CDMA WLL User’s Guide HTT-800A CDMA – 2000 1X Fixed Wireless Terminal User's Guide Model No. HTT-800A Supports Voice, PCO, G3 Fax, Data Read this manual carefully before operating the instrument. V1.
CDMA WLL User’s Guide HTT-800A FCC RF EXPOSURE INFORMATION WARNING! Read this information before using your phone In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96~326 adopted an updated safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies.
CDMA WLL User’s Guide Warning: HTT-800A Exposure to Radio Frequency Radiation The radiated output power of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact during normal operation is minimized. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna should not be less than 20 cm during normal operation.
CDMA WLL User’s Guide HTT-800A CONTENTS FCC RF EXPOSURE INFORMATION..................................... 2 HIGHLIGHTS ........................................................................... 9 1. BEFORE YOU START ................................................... 13 1.1 SAFETY PRECAUTIONS........................................ 13 1.1.1 Warning............................................................ 13 1.1.2 Important.......................................................... 13 1.
CDMA WLL User’s Guide HTT-800A 2.9 Multi-extension Installations ................................. 26 3. BASIC FUNCTIONS .......................................................... 27 3.1 Power On/Off .......................................................... 27 3.2 Making a call........................................................... 28 3.3 Receiving a call....................................................... 28 3.4 Ending a call ........................................................... 29 4.
CDMA WLL User’s Guide HTT-800A 4.11 R-UIM (Optional) .................................................. 38 4.12 Authentication Function (Optional) ...................... 39 5. SUPPLEMENTARY FUNCTIONS ..................................... 40 5.1 Call Functions ......................................................... 40 5.1.1 Speed Dial ........................................................ 40 5.1.2 Redialing .......................................................... 41 5.1.3 Emergency call .............
CDMA WLL User’s Guide HTT-800A 6. SYSTEM FUNCTIONS ...................................................... 52 6.1 Call Waiting............................................................. 52 6.2 Three-way calling.................................................. 52 6.3 Call Forwarding ...................................................... 52 7. FAX FUNCTIONS .............................................................. 53 7.1 FAX Set-up............................................................. 53 7.
CDMA WLL User’s Guide HTT-800A 9.1 Advanced Functions ............................................... 96 9.2 Supplementary Functions ....................................... 98 10. TROUBLESHOOTING GUIDE .................................... 1021 11. SPECIFICATIONS .......................................................
CDMA WLL User’s Guide HTT-800A Highlights Dear Customer, Congratulations on your purchase of the Fixed Wireless Terminal Model No. HTT-800A designed to operate on the latest digital mobile communications technology, Code Division Multiple Access (CDMA). This CDMA digital technology has greatly enhanced voice clarity and can provide various advanced features. The terminal enables the normal operation and direct connection of standard telephone equipment into the cellular network.
CDMA WLL User’s Guide HTT-800A ■ This Model offers its users superior voice quality through its use of QCELP or EVRC Vocoder. ■ Various sounds and LED functions provide audio and visual alerts for Low Battery, Air Link Cut-Off and Function status. ■ The owner can use the terminal with the Outgoing Call Lock function. ■ Connect this Model with your PC for data transmission, PC Fax and SMS communication.
CDMA WLL User’s Guide HTT-800A This Model provides: ■ AC Power supply with AC/DC Adapter. ■ Touch tone (DTMF) or Pulse Dialing ■ A phone jack to plug in the telephone equipment (RJ-11 Port) ■ Support Caller ID Telephone ■ Ring voltage used to ring the telephone connected to the unit, with a REN (Ringer Equivalence Numbers) of 4 Phones.
CDMA WLL User’s Guide HTT-800A For instance, the following features may not be supported: ■ Emergency Call ■ Hot Line Call ■ Speed Dial ■ Alarm ■ Outgoing Call Lock -12-
CDMA WLL User’s Guide HTT-800A 1. Before You Start 1.1 SAFETY PRECAUTIONS 1.1.1 Warning To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. Do not use this product near swimming pools or other bodies of water. Telephones with multiple terminating impedance, should be set for 600ohms. The adapter provided along with FWT is designed for a rated voltage only. So it may cause trouble, if the adapter is used out of a rated voltage range. 1.1.
CDMA WLL User’s Guide HTT-800A phone. ■ For the best call quality, keep the antenna free from obstructions and point the antenna straight up. ■ Do not operate your product when holding the antenna, or when someone is within four inches (ten centimeters) of the antenna. Holding the antenna affects call quality and may cause the telephone to operate at a higher power level than needed.
