DOWN/ LEFT/ RIGHT/ MENU/ OK button DOWN/ LEFT/ RIGHT/ MENU/ OK buttons activate the following. - DOWN button : While the menu is showing, press the DOWN button to move from the main menu to a sub menu, or to move down the sub menu cursor. - LEFT button : While the menu is showing, press the LEFT button to select the menu tab to the left of the cursor. - RIGHT button : While the menu is showing, press the RIGHT button to select the menu tab to the right of the cursor, or to move an secondary menu.
Delete ( ) button This deletes images stored on the memory card. Deleting Images in Play Mode 1. Select an image that you want to delete by pressing the LEFT / RIGHT button and press the DELETE ( ) button. 2. A message will display as shown alongside on the LCD monitor. 3. Press the OK button to delete the image. DELETE ? DEL:OK CANCEL: Deleting Images in Thumbnail Display Mode 1. Use the Up/Down/Left/Right buttons to select an image to delete. 2.
Setting up the play back function using the LCD monitor PLAY mode functions can be changed by using the LCD monitor. In the PLAY mode, pressing the MENU button displays the menu on the LCD monitor. The menus you can set up in Play mode are as follows. To capture an image after setting up the play menu, press the PLAY button. The items indicated by Menu tab Main menu SLIDE are default settings.
Setting up the play back function using the LCD monitor This menu is available while the camera is connected to a PictBridge supporting printer (direct connection to the camera, sold separately) with a USB cable. Menu tab Main menu IMAGES Sub menu Secondary menu ONE PIC - ALL PICS - YES - NO - Page p. 74 AUTO SET p. 75 AUTO POSTCARD 4X6 SIZE 8X10 A6 A4 B5 AUTO FULL CUSTOM SET p. 75 1 LAYOUT 2 4 6 8 AUTO PLAIN TYPE PHOTO FASTPHO.
Setting up the play back function using the LCD monitor Menu tab Main menu Sub menu Secondary menu Page AUTO DRAFT QUALITY NORMAL FINE AUTO p. 75 CUSTOM SET DATE OFF ON AUTO FILE NAME OFF ON STANDARD - INDEX - YES - NO - YES - NO - PRINT p. 76 p. 76 DPOF PRINT p. 77 RESET Menus are subject to change without prior notice.
Starting the slide show Images can be displayed continuously at pre-set intervals. You can view the slide show by connecting the camera to an external monitor. Configure the interval for the slide show : Configure the length of time to display each picture in the slide show. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [SLIDE] menu tab. SLIDE 3.
Starting the slide show Configure slide show effects: Unique screen effects can be used for the slide show. Steps 1 and 2 are the same as for the [INTERVAL] section. 3. Select the [EFFECT] sub menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Use the Up/Down Button to select the type of effect. SLIDE [CANCEL] : Normal display. CANCEL INTERVAL [EFFECT 1] : Image is displayed slowly. EFFECT1 REPEAT EFFECT2 EFFECT [EFFECT 2] : Image is displayed slowly from the SET:OK BACK: center outwards.
Protecting images - If you protect an image, the protect icon will be displayed on the LCD monitor. (An unprotected image has no indicator) - An image in LOCK mode will be protected from the delete function or [DELETE] functions, but will NOT be protected from the [FORMAT] function. Deleting images Of all the files stored in the memory card, the unprotected files in the DCIM subfolder will be deleted. Remember that this will permanently delete unprotected images.
Resize Change the resolution (size) of pictures taken. Select [LOGO] to save an image to be the start-up image. The resized image will have a new file name. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [RESIZE] menu tab. RESIZE 3. Select a desired sub menu by pressing the UP/ DOWN 1600X1200 1280X960 button and press the OK button.
Rotating an image You can rotate the stored images by 90, 180, or 270 degrees. You can view a picture in its proper orientation if the picture has been taken with the camera oriented vertically or up-side-down. Once the playback of the rotated picture is finished, it will switch back to the original state. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [ROTATE] menu tab. 3. Select a desired sub menu by pressing the UP/ DOWN button.
