Read all instructions before assembly and use. KEEP INSTRUCTIONS FOR FUTURE USE. ADULT ASSEMBLY REQUIRED Due to the presence of small parts during assembly,keep out of reach of children until assembly is complete. Full Panel 5-in-1 Convertible Crib THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
CAUTION: ANY MATTRESS USED IN THIS CRIB SHALL BE AT LEAST 27 1/4 BY 51 5/8 IN. WITH A THICKNESS NOT EXCEEDING 6 IN. WARNING: . Infants can suffocate on soft bedding.Never add a pillow or comforter.Never place additional padding under an infant. . Failure to follow these warnings and the assembly instructions could result inserious injury or death. DO NOT use this crib if you cannot exactly follow the accompanying instructions. .
TODDLER BED WARNING: INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT. Openings in and between bed parts can entrap head and neck of a small child. NEVER use bed with children younger than 15 months. ALWAYS follow assembly instructions. The maximum user weight is 50Ibs(22.7kg) WARNING STRANGULATION HAZARD NEVER place bed near windows where cords from blinds or drapes may strangle a child. NEVER suspend strings over a bed.
ATTENTION! Respecter les avertissements sur tous les produits du berceau. L'assemblage par un adulte est nécessaire. Les petites pièces peuvent présenter un danger d'étranglement avant l'assemblage. Ci-joint s'il vous plaît trouver les instructions simples, étape par étape pour vous aider à assembler rapidement vos produits. Avant de commencer, nous vous recommandons de suivre les étapes ci-dessous: 1.Lire attentivement les instructions, s'il vous plaît. 2.Identifier toutes les pièces et le matériel. 3.
de transport ou tout autre film plastique pour recouvrir le matelas non vendu et conçus à cette fin, ils peuvent provoquer la suffocation. ATTENTION: Tout matelas utilisé dans ce lit doit être au moins 27-1/4 pouces (690mm) par 51-5/8 pouces (1310mm), avec une épaisseur n'excédant pas 6 pouces (150 mm), les dimensions du matelas doivent être prises de la couture à la couture ou bord à bord dans le cas échéant. Ne jamais utiliser un matelas à eau avec ce produit.
PARTS:MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT. A: Left head board (1 pc) B: Right head board (1 pc) B1 A1 B2 A2 B3 A3 A1:Left back leg (1pc) A2:Left board (1pc) A3:Left front leg (1pc) B1:Right back leg (1pc) B2:Right board (1pc) B3:Right front leg (1pc) C:Top rail (2 pc) E: Back rail bottom (1 pc) J:The bottom bar (1pc) G. Mattress support (1 pc) POUCH ATTACHED TO MATTRESS SUPPORT -KEEP INSTRUCTIONS IN THIS POUCH AFTER ASSEMBLY.
PARTS: HARDWARE KIT SEE FRONT COVER. a.M6x40 Allen head bolt(4pcs) No drills necessary. Do not use power screwdriver b. Wood dowels (11pcs) Phillips Screwdriver (not supplied) c. Allen wrench (1pc) d.M6x75 Allen head bolt (8pcs) e. Barrel nuts (18pcs) f.M6x19 Allen head bolt (4pcs) g.
SECTION 1: Crib Assembly STEP 1 Parts and tools required to complete step. B2. Right board (1pc) A3. Left front leg (1pc) A1. Left back leg (1pc) A2. Left board (1pc ) d.M6x75 Allen head bolt (8pcs) c. Allen wrench (1pc) B3. Right front leg (1pc) B1. Right back leg (1pc) e. Barrel nuts (8pcs) d Attach left back leg (A1) and left front leg (A3) to left board (A2) using M6X75mm bolts ( d) and barrel nuts (e) . Tighten With the M4 Allen Wrench.
SECTION 1: Crib Assembly STEP 2 Parts and tools required to complete step. C. Top rail(1pc) e. Barrel nuts (4pcs) E. Back rail bottom(1pc) From Step 1 b Wood dowels(4pcs) c. Allen wrench g.M6x55 Allen head bolt(4pcs) a.M6x45 Allen head bolt(2pcs) Attach The Top Rail (C) and The Back Rail Bottom (E) to the assemblies from step 1 using Wood Dowels (b), Bolts (a/g),Barrel Nuts (e) .Tighten with the Allen Wrench (c) . Use the Flat Head Screwdriver to hold the Barrel Nut in the proper alignment.
SECTION 1: Crib Assembly STEP 3 Parts and tools required to complete step. f.M6x19 Allen head bolt (4pcs) From Step 2 G. Mattress support (1 pc) c. Allen wrench Attach the Mattress Support (G) in all corners using Bolt (f) in each corner. Tighten with the Allen Wrench. WARNINGS ON POUCH MUST FACE UP B The Warnings printed on the pouch attached to the mattress support must face up, the springs must face up.
SECTION 1: Crib Assembly STEP 4 Parts and tools required to complete step. C. Top rail (1PC) b. Wood dowels(9PS) J. The bottom bar (1pc) From Step 3 F. Front rail bottom(1PC) e. Barrel nuts(8PCS) c Allen wrench a.M6x45 Allen head bolt(2pcs) g.M6X55 Allen head bolt(4PCS) Attach the bottom bar(J) to the front legs by using wood dowels (b),bolts (g),barrel nuts (e). Then, attach the top rail (C) and the front bottom rail (F) to front legs by using wood dowels (b),bolts (a/g),barrel nuts (e).
SECTION 1: Crib Assembly STEP 5 Parts and tools required to complete step. Read all instructions before assembly and use. KEEP INSTRUCTIONS FOR FUTURE USE. 5 in 1 Crib ADULT ASSEMBLY REQUIRED Due to the presence of small parts during assembly,keep out of reach of children until assembly is complete. Assenmbly Instruction Booklet THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE. Store the assembly instrucion booklet in the pouch attached to the mattress support.
SECTION 2: Toddler Bed Conversion STEP 1 Parts and tools required to complete step. c. Allen wrench Finished Crib Remove the Front Rail installed in step 5 of section 1 Crib Assembly.
SECTION 2: Toddler Bed Conversion STEP 2 Parts and tools required to complete step. g.M6x55 Allen head bolt (2pcs) e. Barrel nuts (2pcs) c. Allen wrench SECTION 1 From Step 3 J. The bottom bar (1pc) b. Wood dowels (2pcs) You have the option to convert crib to a day bed 1:Remove The front top rail (J) and The front rail bottom (F) . 2:Install the mattress support (G) in its lowest position. 3.To assemble the bottom bar(J) to the front legs as the image showed.
SECTION 2: Toddler Bed Conversion STEP 3 (The toddler bed guardrail is sold separately.) ! WARNING: SEE PAGE 3 FOR TODDLER BED WARNINGS The mattress support must be in the lowest positions. Store all hardware safely. Read all warnings on page 3. As shown, use as a day bed or love seat sofa. No Not use without stabilizer bar installed. ! Stabilizer bar must be used when converted to a toddler bed. A toddler bed guardrail is available for this crib.
SECTION 3: Full Size Bed Conversion I STEP 1 Parts and tools required to complete step. C. Allen wrench You have the option to convert the crib to a Full Size Bed. Simply follow steps in reverse order to disassemble the crib. Then remove the Rear Legs from the left Crib End and Right Crib END with the M4 Allen Wrench as shown. Store all parts and hardware in a safe place.
SECTION 3: Full Size Bed Conversion I STEP 2 (Hollywood bed frame sold separately) Parts and tools required to complete step. Cross Bar (7PCS) From Section 3 Step 1 Split leg (2PCS) Converting kit is sold separately You have the option to convert crib to a full size bed II 1.Insert the split leg to the left&right side bar . 2.Connect the headboard Leg to the left side bar and the right side bar. 3.Connect the footboard Leg to the left&right side bar. 4.Connect the c to the left&right side bar.
SECTION 3: Full Size Bed Conversion II STEP 1 (Hollywood bed frame sold separately) Parts and tools required to complete step.
LIMITED WARRANTY WARNING: Should this product become damaged, and/or components are broken or missing, DO NOT USE To register your product for important safety alerts and updates to your product please visit our website Please do not return this item to the store before contacting us about missing parts or with any questions.