CDMA WLL User’s Guide HTT-800A to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the radio or television and the telephone. - Connect the equipment into an outlet on a circuit different from that to which the terminal is connected. - Consult you Authorized Dealer of an experienced Radio/TV technician for help. ■ Use only the battery, antenna and AC power supply provided by Authorized Dealer.
CDMA WLL User’s Guide HTT-800A ■ Avoid shock or impact. ■ We recommend you to charge the backup battery before initial use for 10/12 hours. Backup battery may be discharged during delivery. ■ This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: - This device may not cause harmful interference, and - This device must accept any interference received, including interference that may cause undesired operation. 1.
CDMA WLL User’s Guide HTT-800A - The unit has been exposed to rain or water. - Liquid has been spilled into the unit. - The power supply cord is damaged or frayed. - The unit has been dropped or damaged. - The unit does not work normally by following the operating instructions. Note: ■ Don't disassemble or modify this product deliberately. ■ Use only an approved adapter. ■ Don't touch adapter with wet hands. ■ Don't install this product in dusty area.
CDMA WLL User’s Guide HTT-800A Green ) 2. Getting Started and Installation 2.1 Checking the Parts Please make sure that these components are present before you begin the unit installation. And then compare the following figures and components. If components are missing or damage is found, contact the store where you purchased the unit immediately.
CDMA WLL User’s Guide HTT-800A 2.2 Know your Terminal 1. Antenna: Connector Connecting Port for TNC Antenna 2. LEDs: Indicate the status of the unit - LED indications are described in the following table.
CDMA WLL User’s Guide Name LED HTT-800A Activity Meaning Color AC/DC adapter is giving 12V DC GREEN On ORANGE On ORANGE Flashing RED On RED Flashing - Off GREEN On without a battery. Battery is fully charged. (AC/DC adapter is connected.) POWER SIGNAL MODE Battery is charging. (AC/DC adapter is connected.) Battery Power is applied without AC/DC adapter. Low Battery Warning. (AC/DC adapter is not connected.) No AC Power/No power is being supplied by battery.
CDMA WLL User’s Guide HTT-800A 6. PHONE / FAX (RJ-11 port): Connecting Ports for a G3 FAX Machine or SLT (Single Line Telephone) 7. DC 12V: 12V AC/DC Power Adapter. The SMPS supplies the power to the FWT terminal. 2.3 Setting up your Terminal This Model operates by receiving electricity from an AC/DC Adapter or internal battery. 1. Connect Indoor antenna on the Rear side of the terminal. 2. Connect a conventional wired telephone to a RJ-11 PHONE compatible to port.
CDMA WLL User’s Guide 4. Plug the HTT-800A AC/DC adapter plug into an appropriate electrical outlet. 5. Connect a G3 analog facsimile machine to a dedicated RJ-11 port marked as FAX. 2.3.1 Adjust Your FWT 1. Pick up the phone receiver and listen to dial tone. 2. If you hear dial tone, make a call. 3. If ether static or echo is heard While you’re talking with the other party move the antenna until you find the spot where voice conversation is strong, and static and echo are minimized.
CDMA WLL User’s Guide HTT-800A 2.3.3 Additional Telephone Equipment If you plan to use a device other than a telephone with your FWT, make sure that device will work with a normal wired telephone line. Fax Machines – Connect a fax machine with the same way it needs to be set up for use on a regular wired telephone line. 2.4 Installation on Desktop Installing your FWT Terminal on a desktop is very easy. Simply place the FWT Terminal on the desktop (or any flat, desk, table, stable horizontal surface, etc.
CDMA WLL User’s Guide HTT-800A them in all the way. Leave space between the screw head and the installation sheet. ■ Install the FWT on 02 screws with the help of eyeholes provided on the rear side of unit. 2.6 How to Install Battery 1. Open battery cover on the bottom side of the FWT. 2. Connect the battery on battery socket of the FWT. 3. Insert the battery pack in the right position between the hold bars. 4. Close the battery cover.
CDMA WLL User’s Guide HTT-800A Note: You need to be careful for getting hurt when you change the battery pack. 2.7 Installation for the Data Service As shown below, connect a USB or RS-232 data cable to the port mark as Data port on side of the FWT. 2.8 Indications Sound indications are described in the following table: Type Status Meaning The FWT is in-service with Normal 20 sec on ; 300 adequate receive signal.
CDMA WLL User’s Guide HTT-800A 2.9 Multi-extension Installations This Model has 2 jacks. You can connect up to 4 phones to the terminal using RJ-11 jack. A user must buy additional parts to extend the connection. For a multi-extension installation, make sure that all the extensions are on-hook. If one extension is off-hook (not hang up), none of the extensions on that line will ring when a call is being received.