DPOF : STANDARD This function allows you to embed print quantity information on a stored image. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [DPOF] menu tab. 3. Select the [STANDARD] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. [SELECT]: Selection window for an image to print is displayed. - Up/Down/Left/Right: Select an image to print.
DPOF : PRINT SIZE You can specify the print size when printing images stored on the memory card. The [SIZE] menu is available only for DPOF 1.1 compatible printers. Setting the Print Size 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [DPOF] menu tab. 3. Select the [SIZE] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button.
PictBridge You can use the USB cable to connect this camera to a printer that supports PictBridge (sold separately) and print the stored images directly. TIFF, Movie clips and voice files cannot be printed. You can set up the following settings from the PictBridge menu. IMAGES : Select the pictures to be printed.
PictBridge: Picture Selection Select pictures to print 1. Connect the camera to your printer. The USB menu must be set to [PRINTER] before you connect the camera to the printer.(See p.86) IMAGES 2. The [IMAGES] menu will appear. ONE PIC 3. Use the UP and DOWN buttons to select the desired ALL PICS submenu value, and then press the OK button. MOVE: SET:OK When [ONE PIC] is selected : The PictBridge function will be applied only to the picture currently displayed.
PictBridge: Print Setting AUTO SET 1. Connect the camera to your printer. The USB menu must be set to [PRINTER] before you connect the camera to the printer.(See p.86) 2. Use the LEFT and RIGHT buttons to select the [AUTO SET] menu tab. 3. Use the UP and DOWN buttons to select the desired submenu value, and then press the OK button. [YES]: All values in the [CUSTOM SET] are automatically changed. [NO] : [CUSTOM SET] values are kept.
PictBridge: Printing Printing Pictures 1. Connect the camera to your printer. The USB menu must be set to [PRINTER] before you connect the camera to the printer.(See p.86) PRINT 2. Use the LEFT and RIGHT buttons to select the [PRINT] STANDARD menu tab. INDEX 3. Use the UP and DOWN buttons to select the desired MOVE: SET:OK submenu value, and then press the OK button. [STANDARD] : Print the pictures stored in the memory card in set numbers. One picture is printed on one piece of paper.
PictBridge : RESET Initializes user-changed configurations. 1. Connect the camera to your printer. The [USB] menu must be set to [PRINTER] before you connect the camera to the printer.(See p.86) 2. Use the LEFT and RIGHT buttons to select the [RESET] menu tab. 3. Use the UP and DOWN buttons to select the desired submenu value, and then press the OK button. - If [YES] is selected : All print and image settings will be reset. - If [NO] is selected : Settings will not be reset.
Setup menu In this mode, you can set up basic settings. You can use the setup menu in all camera modes, except Voice Recording mode. The items indicated by are default settings. Menu tab Main menu Sub menu Secondary menu Page RESET FILE p.79 SERIES PWR OFF OFF, 1~3~10MIN p.80 ENGLISH P”CCK»… FRANÇAIS PORTU. DEUTSCH DUTCH ESPAÑOL DANSK ITALIANO SVENSKA LANGUAGE p.81 SUOMI THAI NO p.81 FORMAT YES 04/07/01 13:00 YY/MM/DD D & TIME p.82 DD/MM/YY MM/DD/YY OFF IMPRINT DATE p.
Setup menu Menu tab Main menu Sub menu Secondary menu Page DARK LCD NORMAL p.83 BRIGHT NTSC p.84 VIDEO PAL Q. VIEW OFF, 1, 2, 3SEC p.85 NO RESET p.85 YES COMPUTER USB p.86 PRINTER * Menus are subject to change without prior notice. File name This function allows the user to select the file naming format. Assigning File Names 1. In any mode with the exception of Voice Recording mode, press the MENU button. NOR 2816 2. Press the LEFT/ RIGHT button and select the [SETUP] SETUP menu tab.
