802.11ac Wireless USB Adapter U1233, WU1200 User Manual Company: HAOLIYUAN (SHENZHEN) ELECTRONIC CO., LTD Name / Position: Albee shen / PM Tel:+1-626-271-1588ext.818861350 Fax:+1-626-271-1588ext.818861350 Email:Albee.j.shen@rosewill.com Address:17708 Rowland Street.
Chapter 1. Introduction Thank you for purchasing the wireless 802.11b/g/n/a/ac USB adapter! This adapter is mini size design and you are able to plug it into the USB port. Excepting common wireless standards 802.11b/g/n, this wireless adapter is also 802.11ac compatible data transfer rate is 300/867Mbps. 1.1 Product Features ◆ Complies with IEEE 802.11ac , IEEE 802.11a,IEEE 802.11n, IEEE 802.11g and IEEE 802.11b standards ◆ Provides USB2.
CHAPTER 2: Quick Installation Guide 2.1 Driver Installation Please follow the following instructions to install your new wireless USB Adapter: 2.1.1 Insert the USB wireless network card into an empty USB 2.0 port of your computer when computer is switched on. Never use force to insert the card, if you feel it‟s stuck, flip the card over and try again. 2.1.2 The following message will appear on your computer, click „Cancel / Close‟. Under Windows Vista and Windows 7 2.1.
Click „Install Driver‟ to start the installation procedure 2.1.4 Once the installation is finished the computer will be asked to reboot. you can click „Finish‟ and reboot the computer to finish the installation of driver files. 2.1.
Left-click the icon will launch wireless network configuration utility, and you can right-click the icon to show the quick menu of configuration utility. This icon also uses different color to show the status of wireless connection: Wireless connection is established, good signal reception. Wireless connection is established, weak signal reception. Connection is not established yet. Wireless network card is not detected.
3. Please wait for a while, and all wireless access points which can be reached by this wireless network card will be displayed here.
If the wireless access point you wish to connect does not appear here, you can click „Refresh‟ button to scan for wireless access points again; if the wireless access point you‟re looking for still not appear, try to move the computer closer. When the access point you‟re looking for is on the list, left-click it and then double click it or click „Add to Profile‟. 4.
5. Network card will attempt to connect to access point now, this may require few seconds to minutes, please be patient. When the „Status‟ become „Associated‟ , your computer is connected to access point you selected. Click „Close‟ to close configuration menu.
NOTE: If you connected to an access point but the connection has been dropped soon, please check security settings and re-check password spelling. 2.2.2 Using WPS Connect Wi-Fi Protected Setup (WPS) is the latest wireless network technology which makes wireless network setup become very simple. If you have WPS-enabled wireless access point, and you want to establish a secure connection to it, you don‟t have to configure the wireless access point and setup data encryption by yourself.
2. 3. Click „Wi-Fi Protect Setup‟ menu. You can use PIN code or Push-Button configuration, and WPS-compatible wireless access point must use the same type of WPS. For instructions on setup each type of WPS, see next 2 chapters for detailed instructions.
You‟ll be prompted to select an access point you wish to connect. If you know its SSID, click „Yes‟, otherwise click „No‟. If you select „Yes‟, a list of all WPS-compatible AP nearby will be displayed; you can click „Refresh‟ to rescan, then select an AP and click „Select‟ button. If you select „No‟, wireless network card will prompt you to enter 8-digit PIN code into your AP, without selecting an AP in advance.
After you select „Yes‟ or „No‟ in previous step, network card will attempt to connect to WPS-compatible AP, and an 8-digit number will appear. Please input this number to AP‟s configuration menu within 2 minutes, and network card will establish secure connection with AP automatically. To stop this procedure before connection is established, click „Cancel‟. Push Button To use Push-Button WPS configuration, please click „Push Button Config (PBC)‟ button.
Click “Push Button Config(PBC)” , a message box will appear: Please activate Push-Button function on wireless access point now, and wireless network card will establish secure connection with access point within one minute.
Utility‟ 3. Remove the card and insert it into another USB port. 4. Remove the driver and re-install. 5. Contact the dealer of purchase for help. I can not establish 1. Click „Add to Profile‟ for few more times. connection with a 2. If the SSID of access point you wish to certain wireless connect is hidden (nothing displayed in „SSID‟ access point field in „Site Survey‟ function), you have to input correct SSID of the access point you wish to connect.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