CDMA WLL User’s Guide HTT-800A 3. Basic Functions 3.1 Power On/Off ¾ The power jack is on the side of the FWT. The POWER LED indicates the present status; ¾ When the terminal is succeeded in getting the service, SIGNAL LED indicates the strength of the signal. Lifting handset on telephone, dial tone is heard and you can enter a phone number. Note: - When you turn on the FWT, it will automatically search for service signal.
CDMA WLL User’s Guide HTT-800A 3.2 Making a call 1. First check to see that your FWT Phone is turned on. 2. Pick up the handset. You will hear a dial tone. 3. Using the number keypad, dial the desired telephone number (Max 32 digits). Note: When you finish entering phone number, the call will be connected automatically after 5 seconds. Please Refer to 4.9 Auto dial time. 4. When the other person answers, begin your conversation. 5. To end the call, replace the handset.
CDMA WLL User’s Guide HTT-800A Note: When the handset is picked up and the incoming call is ringing, you can receive the call by pressing any key. 3.4 Ending a call When you have completed the call, place the handset back on telephone. Also you can hook flash more than about 1 second to end a call and place a new call without hanging up the handset.
CDMA WLL User’s Guide HTT-800A 4. Advanced Functions & Setting 4.1 One Minute Alert A one minute alert is generated after each minute interval into the call conversation to notify you that a minute has passed since the beginning of the call or after the previous time of discrete tone, regardless of when you make or receive a call. 1. Pick up the handset. 2. Press <*>, <*> and <0>, <1>. 3. Press <*> to set 1 minute alert. Press <#> to release 1 minute alert. 4.
CDMA WLL User’s Guide 4.2.2 24 HTT-800A Hour Mode 1. Pick up the handset. 2. Press <*>, <*>, <0>, <2> and <2 (24 Hour mode)>. 3. Press alarm time (00:00~23:59). 4. Press <*> to set alarm. 4.2.3 Release Alarm Setting 1. Pick up the handset. 2. Press <*>, <*>, <0>, <2> and <#>. Note: When you will hear the alarm sound, pick up the handset to turn off alarm. 4.3 Connection tone A connection tone is generated when a call is connected successfully. 1. Pick up the handset. 2. Press <*>, <*> and <0>, <3>.
CDMA WLL User’s Guide HTT-800A 4.4 Earpiece Volume You can adjust the Earpiece volume to levels 1-4. The Number 4 is highest volume. 1. Pick up the handset (Standby mode). 2. Press <*>, <*> and <0>, <4>. 3. Press to select one among from <1> to <4>. 4. Press <*> for save. 4.5 CID / CLIP Mode If your phone connected to the FWT is caller ID enabled, you can set the FWT to display the caller number on the phone. The default setting of caller ID is DTMF type. 1. Pick up the handset. 2.
CDMA WLL User’s Guide HTT-800A activate or deactivate Caller ID. 4.6 Calls Restrict 4.6.1 Outgoing Call Restrict If you try to make an outgoing call while outgoing call restrict is enabled, then you will hear warning tone after dial time-out. Outgoing Call restrict feature is disabled as a factory setting. 1. Pick up the handset. 2. Press <*>, <*> and <0>, <6>. 3. Press 4 digits Lock Code Number (Default Number is 0000 (four times zero)). Note: If the code is correct, it sounds confirmation beep.
CDMA WLL User’s Guide HTT-800A out. Long Call restrict feature is disabled as a factory setting. 1. Pick up the handset. 2. Press <*>, <*> and <1>, <2>. 3. Press 4 digits Lock Code Number. (Default Number is 0000 (four times zero)). Note: If the code is correct, it sounds confirmation beep. If not, it returns to the standby mode with error beep. 4. Press <*> to set long call restrict or Press <#> to release long call restrict.
CDMA WLL User’s Guide HTT-800A confirmation beep. If not, it returns to the standby mode with error beep. 4. Press <*> to set international call restrict or Press <#> to release international call restrict. Note: If someone tries to make a call when international call restriction is set, it sounds restriction beep. 4.6.
CDMA WLL User’s Guide HTT-800A 4.7 Lock Code Used when you wish to change the lock code of the terminal. The programmed lock code prevents the terminal from being operational to any other people without your permission. This feature can be disabled and enabled through simple keypad number code entry. When you first buy the phone, the lock number is 0000. 1. Pick up the handset. 2. Press <*>, <*> and <0>, <7>. 3. Press 4 digits Look Code Number (The default lock code is preset to 0000 at the factory).