File name INFORMATION The first stored folder name is 100SSCAM, and the first file name is SV600001. File names are assigned sequentially from SV600001 SV600002 ~ SV609999. The folder number is assigned sequentially from 100 to 999 as follows: 100SSCAM 101SSCAM ~ 999SSCAM. The files used with the memory card conform to the DCF(Design rule for Camera File systems) format. Auto power off This function switches the camera off after a set amount of time in order to prevent unnecessary battery drainage.
Language There is a choice of languages that can be displayed on the LCD monitor. Even if the batteries or AC adapter are removed and inserted again, the language setting will be preserved. Setting Language 1. In any mode with the exception of Voice Recording mode, press the MENU button. NOR 2816 2. Press the LEFT/ RIGHT button and select the [SETUP] SETUP menu tab. ENGLISH FILE 3. Select the [LANGUAGE] menu by pressing the UP/ PWR OFF DOWN button and press the RIGHT button.
Setting up the Date/ Time/ Date type You can change the date and time that will be displayed on the captured images and set up the date type. Setting Date/Time & Selecting Date Format 1. In any mode with the exception of Voice Recording mode, press the MENU button. NOR 2816 2. Press the LEFT/ RIGHT button and select the [SETUP] SETUP menu tab. LANGUAGE FORMAT 3. Select the [D&TIME] menu by pressing the UP/ DOWN YY/MM/DD D & TIME button and press the RIGHT button. SET:OK BACK: 4.
Sound If you set the operation sound to ON, various sounds will be activated for camera startup, when button are pressed, and if there is a card error, so that you can be aware of the camera operation status. Setting Operation Sounds 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [SETUP] menu tab. 3. Select the [SOUND] menu by pressing the UP/ DOWN button and press the RIGHT button. 4.
Selecting Video out type The Movie output signal from the camera can be NTSC or PAL. Your choice of output will be governed by the type of device (monitor or TV, etc.) to which the camera is connected. PAL mode can support only BDGHI. Setting the Video Out Type 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [SETUP] menu tab. 3. Select the [VIDEO] menu by pressing the UP/ DOWN button and press the RIGHT button. 4.
Quick view If you enable Quick View before capturing an image, you can view the image you just captured on the LCD monitor for the duration set in the [Q.VIEW] setup. Quick view is possible only with still images. Setting Quick View 1. In any mode with the exception of Voice Recording mode, press the MENU button. NOR 2816 2. Press the LEFT/ RIGHT button and select the [SETUP] SETUP menu tab. LCD 1 SEC VIDEO 3. Select the [Q.VIEW] menu by pressing the UP/ DOWN Q. VIEW button and press the RIGHT button.
Connecting an External Device (USB) You can select an external device to which you want to connect the camera using the USB cable. Selecting an External Device 1. In any mode with the exception of Voice Recording mode, press the MENU button. NOR 2816 2. Press the LEFT/ RIGHT button and select the [SETUP] SETUP Q. VIEW menu tab. COMPUTER RESET 3. Select the [USB] menu by pressing the UP/ DOWN button PRINTER USB and press the RIGHT button. SET:OK BACK: 4.
Setting up the MYCAM menu You can set up a start up image, start up sound and shutter sound. Every camera working mode (with the exception of Voice recording mode) has the MyCAM menu. The items indicated by are default settings. Menu tab Main menu Sub menu OFF USER IMAGE Page IMAGE 1 S.IMAGE p.87 IMAGE 2 IMAGE 3 OFF SOUND 1 SOUND 2 SOUND 3 OFF SOUND 1 SOUND 2 SOUND 3 p.88 S.SOUND p.88 SH.SOUND * Menus are subject to change without prior notice.
Start up sound You can select the sound that is activated whenever the camera is turned on. Setting the Startup Sound 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [MYCAM] menu tab. 3. Select the [S.SOUND] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. 5. Press the menu button twice and the menu will disappear.
Important notes Be sure to observe the following precautions! This unit contains precision electronic components. Do not use or store this unit in the following locations. - Areas exposed to severe changes in temperature and humidity. - Areas exposed to dust and dirt. - Areas exposed to direct sunlight or the inside of a vehicle in hot weather. - Environments where there is high magnetism or excessive vibration. - Areas with high explosives or highly flammable materials.
