Wireless 802.11b/g/n/a/ac USB Adapter Manufacturer: HAOLIYUAN (SHENZHEN) ELECTRONIC CO.
Chapter 1. Introduction Thank you for purchasing the wireless 802.11b/g/n/a/ac USB adapter! This adapter is mini size design and you are able to plug it into the USB port. Excepting common wireless standards 802.11b/g/n, this wireless adapter is also 802.11ac compatible data transfer rate is 300/867Mbps. Note: The antenna must not be co-located or operating in conjunction with any other antenna or transmitter 1.1 Product Features ◆ Complies with IEEE 802.11ac , IEEE 802.11a,IEEE 802.11n, IEEE 802.
wireless USB Adapter: 2.1.1 Insert the USB wireless network card into an empty USB 3.0 port of your computer when computer is switched on. Never use force to insert the card, if you feel it’s stuck, flip the card over and try again. 2.1.2 The following message will appear on your computer, click ‘Cancel / Close’. Under Windows Vista and Windows 7 2.1.3 Insert the driver CD into your CD-ROM. You can see autorun screen below. if not, you can double click ‘autorun.exe’ on CD.
reboot. you can click ‘Finish’ and reboot the computer to finish the installation of driver files. 2.1.5 A new icon will appear near the clock of system tray: Left-click the icon will launch wireless network configuration utility, and you can right-click the icon to show the quick menu of configuration utility. This icon also uses different color to show the status of wireless connection: Wireless connection is established, good signal reception. Wireless connection is established, weak signal reception.
To use wireless network, you have to connect to a wireless access point first. You can either use Client utility (comes with network card driver), or Windows Zero Config utility (comes with Windows operating system). 2.2.1 Using Client Utility Please follow the following instructions to use Client configuration utility to connect to wireless access point. 1. Left-click the Client configuration utility icon located at lower-right corner of computer desktop, and configuration menu will appear: HERE! 2.
If the wireless access point you wish to connect does not appear here, you can click ‘Refresh’ button to scan for wireless access points again; if the wireless access point you’re looking for still not appear, try to move the computer closer. When the access point you’re looking for is on the list, left-click it and then double click it or click ‘Add to Profile’. 4.
5. Network card will attempt to connect to access point now, this may require few seconds to minutes, please be patient. When the ‘Status’ become ‘Associated’ , your computer is connected to access point you selected. Click ‘Close’ to close configuration menu.
NOTE: If you connected to an access point but the connection has been dropped soon, please check security settings and re-check password spelling. 2.2.2 Using WPS Connect Wi-Fi Protected Setup (WPS) is the latest wireless network technology which makes wireless network setup become very simple. If you have WPS-enabled wireless access point, and you want to establish a secure connection to it, you don’t have to configure the wireless access point and setup data encryption by yourself.
2. 3. Click ‘Wi-Fi Protect Setup’ menu. You can use PIN code or Push-Button configuration, and WPS-compatible wireless access point must use the same type of WPS. For instructions on setup each type of WPS, see next 2 chapters for detailed instructions.
You’ll be prompted to select an access point you wish to connect. If you know its SSID, click ‘Yes’, otherwise click ‘No’. If you select ‘Yes’, a list of all WPS-compatible AP nearby will be displayed; you can click ‘Refresh’ to rescan, then select an AP and click ‘Select’ button. If you select ‘No’, wireless network card will prompt you to enter 8-digit PIN code into your AP, without selecting an AP in advance.
After you select ‘Yes’ or ‘No’ in previous step, network card will attempt to connect to WPS-compatible AP, and an 8-digit number will appear. Please input this number to AP’s configuration menu within 2 minutes, and network card will establish secure connection with AP automatically. To stop this procedure before connection is established, click ‘Cancel’. Push Button To use Push-Button WPS configuration, please click ‘Push Button Config (PBC)’ button.
Click “Push Button Config(PBC)” , a message box will appear: Please activate Push-Button function on wireless access point now, and wireless network card will establish secure connection with access point within one minute.
Utility’ 3. Remove the card and insert it into another USB port. 4. Remove the driver and re-install. 5. Contact the dealer of purchase for help. I can not establish 1. Click ‘Add to Profile’ for few more times. connection with a 2. If the SSID of access point you wish to certain wireless connect is hidden (nothing displayed in ‘SSID’ access point field in ‘Site Survey’ function), you have to input correct SSID of the access point you wish to connect.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