CDMA WLL User’s Guide HTT-800A 4.8 Reset Reset the terminal back to the initial service status of factory pre-programmed state (Default). This feature can be disabled and enabled through simple keypad number code entry. 1. Pick up the handset. 2. Press <*>, <*> and <1>, <0>. 3. Press 4 digits Lock Code Number. (The default lock code is preset to 0000 at the factory.) Note: If the code is correct, it sounds confirmation beep. If not, it returns to the standby mode with error beep. 4. Press <*>. 5.
CDMA WLL User’s Guide HTT-800A pressed until press <*>. 4. Press <*>. 5. Wait until you hear confirmation beep. 4.10 Data Service Using USB or RS-232 Cable, you can connect this model to PC for Internet, PC Communication and/or G3 Fax communication, if your service provider provides Wireless Data Communication Service. Refer Section 7 for G3 Fax Refer Section 8 for Data Service 4.
CDMA WLL User’s Guide HTT-800A 4.12 Authentication Function (Optional) The Authentication Key function prevents the owner’s phone number from being cloned by others. The phone has its own authentication key function. This will prohibit any illegal use of the phone. Your service provider will need to register your phone using this authentication function.
CDMA WLL User’s Guide HTT-800A 5. Supplementary Functions 5.1 Call Functions 5.1.1 Speed Dial This model will store up to 200 phone numbers using 3 digit addresses (001-200). The stored number in the Phonebook allows a call to be placed by pressing the three digit address. 1) Speed Dial Function On / Off You can set the Speed Dial function by entering the following functions. 1. Press “36*#011*” to Speed Dial On 2.
CDMA WLL User’s Guide - HTT-800A If the saved address is two digits, pick up the handset and press the first digit and then press the second digit and hold it down then a call is made. - If the saved address is three digits, pick up the handset and press the first digit , second digit and then press the third digit and hold it down then a call is made. Note : If you attempt a Speed Dialing while the Speed Dial Function is OFF, an error tone will sound to indicate wrong operation. 5.1.
CDMA WLL User’s Guide HTT-800A 5.1.3 Emergency call When emergency call number is connected once, it will not be terminated unless the called party disconnects the call (Emergency Call Hold Service). Therefore even caller hangs up the telephone, the line will be still connected, so if the caller picks up the telephone again, he can continue talking.
CDMA WLL User’s Guide HTT-800A 1. Pick up the telephone handset and Press “36*#02” 2. Press “3” to enter Emergency call number store step Note: If you want to Delete at this point, Press “4” to save (except 5, 6 step). If you want to Delete All at this point then Press “5” to save (except 4, 5, 6 step). 3. Press “Lock code” (4 digits) 4. Press one of “Memory number” for Emergency call number(01-03) 5. Press the “digits” (Max 32 digits) 6.
CDMA WLL User’s Guide HTT-800A delayed manner between 4-8 seconds (sending waiting time), depending on your default value, after you pick up the handset. Original default value is 6 seconds. - Immediate Hot Line: The call will be made as soon as you pick up the handset. 3. The Hotline function overrides any other functions. 1) Hot Line function on/off 1. Pick up the telephone handset 2. Press “36*#031” to Timed Hot Line On Or “36*#032” to Immediate Hot Line On Or “36*#033” to Hot Line Off 3.
CDMA WLL User’s Guide HTT-800A 5. Press <*> to save. Note: If the Hot Line function is in the Immediate Hot Line mode, a call may not be made to another number. In this case, to make a call to another number, change the setup mode. Pick up the handset and press <#> within 1 second and go to the setup mode, and deactivate the Hot Line function. 5.2 Pay Phone Interface This terminal supports the Metering Pulse (12kHz, 16kHz) and the Polarity Reverse for the PCO Interface. 1.
CDMA WLL User’s Guide HTT-800A 5.3 Phone Book 5.3.1 Storing Phone Numbers 1. Pick up the telephone handset and Press “36*#051” 2. Press the 3 digit memory address (001~200). 3. Press the phone numbers (Max 32 digits). 4. Press <*> to store. 5.3.2 Deleting Phone Numbers 1) Deleting a Number 1. Pick up the telephone handset and Press “36*#052” 2. Press the 3 digit memory address to be deleted. 3. Press <*> to delete 2) Deleting All Numbers 1. Pick up the telephone handset and Press “36*#053” 2.