Important notes If the camera is exposed to an electronic interference, it will turn itself off to protect the memory card. Camera Maintenance - Use a soft brush (available from photo stores) to gently clean the lens and LCD assemblies. If this does not work, lens-cleaning paper with lens cleaning fluid can be used. Clean the camera body with a soft cloth. Do not allow this camera to come into contact with solvent materials such as benzol, insecticide, thinners etc.
Warning indicator There are several warnings that may appear on the LCD display Warning indicator Causes - Memory card error CARD ERROR ! Remedy - Turn off the camera power and turn it on again - Insert the memory card again - Format the memory card (p.
Before contacting a service center Please check the following Symptom The camera doesn t switch on Causes Remedy - There is low battery capacity - Insert fresh batteries - An AC Power Adapter is not - Connect an AC Power Adapter connected - Batteries are inserted incorrectly with the reverse - Insert the batteries according to the polarity marks (+, -) polarities The camera power ceases whilst in use - The batteries are exhausted - Insert fresh batteries - The Camera is turned off - Press the
Before contacting a service center Symptom Causes - A picture was taken within 0.8 m from the subject without The images are unclear Remedy - If the subject is closer than 0.
Before contacting a service center Symptom Colour of image is different to the original scene Images are too bright No image on external monitor Causes - White balance setting is Remedy - Select appropriate White balance incorrect - Exposure is excessive - Reset exposure compensation - The external monitor has not - Check the connection cables been connected properly with the camera - There are incorrect files in the - Insert a memory card that has correct files memory card - Cable connection i
Specifications Type Effective Pixel Total Pixel Image Sensor Focal Length Lens F No. Digital Zoom Optical Viewfinder LCD Monitor Type Viewfinder Focusing Range Type Speed Shutter Control Exposure Compensation ISO Equivalent Modes Range Recharging Time Flash Sharpness Effect White Balance Voice Recording Date Imprinting Still Image Shooting Movie Clip Media Storage File Format 1/1.8" CCD Approx. 6.1 Mega-pixel Approx. 6.3 Mega-pixel Schneider Lens f = 7.7 ~ 23.
Specifications Image Size Storage Capacity (32MB) Image Play Type Editing Interface Power Source Dimensions (WxHxD) Weight Operating Temperature Operating Humidity Camera Software DriverApplication Special Features 2816 : 2816x2112 2560 : 2560x1920 2272 : 2272x1704 2048 : 2048x1536 1600 : 1600x1200 1024 : 1024x768 640 : 640x480 2816 : Super Fine 9, Fine 18, Normal 26, TIFF 1 2560 : Super Fine 11, Fine 22, Normal 32, TIFF 2 2272 : Super Fine 14, Fine 28, Normal 40, TIFF 2 2048 : Super Fine 17, Fine 3
Software Notes Please ensure that you read the instruction manual carefully before use. The attached software is a camera driver and image editing software tool for Windows. Under no circumstances should all or part of either the software or the user manual be reproduced. Copyrights for software are licensed only for use with a camera. In the unlikely event of a manufacturing fault, we will repair or exchange your camera.
About the software After inserting the CD-ROM provided with this camera into the CD-ROM drive, the following window should automatically run. Before connecting the camera to the PC, you should first install the camera driver. Figures (Images) used for the manual are based on model Digimax V5. Camera driver : This enables images to transfer between the camera and PC. This camera uses the USB Storage Driver as the camera driver. You can use the camera as a USB card reader.
Setting up the application software To use this camera with a PC, install the application software first. After this has been done, the stored images in the camera can be moved to the PC and can be edited by an image editing program. INFORMATION Close other programs before installing the application software. Before installing the application software, disconnect the USB connection. You can visit the Samsung web-site through the internet. http://www.samsungcamera.com : English http://www.samsungcamera.co.
