User's Manual

ManualsBrandsHansol LCD ManualsComputers & AccessoriesColor Monitor

User’s Manual 3

FCC Information

This equipment has been tested and found to comply with limits for a class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful inteference to radio

Communications. However, there is no guarantee that interference will not occur in a particular

installation.

If this equipment does cause unacceptable interference to radio and television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures.

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced Radio/TV technician for help.

User’s Manual2

Introduction

Package 4

Features

Safety Information

Power Management System 7

Installation

Connection to your computer 7

Pin assignment table D-Sub mini 15 pin connector 8

Controls

Function of controls 8

OSD Menu 9

Troubleshooting

Troubleshooting Guide 13

Specifications

Electrical specifications 14

Mechanical specifications 14

Environmental specifications 14

Appendix

Preset timings 15

English

Summary of content (7 pages)

PAGE 1
FCC Information This equipment has been tested and found to comply with limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inteference to radio Communications.
PAGE 2
Introduction Introduction Caution Features ENGLISH Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 19-inch(18 inch visual)high performance display color monitor Warning If this equipment has more than one interface connector, do not leave cables connected to unused interfaces.
PAGE 3
Introduction / Installation Introduction Safety information For 120Volt applications use only UL listed detachable power cord with NEMA configuration 5-15P type(parallel blades) plug cap. For 240Volt applications use only UL listed detachable power cord with NEMA configuration 6-15P type(tandem blades) plug cap. Use only a power source and connection appropriate for the monitor as indicated on the marking label.
PAGE 4
Installation / Controls Controls Additional front controls Pin assignment table D-Sub Mini 15pin connector Assignment Red Video Green Video Blue Video Frame Ground Ground Red Video Ground Green Video Ground Blue Video Ground N.C ID Monitor Ground SDA H-Sync V-Sync SCL Power Switch : Turn the monitor power on or off, When the power is on, the LED is lit. The 15-Pin D-sub connector (male) of the signal cable (IBM Systems) 1 ENGLISH Pin No.
PAGE 5
Controls Controls Position and size Menu control guide Contrast Menu / : Increase or decrease the Contrast. : Exit to the main menu. : Refer to ENGLISH : Proceed to the Contrast menu. MENU : Toggle Horizontal and Vertical directly. Geometry Menu Brightness Menu The Geometry controls allow you to adjust the curvature or angle of displayed image. / : Proceed to the Brightness menu. : Increase or decrease the Brightness . Position Menu Atfer choosing , push MENU button.
PAGE 6
Controls Troubleshooting Language Menu Troubleshooting guide ENGLISH After choosing , push MENU button. : Select the language. If your monitor is not performing properly, please use the following troubleshooting chart for quick solutions to common problems. Problem Possible cause Remedy OSD Position Menu After choosing , push MENU button. MENU : Push this button again & again to change the H/V-OSD position. : Move the OSD position left or down. : Move the OSD position right or up.
PAGE 7
Specifications Appendix Preset Timings Electrical Specifications D19BL 19 , 90 deflection, Flat CRT Horizontal Dot pitch 0.20mm CRT Surface Anti-Reflection & Anti-Static Sync Input Signal This Monitor D19BL has preset modes for the 10 most popular industry standards for Plug and Play capability. Horizontal H/V Separate, TTL, positive/negative Video Video Sync Sync H/V Composite, TTL, positive/negative Video Scanning frequency Horizontal Vertical Maximum Resolution RGB Analog (0.