CDMA WLL User’s Guide HTT-800A There are two detailed settings available, for regular level voice privacy mode and for reinforced voice privacy mode. 1. Press “36*#06”. 2. Press <1> for Enhanced Voice Privacy mode or <2> for Standard Voice Privacy mode. 3. Press <*> to save. 5.5 Ringer Frequency & Cadence Control This function is used to control the ringer frequency and cadence. Select the frequency first and then select the cadence. Default setting is 20Hz, 1 sec on – 2sec Off. 5.
CDMA WLL User’s Guide HTT-800A Sec Off - 3: 1 Sec On – 4.5 Sec Off - 4: 1 Sec On – 4 Sec Off - 5: 0.25 Sec On – 0.25 Sec Off - 0.25 Sec On – 1.25 Sec Off - 6: 2 Sec On – 4 Sec Off 3. Press <*> to save. 5.6 Dial Tone Frequency Control This function is used to select the dial sent from the handset. 1. Press “36*#09”. 2. Select a desired tone from 1(350 + 440Hz), 2(400Hz), 3(425Hz), 4(450Hz), 5(312.5 + 412.5Hz). 3. Press <*> to save. 5.
CDMA WLL User’s Guide HTT-800A Note: Hook-flash is accomplished in a call through either pressing the dedicated hook-flash key which is available on some phones or through a rapid single press of the hang-up mechanism upon which the handset rests when the phone is hung up. 5.8 ROH (Receiver off Hook) If the telephone equipment remains “off-hook”, meaning that the handset is left off of its cradle as it would be when you hang up, a ROH tone emits from the receiver for a period of 60 seconds.
CDMA WLL User’s Guide HTT-800A This terminal has 10 Deny dial numbers (1~10), and max. 32 digits can be stored in each Deny dial number. This terminal has 10 Permit dial number (1~10), and max. 32 digits can be stored in each Permit dial number. If you set Emergency call, the emergency number is not applied to this restrict call. 5.9.1 Set Restrict Call Level 1. Press “36*#11”. 2. Press restrict level (1~2) - 1: No restriction - 2 : Restriction 3. Press “LOCK code” (4 digits). 4. Press <*> to save.
CDMA WLL User’s Guide HTT-800A 3. Press “LOCK code” (4 digits). 4. Press one of “Memory number” for permit dial number (01~10). 5. Press the “digits” (Max. 32digits). 6. If you want to store more Permit Dial Numbers continue from step2 7. Press <*> to save. 5.9.3 Storing (Deleting) the Deny Dial Number (Restricted dial number) 1. Press “36*#13”. 2. Press “1” to enter Deny Dial Number store step. Note: If you want to Delete at this point, Press “2” to save (except 5, 6 step).
CDMA WLL User’s Guide HTT-800A 6. System Functions 6.1 Call Waiting Call Waiting is a feature, which enables you to be alerted to a second incoming call while you are on the first call of your telephone. You have the option of responding to the second call while putting the first call on hold or you can disable the call waiting option during a particular call. Contact your service provider to activate or deactivate Call Waiting. 6.
CDMA WLL User’s Guide HTT-800A 7. FAX Functions 7.1 FAX Set-up 1) To send or receive analog fax messages, the FWT should be equipped with an analog fax module, connected to a conventional fax machine with the FWT, as shown in section 2.3 Note: When you use a fax function and terminal should be connected to AC/DC adapter. Other wise it may indicate Low battery warning. 7.2 Sending FAX Message You can send and receive fax massages using a fax machine connected to the FWT. 1) Dual dialing Method 1.
CDMA WLL User’s Guide HTT-800A 2) Per-digit Method 1. Load documents to send into a fax machine. 2. Pick up the handset or press On-hook button of the fax machine. 3. Press <*>, <8>, <9>, <*> and destination fax number in sequence. The FWT will make a call automatically. 7.3 Receiving G3 FAX Message You can set the FWT to “Always Mode” or “Once” fax reception mode. 1. Pick up the handset or press On-hook button of the fax machine. 2.
CDMA WLL User’s Guide HTT-800A mode to voice call mode. - Pick up the handset or press On-hook key. - Press <*>, <*>, <0>, <9>, <7> in sequence. - Wait for a confirmation dial tone. 7.4 Receiving PC FAX message You can set the FWT to “Always” or “Once” Mode fax reception mode. 1. Pick up the handset or press On-hook key. 2. Press <*>, <*>, <0>, <9>, <3> to set “Always Mode”. Press <*>, <*>, <0>, <9>, <4> to set “Once Mode”. 3. Wait for a confirmation dial tone. 4.