Setting up the application software 3. A window for which you can select application software will be displayed. Select the application program and click the [Install] button. Refer to page 98 for more information about the application program. [Click!] INFORMATION If you select [Exit] at the step 3, the application program installation will be cancelled. 4. Install Digimax Viewer. Click [Next >] button.
Setting up the application software 7. A window will open, asking you to choose a folder to which program icons will be added. Click [Next >] button. If you want to add the program icons to a different folder, choose another folder, and then click [Next >] button. [Click!] 8. Digimax Viewer installation is successfully completed. Click the [Finish] button to install PhotoImpression.The system will not reboot even the [Yes, I want to restart the computer now] option is selected.
Setting up the application software 12. A destination selection window will open. Click [Next >]. To copy to the files to another folder, click [Browse...] and choose a folder you want. [Click!] 13. The [Select Components] window will appear. Click [Next >] button. [Click!] 14. A window will open, asking you to choose a folder to which program icons will be added. Click [Next >] button. If you want to add the program icons to a different folder, choose another folder, and then click [Next >] button.
Setting up the application software 15. Installation is complete. To apply changes, you must restart the computer. Select [Yes, I want to restart my computer now], and then click [Finish]. [Click!] 16. After restarting the computer, connect the PC to the camera with the USB cable. 17. Turn the camera power on. [Found New Hardware Wizard] will open and the computer will recognize the camera. If you have ever installed an image viewer program or your OS is Windows XP, an image viewer program will open.
Setting up the application software INFORMATION If you have installed the camera driver, [Found New Hardware Wizard] may not open. On a Windows 98 or 98 SE system, the Found New Hardware Wizard dialog box opens and a window asking you to select a driver file may appear. In this case, specify "USB Driver" in the CD supplied. (for Windows 98 and 98 SE). When connecting the camera to your PC, it is recommended that you use an AC power adapter.
Starting PC Mode If you connect the USB cable to a USB port on your PC and then turn on the power, the camera will automatically switch to "computer connection mode". In this mode, you can download stored images to your PC through the USB cable. The LCD monitor is always turned off in PC mode. The auto focus lamp will illuminate when the files are transferring via the USB connection. Connecting the camera to a PC 1. Turn the PC power on. 2. Turn the camera power on. 3.
Starting PC Mode Downloading stored images You can download the still images stored on the camera to your PC's hard disk and print them or use a photo editing software to edit them. 1. Connect the camera to your PC with the USB cable. 2. On your computer's desktop display, select [My computer] and double click [Removable Disk DCIM 100SSCAM]. The image files will then be displayed. 3. Select an image and press the right mouse button. 4. A pop-up menu will open. Click [Cut] or [Copy] menu.
Starting PC Mode 6. Press the right mouse button and a pop-up menu will open. Click [Paste]. 7. An image file is transferred from the camera to your PC. - By using [Digimax Viewer], you can see the stored images in the memory directly on the PC monitor and you can copy or move the image files.
Removing the USB Driver for Windows 98SE To remove the USB driver, refer to the process shown below. 1. Trace [Start Settings] and click [Control Panel]. 2. Double-click [Add/Remove programs]. 3. The [Add/Remove Programs Properties] window will open. Click [Digimax V6 V6000] and click the [Add/Remove] button. [Click !] 4. Uninstallation is complete. Click the [Finish] button and the window will disappear.
Removable Disk To use this camera as a Removable Disk, install (p.99) the USB Driver. 1. Before turning the camera power on, connect the camera to the PC with the USB cable. 2. Click [Removable Disk] under [My computer] or [Windows Explorer]. 3. Image files stored in the Removable Disk (DCIM PC. 100SSCAM) can be transferred to the INFORMATION Important information whilst using the Removable Disk The [Removable Disk] indicator will not show when the camera power is off or the USB cable is removed.
Removing the removable disk Windows 98SE 1. Check whether the camera and PC are transferring a file. If the auto focus lamp blinks, you have to wait until the lamp illuminates. 2. Unplug the USB cable. Windows 2000/ME/XP (The illustrations may be different from the real display in accordance with the Windows O/S.) 1. Check whether the camera and PC are transferring a file. If the auto focus lamp blinks, you have to wait until the lamp illuminates. 2.
