User’s Guide 920D+(D19BL) COLOR MONITOR Table of Contents Regulatory Information .......................................................................................................................... 2 Introduction Features ................................................................................................................................................... 3 Controls OSD Controls ........................................................................................................
Color Monitor Regulatory Information - FCC Information This equipment has been tested and found to comply with limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment can generates, uses, and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Color Monitor Introduction - Features 19-inch (18 inch visual) high performance display color monitor Automatically scans frequencies from - Horizontal frequency: 30 to 96KHz - Vertical frequency: 50 to 160Hz Compatible with VGA, SVGA, VESA, MAC Standards and maximum resolution modes up to 1600 × 1200 Supports VESA flicker free modes including 85Hz refresh rate.
Color Monitor Controls - OSD controls The OSD apears on the screen when you press MENU button. “ON SCREEN MENU” controls include the following extended controls such as Size, Position, Geometry Distortion, Color Temp., Degauss, Moire on & off, Language, OSD-Position, Recall, Cont. & Brt., etc. Accessing OSD Press MENU Button. － : Direct Brightness access. + : Direct Contrast access. EXIT from OSD : Press this ( ) button in the main menu and submenu.
Color Monitor Controls - OSD Menu OSD MENU 1. NO OSD CONTROL •－ •+ • Proceeds to NO.3 Proceeds to NO.4 No meaning 2. MAIN MENU • － + Moves to function to choose. • Exit the OSD controls. • MENU : Proceed to the selected menu. 3. BRIGHTNESS •－ •－+ Proceed to the Brightness menu. Increases or decrease the Brightness. 4. CONTRAST •+ Proceed to the Contrast menu. • － + Increases or decrease the Contrast position and size Menu control guide 5. H/V-POSITION : exit to the main menu.
Color Monitor 6. H/V-SIZE • After choosing , push MENU button. • MEUN : Push this button again & again to change the H/V-size. • － : Decrease the Horizontal or Vertical size of the image. • + : Increase the Horizontal or Vertical size of the image. The Geometry controls allow you to adjust the curvature or angle of displayed image. 7. GEOMETRY • After choosing , push MENU button. • Pincushion : Increase or decrease the curvature of the sides either inward or outward.
Color Monitor 9. LANGUAGE • After choosing , push MENU button. • － / + : Select the language. 10. OSD POSITION • After choosing , push MENU button. • MENU : Push this button again & again to change the H/V-OSD position. • － : Move the OSD position left or down. • + : Move the OSD position right or up. 11. COLOR TEMP ※ Presetting : Select the desired color setting. The bar is replaced by the color setting choice. " USER, 6500k, 9300k " Color adjustment is available only in USER mode.
Color Monitor Power Management Feature The monitor is equipped with a power saving circuit that confirms to the world-standard Display Power Manager Signalling (DPMS) mode of Video Electronics Standard Association(VESA). The power management feature requires that the video card of the computer should support DPMS function. Status LED Sign Power Consumption Normal mode Green ON 110 Watts Stand-by mode Green Blinking(0.
Color Monitor Specifications ITEM 920D+(D19BL) CRT Type 19", 90° deflection, FLAT CRT Horizontal Dot pitch 0.20mm CRT Surface Non-glare, Anti-Reflection & Anti-Static Sync. H/V Separate, TTL, positive/negative H/V Composite, TTL, positive/negative Video RGB Analog (0.7Vp-p), positive 75 Ω Terminated Horizontal 30KHz~96KHz (Automatically) Vertical 50Hz~160Hz (Automatically) Input Signal Scanning frequency Maximum Resolution 1600Dots x 1200Lines (Non-interlace) Pixel Clock(Max.
Color Monitor Pin assignment table D-Sub Mini 15pin connector Pin No. Assignment 1 Red Video 2 Green Video 3 Blue Video 4 Frame Ground 5 Ground 6 Red Video Ground 7 Green Video Ground 8 Blue Video Ground 9 N.
Color Monitor Troubleshooting Problem No picture Solution Check that the AC cord is correctly connected. Check that the AC socket is live by plugging in another piece of equipment. Power switch and computer power switch should be in position. Ensure that the signal cable is properly connected to the video card or PC. Ensure that the video card is securely seated in the PC. Check the connector for bent or pushed-in pins.
User’s Guide COLOR MONITOR Visit for more Information www.hansolel.co.
Color Monitor Table of Contents Introduction Good Posture Guide ........................................................................................................................................... 2 Safety Information ............................................................................................................................................... 3 Package ..................................................................................................................................
Color Monitor Introduction - Safety infomation To prevent damage or loss, please read this warning carefully. When connecting/disconnecting the plug, pull out the plug itself, and never pull the cord to prevent fire caused by short. To prevent electric shock, do not connect/disconnect the plug with wet hand. To prevent fire, do not connect a large number of equipments in a single line.
Color Monitor Install the monitor near an outlet that you can reach easily. Disconnect the product by grasping the plug firmly and pulling in from the outlet. Never disconnect it by pulling the cord. Slots and openings in the cabinet are provided for ventilation; these openings must not be blocked or covered. Never push objects of any kind into cabinet slots or other openings. Never insert anything metallic into the monitor openings.
Color Monitor Introduction - Package Congratulations on your purchase of this top quality color monitor! The items illustrated below are contained in the carton. First, be sure that your carton includes all of them. If any items are missing or damaged, please contact your local dealer or supplier. UK Display Monitor Attached Signal Cable U.S.
Color Monitor Introduction - Connection to your computer CAUTION Ensure that both the PC and the display monitor are switche off. IBM ① Mac ② To attach the monitor to your system, as shown in the following illustrations. 1. Insert the AC power cord ② into monitor and then into an AC power outlet. 2. Connect the signal cable ① to the 15pin graphics connector of the system and tighten the fastening screws. 3. To turn on the monitor, push the power switch.
Color Monitor Installing Monitor Driver - Automatic Installation - Manual Installation (Windows 2000) 1. Insert the CD to the CD-ROM driver. 2. Double-click “Install.exe”. 3. Select the model and click “OK” button. 4. Select inf file, and then click “OK” button. 5. Click “Exit” button to close the installation. 1. Insert the CD to the CD-ROM driver. 2. Click ‘My Computer’ and follow the procedure below. ① Click 'Control Panel'. ② Click ‘Display’. ③ Click ‘Settings’. ④ Click ‘Advanced..’.
Color Monitor ⑩ Click ‘Display a list of all...’. ⑫ Click ‘Have Disk...’ ⑪ Click ‘Next>’. (ex : H711, 730ED...) ⑭ Click ‘Next>’. ⑮ Click ‘Next>’ (ex : H711, 730ED...) (ex : H711, 730ED...) ⑬ Select the driver and click ‘OK’. ● Click ‘Finish’. (ex : H711, 730ED...) 3. Select “Exit” if the monitor model is changed, and then reboot the Windows.
Color Monitor (Windows XP) Microsoft ® Windows ® XP Operating System 1. Insert CD into the CD-ROM driver. 2. Click "Start" → "Control Panel" then click the "Appearance and Themes" Icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced..". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab 5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will..
Color Monitor (Windows 95) Microsoft ® Windows ® 95 Operating System .First determine the Windows 95 version installed on your computer by right-clicking the My Computer icon on PC and selecting Properties. The version number is listed under System. Perform the steps for the appropriate version. Version 4.00.950A 1. Click Start, Settings, Control Panel, and then double-click "Display" icon. 2. In the "Display Properties" window, click the "Settings" tab and click "Change Display Type". 3.
Service Center EUROPE Country ASC Tel Country ASC Tel U. K Pulse Service Centre Ltd. 44-(0)-870-013-4470 Hungary Profit Service Center Kft. 36 1 399 0405 Germany BITRONICS GmbH 49-3634-683313 Bulgaria RTS 359-2-971-2020 France DATEX 33-1- 69- 310101 SWITZERLANDS TPA PANATLANTIC AG 41 1 886 10 16 Spain FREE ELECTRONICA S.A 34 91 6774787 SLOVAKIA BGS-Distribution a.