CDMA WLL User’s Guide HTT-800A 8. Data Service 8.1 For Windows 98, Windows 2000 8.1.1 Setting the phone to DS (Data Service) Data Service mode setting ) Press 36*#103* (Data Service through USB Cable) from phone keypad. ) Press 36*#102* (Data Service through RS-232 Cable) from phone keypad. FWT and PC Setting Packet data Dial up Number Modem B.
CDMA WLL User’s Guide HTT-800A Notes: 1. XXXX (where XXXX is depends on Service provider location). 2. Below Setup is shown for Packet data, for circuit data Dial up Number and Modem baud rate to be changed accordingly. 8.1.2 Setting a USB driver in PC Users must designate a proper standard modem to a proper serial port (COM port) of their computers. If you connect PC with the USB cable, you will be displayed with the following message. ) Click on the Next button.
CDMA WLL User’s Guide HTT-800A ) Check the box next to where it says, “Search for a suitable driver for my device (recommended)” and then click on the Next button.
CDMA WLL User’s Guide HTT-800A ) Check the box next to where it says, “CD – ROM drives” and then click on the Next button. ) Click on the Next button. ) Click on the Finish button.
CDMA WLL User’s Guide HTT-800A ) This is not over. You have to continue to setup USB Driver. The following window appears automatically. Click on the Next button.
CDMA WLL User’s Guide HTT-800A ) Check the box next to where it says, “Search for a suitable driver for my device (recommended)” and then click on the Next button. ) Check the box next to where it says, “CD – ROM drives” and then click on the Next button.
CDMA WLL User’s Guide HTT-800A ) Click on the Next button. ) Click on the Yes button. ) Click on the Finish button.
CDMA WLL User’s Guide HTT-800A ) This is the last setup. The following window appears automatically too. Click on the Next button.
CDMA WLL User’s Guide HTT-800A ) Check the box next to where it says, “Search for a suitable driver for my device (recommended)” and then click on the Next button. ) Check the box next to where it says, “CD – ROM drives” and then click on the next button.
CDMA WLL User’s Guide HTT-800A ) Click on the Next button. ) Click on the Finish button.
CDMA WLL User’s Guide HTT-800A manager]. You will see a ‘Modems’ icon. You can check if USB Driver setup is right or not. You have completed the setup for USB Driver. From now, you can use the USB, connecting the FWT (WLL). 8.1.3 Setting a Standard Modem in PC ) Click [Start] → Double-click [Phone and Modem Options] → click [Modem]. ) Select a COM port and click Properties.
CDMA WLL User’s Guide HTT-800A that the modem is installed properly including serial port number and data speed. If not, make a correction. Note: Maximum Speed type has many kinds. We recommend 115,200bps. And Port is properly serial port for your PC. Now, you’re ready to make a data call, using HTT Model.
CDMA WLL User’s Guide HTT-800A 8.1.4 Browsing the Internet Setting a Dial-Up Networking ) Double-click [Control panel] → Double-click [Network and Dial-up Connections] → Double-click [Make New Connection]. ) Click on the Next button.
CDMA WLL User’s Guide HTT-800A ) Check second radio button and click on the Next button. ) Check third radio button and click on the Next button.
CDMA WLL User’s Guide HTT-800A ) Check first radio button and click on the Next button. ) Input the telephone number, the designated number of your operator or ISP (ex #777). Click on the Next button.
CDMA WLL User’s Guide HTT-800A ) Enter User Name and Password. Click on the Next button. Note: User name and password will be provided by your operator or ISP. For Instance “Sktelecom” and blank can be used for User name and password respectively in Korea.
CDMA WLL User’s Guide HTT-800A ) Click on the Next button. ) Select “No” and then click on the Next button. ) Uncheck the check button and click on the Finish button.
CDMA WLL User’s Guide ) Double-click HTT-800A [Control Panel] → Double-click [Network and Dial-up Connections]. You will see a new icon.
CDMA WLL User’s Guide HTT-800A Connecting to the Internet ) Double-click Dial-up Networking icon which you made in your PC. ) Click “Dial” button. ) When connected, run the internet browser. 8.2 For Windows XP 8.2.1 Setting the phone to DS (Data Service) Data Service mode setting ) Press 36*#103*. (Data Service through USB Cable) ) Press 36*#102*. (Data Service through RS-232 Cable) 8.2.
CDMA WLL User’s Guide HTT-800A If you connect PC with the USB cable, you will see the message. ) Click on the Next button and check the box next to where it says, “Search for a suitable driver for my device (recommended)” and then click on the Next button.
CDMA WLL User’s Guide HTT-800A ) The following dialog box appears: ) Click on the Continue Anyway button.