Removing the removable disk 6. A [Unplug or Eject Hardware] window will open. Click the [Close] button and the removable disk will be removed safely. 7. Unplug the USB cable. [Click!] Setting up the USB Driver for MAC 1. A USB Driver for MAC is not included with the software CD as MAC OS supports the camera driver. 2. Check the MAC OS. You can check the MAC OS version during MAC OS start-up. This camera is compatible with MAC OS 9.0 ~ 10.2. 3.
Using PhotoImpression With PhotoImpression, you can edit or store still images that you downloaded from the camera. This software is only available in Windows version. Programs To start the program, click [Start PhotoImpression4]. The following screen will appear. ArcSoft PhotoImpression 4 [ Help Button ] [ Command Button ] [ Tool Bar ] You can use PhotoImpression to perform the following tasks.
Using PhotoImpression Tool Bar Button Description Button Description Resize Layer Rotate Layer Flip Layer Horizontally Rotate All Layers Undo Redo Copy Paste Delete Layer Close Picture INFORMATION For detailed instruction on how to use PhotoImpression, please refer to the program's Help. Digimax Viewer 2.1 This software is only compatible with Windows. 1. To open Digimax Viewer, click the [Start Programs Samsung Digimax Viewer 2.1 Digimax Viewer 2.1 ] and Digimax Viewer 2.1 will then open.
Digimax Viewer 2.1 3. You can easily use the Digimax viewer 2.1 program as it offers a FILE menu and TOOL bar. And, you can use the pop up menu. Click an image and press the right mouse button. Digimax Viewer functions are listed below. - Basic functions : Copy, Cut, Paste, Delete, Rotate, Rename, changing file type, Resize, Property. - Advanced functions : Print, Slide show, Export, Sending e-mail, On-line print, Web album etc.
FAQ [Case 4] The camera is not recognized by your PC. Sometimes, the camera may appear under [Unknown Devices] in Device Manager. Install the camera driver correctly. Turn off the camera, remove the USB cable, plug in the USB cable again, and then turn on the camera. [Case 5] There is an unexpected error during file transfer Turn the camera power off and on again. Transfer the file again. [Case 6] How do I know my computer supports a USB Interface? Check the USB port in your computer or keyboard.
FAQ [Case 9] When I open the Device Manager (by clicking Start (Settings) Control Panel (Performance and Maintenance) System (Hardware) Device Manager), there are Unknown Devices or Other Devices entries with a yellow question mark(?) beside them or devices with an exclamation mark(!) beside them. Right-click on the entry with the question(?) or exclamation (!) mark and select "Remove". Restart the PC and connect the camera the again.
FAQ 1) When the movie clip plays back, only the sound plays back without the image. It isn't compatible with the Mogen MJPEG Decoder. Uninstall the Mogen MJPEG Decoder as following order. Click [Start Run] and a window will open. Type "regsvr32 /u m3jpgdec.ax" and press the Enter key. 2) When the movie clip plays back, the blue and red colors are reversed or the movie clip doesn't open. It isn't compatible with the ffdshow Codec or K-lite Codec Pack. Disable the ffdshow program.
Information to the user NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
MEMO 119
SAMSUNG TECHWIN CO., LTD. OPTICS & DIGITAL IMAGING DIVISION 145-3, SANGDAEWON 1-DONG, JUNGWONGU,SUNGNAM-CITY, KYUNGKI-DO, KOREA 462-121 TEL : (82) 31-740-8086,8088, 8090, 8092, 8099 FAX : (82) 31-740-8398, 8111 SAMSUNG OPTO-ELECTRONICS AMERICA, INC. HEADQUARTERS 40 SEAVIEW DRIVE, SECAUCUS, NJ07094, U.S.A. TEL : (1) 201-902-0347 FAX : (1) 201-902-9342 WESTERN REGIONAL OFFICE 18600 BROADWICK ST., RANCHO DOMINGUEZ, CA 90220, U.S.A.