Installation & Assembly

FAD & SAME THESE Nh H KU
INSTALLATION OPERATION
INSTRUCTIONS
TOOLS & MATERIALS REQUIRED
o Blade screw driver
• Adjustable wrenen
» Step Ladder
e Wire cutters
• Wiring supplies as required by electrical code
CAUTION: Before assembling your lighting fixture, refer to the
section titled ELECTRICAL CONNECTIONS. If you feel you do
not have electrical wiring experience, refer to a do-it-yourself
wiring handbook or have your fixture installed by a qualified
licensed electrician.
GENERAL
1. To ensure the success of the installation, be sure to read these
instructions and review the diagrams thoroughly before begin-
ning.
2. All electrical connections must be in accordance with local
codes, ordinances, or the National Electrical Code. If you are
unfamiliar with methods of installing electrical wiring, secure
the services of a qualified licensed electrician.
3. These fixtures are intended to be mounted to a 4"X2y8" deep
metal octagon outlet box. The box must be directly supported by
the building structure.
4. Before starting the installation, disconnect the power by taming
off the circuit breaker or by removing the fuse at the fuse box.
Turning the power off using the light switch is not sufficient to
prevent electrical shock.
NOTE: The important safeguards and instructions appearing in
this manual are not meant to cover all possible conditions and
situations that may occur. It must be understood that common
sense, caution and care are factors which cannot be built into any
product.These factors must be supplied by theperson(s)caring for
and operating the fixture.
UNPACK THE FIXTURE
Check the contents of the box. You should receive:
8
Mounting hardware package
« Lampholder assembly(s)
• Mounting bracket
• Shade(s)-not provided on all models
• Shade attachment screws (3 for each shade)-not provided on
all models
PREPARE THE FIXTURE
NOTE: FIRST TURN OFF ELECTRICITY
ADJUST THE CROSSBAR
1. If you are replacing an existing fixture, disconnect and remove
the old fixture. Expose the supply wiring from the outlet box.
2. Some fixtures are provided with a threaded nipple (see Fig. 1) or
machine screws (see Fig. 2 and 2A) for attaching the fixture to
the mounting bracket.If your fixture is supplied with a threaded
nipple, screw the nipple 3 complete turns into the mounting
bracket and lock into place with a hexagon lock nut. If your
fixture is supplied with machine screws, thread the machine
screws into the opposite side of the mounting bracket from the
green ground screw. Lock the machine screws into place with
locknuts. EXCEPTION: Ceiling mounted fixtures with keyhole
slots should have machine screws entering mounting bracket
from same side as green grounding screw (see Fig, 2 A)
3. Fasten the mounting bracket to the outlet box using the two
screws supplied with the outlet box.If your Fixture is supplied
with a channel shape mounting bracket with keyhole slots for
attachment to the mounting surface (see Fig.3). it will be
necessary to mark the location of the keyhole slots on the
mounting surface and drill holes for fasteners (not provided)
Use fasteners suitable for the mounting surface. The narrow
end of the keyhole slot should face up.
4. Attach grounding wire(green or bare copper) from the supply
circuit to the mounting bracket with the green grounding
attachment screw provided.Some models have a grounding wire
attached to the fixture for models that employ a green or bare
copper grounding wire, it will be necessary to connect the green
or bare grounding wire to the grounding conductor of the supply
circuit. Attach all grounding conductors to the moimting
bracket with the green grounding attachment screw.
5. Make electrical connections-SEE BELOW.
ELECTRICAL CONNECTIONS
To make electrical connections:
Connect the white wire (s) from the fixture to the white wire of the
supply circuit. Connect the black wire (s) from the fixture to the
black wire of the supply circuit. Connect me green (or bare copper)
colored wire to the grounding conductor of the supply circuit. If
your fixture is supplied with an SPT Cord connect the half of the
SPT Cord that is ribbed surface to the white wire of the supply
circuit. Connect the smooth half of the wire (the half with mark-
ings) to the black wire of the supply circuit. Use UL. Listed wire
connectors suitable for the size, type, and number of conductors.
No loose strands or loose wires should be present. Secure wire
connectors with U.L. listed electrical tape.
FINAL ASSEMBLY
1. Spread the electrical splices so that the black wires are on one
side of the outlet box and the white wires are on the other side
2. Place fixture against mounting surface allowing the threaded
nipple or machine screws to pass through the coverplate.Secure
with mounting nut or acorn nuts. For fixtures with channel
shape mounting bracket. Place the coverplate over the channel
and secure with screws provided
3. If applicable place candle cover(s) over lampholder(s) before
installing bulb (s). Install the lighfbulb(s) (not provided).
CAUTION: Refer to the relampirig label located near the
lampholder for recommended maximum wattage-do not
exceed recommended wattage.
4. If applicable,attach shades to fixture some shades require the
use of shade attachment screws . Do not overtighten these
screws-too much pressure could cause glass breakage.See Fig.
3 for placement of fabric spacer, not supplied on all models.
5. Outdoor wall fixtures must be caulked with suitable RTV or
Silicone compound around the top and sides of the coverplate to
reduce the chance of water intruding into the splicing area.
Leave the bottom clear to allow moisture a means of escape.
6. Restore electricity and check the operation of your new lighting
fixture.
Printed in China