CDMA WLL User’s Guide HTT-800A ) Click on the Finish button. ) This is not over. You have to continue to setup USB Driver. The following window appears automatically.
CDMA WLL User’s Guide HTT-800A Click on the Next button. ) The following dialog box appears: ) Click on the Continue Anyway button.
CDMA WLL User’s Guide HTT-800A ) Click on the Finish button.
CDMA WLL User’s Guide HTT-800A ) This is the last setup. The following window appears automatically too. Click on the Next button.
CDMA WLL User’s Guide HTT-800A ) Click on the Continue Anyway button. ) The following dialog box appears: ) Click on the Finish button.
CDMA WLL User’s Guide ) Double-click HTT-800A [control panel] → Double-click [system] → Click [hardware] → Click [device manager]. You will see a ‘Modems’ icon. You can check that USB Driver setup is right or not. You have Complete the setup for USB Driver. From now, you can use the USB, connecting the FWT (WLL) 8.2.
CDMA WLL User’s Guide HTT-800A Options] → click [Modem]. ) Select a COM port and click Properties. Make sure that the modem is installed properly including serial port number and data speed. If not, make a correction. Note: Maximum Speed type has many kinds. We recommend 115,200bps. You check it whether a port is properly serial port for your PC or not. Now, you’re ready to make a data call, using HTT model. 8.2.4.
CDMA WLL User’s Guide HTT-800A Internet Setting a Dial-Up Networking ) Double-click [Control Panel] → Double-click [Network Connections] → Click [view network connects] → Click [Create a new connection].
CDMA WLL User’s Guide HTT-800A ) Check first radio button and Click Next. ) Check second radio button and Click Next.
CDMA WLL User’s Guide HTT-800A ) Check first radio button and Click Next. ) Write arbitrary ISP name and Click Next.
CDMA WLL User’s Guide HTT-800A ) Enter the telephone number, the designated number of your operator or ISP (ex #777). Click Next. ) Enter User Name and Password. Click Next.
CDMA WLL User’s Guide HTT-800A your operator or ISP. ) Uncheck the check button and Click Finish. ) Double-click [Control Panel] → Double-click [Network Connections]. You will see a new icon.
CDMA WLL User’s Guide HTT-800A (Dial-up networking icon) Connecting to the Internet ) Double click Dial-up Networking icon which you made in your PC. ) Click “Dial” button. ) When connected, run the internet browser. 8.3 Data Installation Trouble Shooting 8.3.
CDMA WLL User’s Guide HTT-800A instructions. 1) Error 680: No dial tone. Make sure that the phone is in the Service State. Unless an antenna is not displayed, check the line between a phone and PC is well-connected and channel, ESN and MIN are well-put. 2) Error 691: Authentication failed. This error occurs when it cannot establish a dial up networking connection. Check user name and password are correct. 3) Error 692: Hardware failure in port or attached device.
CDMA WLL User’s Guide 6) HTT-800A Error 619 : Disconnected This error may be displayed in case of setting problem. You have to check the DS Baud rate in 3 places. 1. Setting the phone into DS Baud 2. Setting [Phone and Modem Options] into your PC in the [Control panel]. Reference to section 8.1 (in case of Window 2000, Window98), section 8.2 (Window XP) 3. Setting the [Dial- up icon] into your PC [Dial- up icon] => Properties => Configure 8.3.
CDMA WLL User’s Guide HTT-800A ) Click on “Properties” button. ) Click “Modem” and select the BAUD rate In case of Packet Data: 115,200 In case of Circuit Data: 19,200. ) Click on the “OK” button.
CDMA WLL User’s Guide HTT-800A ) Click on the “OK” button.
CDMA WLL User’s Guide HTT-800A ) Click on the “Properties” button. ) Select your COM Port (Since USB Cable is been used, select “Modem – TELSON Handset (COM4)”).
CDMA WLL User’s Guide HTT-800A ) Click on the “Configure” button. o Verify under Phone Number Column #777 is used for Packet data & XXXX is used for Circuit data (where XXXX depends on Network). o Verify Modem Baud rate, should be 115200 In case of Packet Data & 19200 in case of Circuit Data.
CDMA WLL User’s Guide HTT-800A ) Click on the “OK” button.
