Quick-Start Guide
Important! �� WARNING: Operation of any feature of this device while driving could be dangerous. Always be careful and attentive to your vehicle and the traffic around you. Obey all traffic laws and observe safe driving practices. Do not connect or disconnect your portable music player or program the Drive + Play 2 system while driving. Always pull off the road and park in a safe position before browsing your portable music player or adjusting the settings on the Drive + Play 2 system.
Important! Connecting the iPod® Always hold the Drive + Play 2 system’s iPod dock connector by its sides and gently insert (or remove) the dock connector. Never use excessive force to insert or remove the connector, or damage to your iPod may occur. Lost Data About Installation IMPORTANT: The Drive + Play 2 system should be installed according to these instructions and relevant federal, state or local laws and regulations, which the purchaser should determine prior to installation or use.
Choose the Display Location �� See below Select Display Mounting Location Change Display Base Mount only if needed for your chosen mounting location Loosen 3mm screw in center of the base. Move base to the top mounting hole. Tighten screw again to secure base. �� The installation of this device between the driver and the windshield or otherwise in any manner that obstructs the driver’s clear view of the road or traffic conditions is dangerous and may be prohibited by law.
Installing the Display 1 Mounting with Screws 1 Base Hex Screw 2 3 Mounting Plate 1 Place display base onto mounting plate and rotate into desired position. 2 Tighten the hex screw to lock the display base onto the mounting plate. Plug cable into display 3 4 Mounting with Adhesive Pad Align mounting plate to location and attach with 3 screws. Make sure the arrow points toward the front of the car.
Installing the Wireless Control Knob 2 1 Install Control Knob Battery �� 4 Select Control Knob Mounting Location 3 Mount Control Knob Base Orient the base so that the arrow is facing the front of the car. You can either screw the base to the mounting location or use the supplied adhesive pad. If you use the adhesive pad, you must FIRST CLEAN the surface with the supplied alcohol cleaning pad. 6 3 CR2032/DL2032 Use a coin to remove the bottom cover.
Connections to the Cigarette Lighter Hub 1 2 3 Power Indicator 1 Direct Cigarette Lighter Plug-In Plug into vehicle. Options 2 ������ ��� Cigarette Lighter Extension Cable Expansion Port Display iPod Audio Output Audio Output Options 1. If using the built-in wireless FM transmitter, leave the audio output jack empty. YELLOW = Constant source of +12V Detach lighter stalk. Stalk fits tightly. Some force is required to separate.
Wired FM Transmitter Adapter Connections 1 2 3 Connect in the line between vehicle antenna and radio. 1 2 Connect FM Transmitter Adapter to Drive + Play 2 System. 3 Plug the adapter into the back of radio or FM tuner location. Plug the vehicle’s antenna into FM Transmitter Adapter. If your car’s audio system does not provide an auxiliary input and there is no third-party adapter available, use the Drive + Play 2 system’s wired FM Antenna Adapter for the best audio performance.
Using the Control Knob Rotate ring to move the highlight bar on the screen Previous Press and hold to REWIND Show Previous Menu (Press and hold to show special features) Next Press and hold to FFWD Press once to toggle PLAY/PAUSE Press and hold for 2 seconds to turn ON/OFF Press to select the highlighted menu item Note - If Drive + Play 2 is turned off with the bottom button it must be turned back on that way! If the control knob is unresponsive, try pressing the top, center, and right buttons simulta
iPod® Functions 1 2 3 iPod Connection Confirmation When your iPod is successfuly connected, the iPod icon appears in the top-right corner of the display. “iPod” will also appear as the first menu item. iPod Playing Music The Drive + Play 2 system is designed to make navigating the menus on your iPod simple and intuitive. Select menu items using the scroll wheel and press the center button to select. 1 Select “iPod” from source menu.
Connecting USB Devices 1 2 3 USB Drive Connection Confirmation USB Storage Device The Drive + Play 2 system is compatible with USB Flash Memory devices and other USB devices. For a complete list of compatible devices, please visit www.driveandplay2.com. When your USB Drive is successfuly connected, the USB icon appears in the topright corner of the display. “USB Drive” will also appear as the first menu item.
Configuring Audio Playback Wireless FM Transmitter or Wired FM Antenna Adapter If you use the built-in wireless FM transmitter, no additional wired audio connection is necessary. To use the wired FM Antenna Adapter, you will need to wire it into your vehicle’s FM Antenna connection first, then complete these steps. Either way, you must enable and select the FM transmitter frequency to hear audio through your vehicle’s FM radio. Remember, you may try several frequencies for the best result.
Letter Seek 1 2 3 4 This feature allows you to quickly browse alphabetically sorted lists, such as Artist, Playlists and Songs in the iPod. 1 2 Press and hold top menu button in an alpabetically sorted list 3 Turn the ring to advance the letters manually Large letter appears on the screen Artist ABBA Billy Idol Bon Jovi Coldplay A Def Leppard or, press the “Next” or “Previous” buttons to begin automatic scrolling.
Automatic Mix 2 1 3 4 Drive + Play 2 system creates channels automatically, and you can refine the channel content during playback. Choose “More like this” to place a higher priority on songs similar to the current selection. Choose “Less like this” to place a lower priority on songs similar to the current selection. Choose “Play something else” to reprioritize selections to something different than the song that’s currently playing. 1 Select “iPod” and then select “Automatic Mix”.
“Keep playing” / “Jump to” Options This feature allows you to continue playing songs from the current artist or album without leaving the “Now Playing” screen. 1 Keep playing artist Press and hold top menu button during playback. This feature will continue playing the current song, then play the remaining songs by that artist in order. Jump to artist Now Playing This feature will stop playing the current song and begin playing all the songs by that artist in order.
Troubleshooting Troubleshoot problems, download updates, and www.driveandplay2.com For customer and technical support, call 516.255.4545 250 Crossways Park Drive, Woodbury, New York 11797 www.harmankardon.com ©2007 Harman International Industries, Incorporated. All rights reserved Part No. DP2QSGNA001 HDMDP200106 MWC A Harman International Company This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
IC Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.