Owner's Manual

ManualsBrandsHarman ManualsElectronicsHarman SmartAuto TAG2.0

Harman

SmartAuto TAG2.0

Quick Start Guide

Issue 1.0

1 About SmartAuto TAG2.0

2 Product Features

SmartAuto TAG2.0 is an intelligent OBD solution, which

integrates 4G module, GPS, acceleration sensor and ECU

communication module. Developed on Qualcomm chipset and

ST MCU, it can provide vehicle position, collect statistics on

vehicle trajectory, reconstruct driving behavior, collect statistics

on fuel consumption, track vehicle to prevent theft, read

vehicle status, read/clear vehicle fault codes, etc. This OBD

solution is well applicable to individual consumers, ßeet

management, UBI, vehicle rental and vehicle maintenance

1.1 Product Functions

• LTE communications

• Real time vehicle data

• Vehicle DTC code

• GPS/GLONASS/BS/A-GPS positioning

• Supplementary transmission for

• Blind-area data

• Swapping alarming

• FOTA upgrade

• Sleeping and awaking

• Driving behavior analysis

1.2 Package Content

3 How to Install and Start

3.1

Install

When the vehicle is shut down, insert the device into the

OBDII interface. This interface is usually located under the

dashboard of the vehicle and above the accelerator pedal.

If not, refer to the schematic or your owner's manual. If the

installation affects driving, you can purchase the extension

cable and place it in a safe place.

3.2

F irst use

For the f irst use, initialization is required: after inserting the

equipment, start the engine and keep idling for 3-5 minutes

until the equipment works normally (the red and green status

indicator lights are always on). Your device is ready for normal

use!

3.3

LED Indicator

3.4

Platform Operation

Set the dialup prof ile, server IP address, and port

through an SMS message to log in to the server. Then

you can query and set the device parameters.

4 Safety Warning

Please use a battery specif ied by the device manufacturer.

Otherwise, all warranty services are invalid.

The device manufacturer will not provide a warranty for damage

caused by non-OEM accessories.

• Do NOT put the device into water or f ire.

• Do NOT bend or open the battery.

• Do NOT recharge the battery.

• Do NOT disassemble the device. Improper handling might

damage the device permanently.

5 FCC

5.1

Regulatory Requirement

Harman SmartAuto TAG2.0 device complies with Part 15 of FCC

Rules. Operation is subject to the following two conditions: (1)

The device may not cause harmful interference, and (2) The

device must accept any interference received,

including

interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable

protecti

on against harmful interference in a residential

installation. This equipment generates uses and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications.

However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment

off and on, the user is encou

raged to try to correct the

interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from

hat to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for

help.

Any Changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment

5.2

Body-support SAR

This equipment should be installed and operat

ed with a

minimum distance of 1

0 mm between the device and your body.

Features

Description

Developed network

standards

compliant

Developed on Qualcomm

chipset able to operate on

networks of

multiple countries

Wide

operating

voltage range

12V/24V DC power

supply,applicable to different

vehicle models

Driving

behavior

analysis

Built-in acceleration sensor and

gyroscope to collect the

information

about driving behaviors

Complete &

stable

Applications

Device management, position f

ix, vehicle diagnosis, driving

behavior

analysis, and other applications

Various OBD-II

Protocols

• ISO 9141-2, ISO14230-4,

ISO15765-4,

• SAE J1850 VPW (GM vehicles)

• SAE J1850 PWM (Ford vehicle)

• SAE J1939

Operational range

temperature, C°

( full function )

Charge :10 ～45℃ ，Relative

humidity≤75%

Discharge： -20 ～ +55℃ ，Relative

humidity≤75%

Storage

Storage for 30 days: - 20 ℃～ +

50 ℃

Part

Unit

Quantity

TAG2.0 OBD pcs 1

Quick start guide pcs 1

Status

Colour

describe

GPS

Blue

a. GPS disable, the LED will be off

b. GPS “ON“ but location not fixed, the

LED will be Blue Blinking.

c. GPS “ON“

and location fixed, the LED

will be Blue Solid

Wi-Fi

Blue

a. WiFi “OFF“, the LED will be off

b. WiFi “ON“, the LED will be Blue

Blinking

c. WiFi client connected will be solid blue

LTE

Green

/Red

/Blue

a. Modem Off and in Sleep mode the

LED will be off

b. Network connection in progress

LED Blinking Red

c. Network connection successful LED

solid green