CDMA WLL User’s Guide HTT-800A 9. Summary Table 9.1 Advanced Functions Menu Item Process 1. One Minute Set <*>, <*> Î 01 Î <*> Alert Release <*>, <*> Î 01 Î <#> 12 Hour mode <*>, <*> Î 02 Î <1> <1> Î 2. Alarm (AM) (00:00~11:59) Î <*> 12 Hour mode <*>, <*> Î 02 Î <1> <2> Î (PM) (00:00~12:59) Î <*> 24 Hour mode <*>, <*> Î 02 Î <2> Î (00:00~23:59) Î <*> Release <*>, <*> Î 02 Î <#> 3.
CDMA WLL User’s Guide Analog Fax HTT-800A <*>, <*> Î 09 Î <1> Always mode Analog Fax <*>, <*> Î 09 Î <2> Once mode PC Fax 9. Data Rx <*>, <*> Î 09 Î <3> Always mode PC Fax <*>, <*> Î 09 Î <4> Once mode A sync Data <*>, <*> Î 09 Î <5> Always mode A sync Data <*>, <*> Î 09 Î <6> Once mode Voice mode <*>, <*> Î 09 Î <7> <*>, <*> Î 10 Î lock code(4 digits) 10. Reset Î <*> <*>, <*> Î 11 Î < 0 ~ 9> Î <*> 11. Auto Dial time Enable restrict <*>, <*> Î 12 Î lock code(4 digits) Î <*> 12.
CDMA WLL User’s Guide HTT-800A 9.2 Supplementary Functions Menu Item On 1. Speed dial Process 36*#01 Î 1 Î <*> Off 36*#01 Î 2 On 36*#02 Î 1 Î lock code(4 digits) Î ( <*> Off 36*#02 Î 2 Î lock code(4 digits) Î Store ( lock code(4 digits) ( address (01~03) ( phone number ( <*> 36*#02 ( 4 ( lock code(4 digits) ( address (01~03) ( <*> <*> <*> 2.
CDMA WLL User’s Guide HTT-800A 36*#05 Î 1 Î address (001~200) Store Î phone number Î <*> 5. Phone 36*#05 Î 2 Î address (001~200) Delete Book Î <*> 6. Voice Privacy 7. Ringer Freq. All Delete 36*#05 Î 3 Î <*> Enhanced 36*#06 Î 1 Î <*> Standard 36*#06 Î 2 Î <*> 16Hz 36*#07 Î 1 Î <*> 20Hz 36*#07 Î 2 Î <*> 25Hz 36*#07 Î 3 Î <*> 1Sec On–2 36*#08 Î 1 Î <*> On– 36*#08 Î 2 Î <*> Sec Off 0.4Sec 0.2Sec Off -0.4Sec On–2 Sec Off 8.
CDMA WLL User’s Guide No Restriction 11. Restrict Call mode HTT-800A 36*#11 Î 1 Î lock code(4 digits) Î <*> Restriction 36*#11 Î 2 Î lock code(4 digits) Î <*> Store 12. – address (01~10) Î phone number Î Restrict Call mode Permit Number 36*#12 Î 1 Î lock code(4 digits) Î <*> Delete 36*#12 Î 2 Î lock code(4 digits) Î Delete All 36*#12 Î 3 Î lock code(4 digits) Î address (01~10) Î <*> <*> Store 13.
CDMA WLL User’s Guide HTT-800A 10. Troubleshooting Guide Problems Troubleshoot the conventional wired telephone When you hear no sound after hook-off? Troubleshoot the Fixed Wireless Terminal What To Do In the event you are unable to dial or receive telephone calls, first be sure that the connection wire is properly connected to the RJ-11 phone port on the terminal and to the RJ-11 port of the telephone.
CDMA WLL User’s Guide HTT-800A When the battery LED is off Check if the battery on/off switch at the bottom of the terminal is on. The backup battery is discharged, Check the Battery Switch or freshly charged one. When the RSSI LED blinks or off Check if the antenna is connected correctly, or move the location of the terminal When the never or poor ring/sound Check you will achieve the best audio quality with only a single telephone “Off-hook” at a time Check Re-measure your cable and accordingly.
CDMA WLL User’s Guide HTT-800A 11. Specifications Frequency Tx : 824~849 MHz HTT-800A Range Rx : 869~894 MHz Channel Bandwidth CDMA 1.25 MHz RJ-11 Phone/Analog Fax port 2 Frequency Stability ± 300 Hz Tx Power Max. 0.2W Rx Power Level -104 ~ -25 dBm Temperature of operation -10℃ ~ + 55℃ Relative humidity 5% ~ + 95% Input : AC 90~300V / 50~60Hz Power Supply(Adapter) Output : DC 12V 1A Battery Capacity 3.
U.S.A. U.S.FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT INFORMATION TO THE USER NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules.