BrightVIEW User Manual SEW-3057W.
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 3. Heed all warnings. 2. 4. 5. 6. 7. 8. 9. BrightVIEW Keep these instructions. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
SPECIFY SERVICE INSTRUCTIONS AND WARRANTY TERMS FCC Caution : Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Contents WHAT’S INCLUDED Package Contents…………………………………………………… 5 GETTING STARTED Functional Description………………………………………………… 6 Powering your monitor………………………………………………………… 6 Operating the System………………………………………………………… 6 VIEWING MODE DISPLAY Indicator Description………………………………………………… 8 How to use the indicator……………………………………………………… 8 Menu Operation…………………………………………………… 10 INSTALLATION How to Install………………………………………………………… 15 Wireless Monitor……………………………………………………………… 15 Wireless Camera………………………………………………………………
01 What’s Included What’s Included Package Contents The system comes with the following components: Wireless camera Wireless monitor User Manual & Warranty Card Camera Adapter Monitor Adapter Plastic anchor (1EA) & Screw (1EA) Wireless wrist band Wrist band Adapter Sensor Check your package to confirm that you have received the complete system, including all components shown above. English · 5 SEW-3057W.
Getting Started Operating the System Functional Description Powering your monitor After opening the box, fully charge the monitor before use. After initial charge, recharge as needed. Wireless Monitor You can use the device while charging with connected adapter, and the device is portable if charged. Wireless Camera The basic operation is as follows: Camera and Monitor pairing The units already come paired for your convenience. This button is used to add an additional camera.
Voice activated (VOX) Sound level • Low Sound Level Detection : Sets to higher sensitivity. • High Sound Level Detection : Sets to lower sensitivity. Night Light Multi camera mode Press [ / ] switch the split mode. According to the paired camera, screen split mode is different. When two cameras are paired, it displays as 2-split mode. When there are more than 2 cameras are paired, it displays as 4 split mode. Up to 4 cameras can be paired.
Viewing Mode Display e Remote View Remote access with free Apps for smartphone. f SD card status Indicator Description b c d e fghijk 12 13 14 aS ignal Indicator Unsupport SD card g x1/x1.5/x2 Zoom mode How to use the indicator a No SD card 17 16 15 Indicates that current screen is Zoomed in. Press [ zoom back out. SD card ] icon on the monitor to h Night Vision Indicator Indicates camera night vision mode is turned on. The screen will appear in Black/White in this mode.
16 Humidity Display Indicates the percent of air humidity according to the sensor. Humidity Alert range : below 45% ‐ above 65% 17 Temperature Display Indicates the temperature value according to the sensor. No Signal Warnings 03 The "Out of Range" message means the monitor cannot access the camera. Please reposition the camera, or check the camera power. Viewing Mode Display English · 9 SEW-3057W.
b -1 Photo Diary Menu Operation How to use the function tools Press the screen of the monitor to display the menu screen. a If you choose date, it will show the baby's photo. b -2 Pair / Unpair Camera The LCD suppor up to 4 cameras, you can choose the camera to pair with the monitor or unpair. b -3 Settings You can setting Vox, date & time, feed timer, phto diary setting and brightness. Detail please refer to page 11 b -4 Bluetooth you can see the bluetooth connected on or not.
Settings How to use the setup icon Press the [ e B rightness Settings Adjusts the brightness of the image shown. If you are using multiple camera, you can adjust the brightness of each individual camera.. ] icon to save the changes and return to previous menus. To return to the Live screen, press the [ ] icon. f Environment Sensor a b c d Show the temperture, humidity and air quality, once out of the limit, it will alert.
Overview Getting to know your Monitoring system Wireless Monitor After opening the box, fully charge the monitor before use. After initial charge, recharge as needed. Front Controls Monitor Antenna Receives and sends signals from or to the camera. Microphone Transmits audio to the camera when [ ] icon is pressed down and receives sound for the area near the camera. 5” LCD Screen Displays video from the camera.
Back Controls Power On/Off Turn on/off the wireless monitor. Mirco SD SD card external storage, up to 32GB supported Kick Stand Use to hold the monitor onto a table. Speaker Produces the sound transmitted from the camera(s). DC 5V Power Input 04 Connect the included AC power adapter to power and/or charge the monitor battery. (when the monitor is not placed in the optional Charge cradle). Overview Side Controls Power On/Off Turn on/off the wireless monitor.
Wireless Camera Front & Back Controls IR Sensor Night Light Button Infrared LED’s sensor you can turn the night light on or off by touch the button or remotely control. Microphone Receives sounds for the area near the camera, and transmits sound from the camera to the monitor. Camera Antenna Sends & receives signals to or from the monitor. Sensor Temperature and humidity sensor and dust sensor. DC 5V Power Input Connect the adapter to the camera.
Wireless wrist band The button of the Wireless wrist band function: 1) press the button when the wireless wrist band black srceen, it will shin last for 6 seconds. 2) When wireless wrist band shake, by pressing the button can stop it shake. Button Show AM or PM. Show the time. Wireless Camera Before you install the camera, carefully plan where and how it will be positioned, and where you will route the cable that connects the camera to the power adapter.
Remote View 1. Go to App store to download and install "Baby View" into your Mobile phone and install .(picture1) 2. Power the camera. 3. Press the "reset" button on the camera. 4. Press "setting button" of your cell-phone to search the camera Wi-Fi, touch the camera Wi-Fi to connect. (picture2,3) 5. Click the APP, then click "tap here to add device" (picture4). 6. Scan the QR code of the bottom camera, default password "000000",click “OK” (picture5,6).
picture13 05 Installation English · 17 SEW-3057W.
Appendix Lens Specifications Image Sensor Type Effective Pixel Resolution Image Compression Max.Framerate Streaming Capability IP Protocol Streaming Method Max. User Access White Balance Item Viewing Angle (Diagonal) Wireless Camera 1/4” Color CMOS Image Sensor H: 1280, V: 1024 High : 2.5 Mbps(1280x720@~15fps), Middle : 1.
Item Feed Timer Alert sensor temperature alert range (User range) Yes (beep sound) Details Display Item Details Digital watch / Battery check / connection check Control part push toggle Transmission range 10 meters Air quality : above 200 Weight / Strip length 9g/150 - 220mm (adjustable range for length) Number of Camera Support Up to 4 cameras Temperature sensor Yes (+/-2 degree), Power Requirement Adapter : DC 5V ± 10%, Battery : 3.
Problem Your BrightVIEW is emitting an high pitched noise/ feedback. Solution This sound is normal feedback which occurs if the monitor and camera are too close together. Move them further apart. batteries will cause the supply current to become unstable and will affect the quality nn `` Low of the video/audio. Please charge the battery fully for use for superior video.
Screw holes for the Camera installation ON PAIR RESET This template is used to install the camera on the wall. OFF TEMPLATE CAMERA FRONT SEW-3057W.
MEMO SEW-3057W.
Head Office 86 Cheonggyecheon-ro Jung-gu Seoul 04541 Korea Tel +82.2.729.5277, 5254 Fax +82.2.729.5489 www.hanwha-security.com Hanwha Techwin America 500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666 Toll Free +1.877.213.1222 Direct +1.201.325.6920 Fax +1.201.373.0124 Hanwha Techwin Europe Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom Tel +44.1932.57.8100 Fax +44.1932.57.8101 SEW-3057W.