. 2. Press the pre-programmed button to toggle the talk-around function ON. 3.
MM23016, Rev. J 11 P25 CONVENTIONAL OPERATION 11.1 RADIO STATUS ICONS Status icons are indicators that show the various operating characteristics of the radio. The icons appear on the first line of the display. Figure 11-1: Typical Display Table 11-1: Icons and Descriptions ICON DESCRIPTION Indicates selected group or channel is in scan list. Indicates selected group or channel is programmed as Priority 1 in scan list. Indicates selected group or channel is programmed as Priority 2 in scan list.
MM23016, Rev. J 11.2 MESSAGES During radio operation, various messages are displayed on either line 1 or line 2. Typical messages include control channel status information, such as system busy or call denied, or messages associated with the radio's operation, (i.e. volume adjust). These messages are described as follows: Table 11-2: Display Messages MESSAGE NAME TALKARND Talk-around Indicates the radio is operating on conventional channels in talk-around mode (no repeater).
MM23016, Rev. J MESSAGE NAME NO ENTRY DESCRIPTION Indicates that there is no data stored in one of the programmable items in either the phone list or individual call list. The user programmable items are items 1 through 10 in each list. INV SYS Invalid System Displayed when the current system is an invalid type. CHN=1-99 Channel = 1 - 99 Displayed on line 1 of the display. This is a conventional channel index displayed when the group key is pressed.
MM23016, Rev. J 11.3 ALERT TONES The M7200 mobile radio provides audible alert tones or “beeps” to indicate the various operating conditions. These alert tones can be enabled or disabled through programming. Table 11-3: M7200 EDACS Mode Alert Tones NAME TONE DESCRIPTION Call Originate A short mid-pitched tone. Carrier Control Timer Five short high-pitched warning tones followed by a long low-pitched tone. Key Press Alert A short tone. 11.
MM23016, Rev. J CNTRST = X YYYYYYYY Line 1 shows the active menu item and its current parameter setting (XXX). Line 2 shows the currently selected system or group name (YYYYYYYY). 4. The menu item's parameter setting shown in the display can now be changed by using the ramp control to scroll through the list of parameter values. Once the desired setting is reached, press MENU to store the value and return to the normal display.
MM23016, Rev. J FEATURE Scan Delete Scan Add/Delete Last Scanned Channel Recall Home channel selection DISPLAY Menu item: SCAN DEL Once selected: Scan icon goes out. COMMENT Deletes channel from scan list. Menu item: SCAN A/D Toggle sequence When selected: Toggles S, 2, 1, S, ... through scan selections Menu Item: SCAN ADD Press twice when actively receiving; three times when not receiving. Scan icon displayed. Menu item: HOME Once selected: Home group or channel displayed.
MM23016, Rev. J 4. When a grant tone is received (if enabled through programming), speak into the microphone. 5. Release PTT and wait for response. 11.5.2 Receive a Group Call The radio unmutes according to the squelch mode defined in the radio personality (monitor, normal, selective). 1. Select the desired P25 system and Talk Group/Channel or turn scan on and make sure the desired channel is in the scan list. 2.
MM23016, Rev. J 11.7 EMERGENCY GROUP CALLS IN P25 MODE There is no method available for a system-wide Emergency clear. An emergency group call must be cleared on each individual radio. 11.7.1 Declare an Emergency Group Call 1. Select the desired P25 system and Talk Group/Channel. 2. Press the red emergency button on the top of the radio. The radio broadcasts a short emergency transmission with the emergency bit set. “TXEMER” appears in the display of the transmitting radio. 3.
MM23016, Rev. J 12 BASIC TROUBLESHOOTING If the radio is not operating properly, check Table 12-1 for likely causes. For additional assistance, contact a qualified service technician. Table 12-1: Basic Troubleshooting SYMPTOM CAUSE SOLUTION Radio will not turn on. No power. Test the connection to the vehicle power supply. Radio will not turn off. If in multiple control head configuration, one of the attached control heads is still powered up. Power off all control heads.
MM23016, Rev. J SYMPTOM Screen displays: NOAUTHV Screen displays: NOAUTHM Screen displays: NOSUPRT Encrypted calls cannot be made. 102 CAUSE SOLUTION Radio authentication of the VNIC failed. Contact system administrator. VNIC authentication of the radio failed. Contact system administrator. The voice authentication security policy is set to only allow authenticated users. Contact system administrator. User not logged in. Log in (refer to Section 7.15.2).
MM23016, Rev. J 13 TECHNICAL ASSISTANCE The Technical Assistance Center's (TAC) resources are available to help with overall system operation, maintenance, upgrades and product support. TAC is the point of contact when answers are needed to technical questions. Product specialists, with detailed knowledge of product operation, maintenance and repair provide technical support via a toll-free (in North America) telephone number. Support is also available through mail, fax, and e-mail.
MM23016, Rev. J 14 KEYPAD REMAPPING If the keys have been remapped to provide new functions, fill in the following template for future reference.
MM23016, Rev.
MM23016, Rev.
MM23016, Rev.
MM23016, Rev.
MM23016, Rev. J WARRANTY Please register this product within 10 days of purchase. Registration validates the warranty coverage, and enables Harris to contact you in case of any safety notifications issued for this product. Registration can be made on-line at www.pspc.harris.com/CustomerService or by contacting Harris Warranty Administration at the following: U.S. & Canada: Phone Number: 1-800-368-3277, Option 4 (toll free) Fax Number: 1-434-455-6821 E-mail: mailto:Jerri.Wilmouth@Harris.
Public Safety and Professional Communications | www.pspc.harris.
