9 Printed on the recyclable paper Printed in Korea Part No.
INFORMATION TO USER : This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Good Posture Guide Parts Place the monitor to face the user and then adjust the monitor angle. Take a break (for about 10 minutes) at every hour during the work with monitor. Refer to the following figure to take the correct posture. about 50cm Look down the monitor below the horizon. Adjust the monitor to prevent reflection. LCD Monitor Relax shoulders and arms, and sit back on the chair. Adjust the monitor stand to acquire required angle.
Connection to Signal Source Basic Connection The range of control Angle How to Adjust the Stand Port for AC power cable Port for Audio cable from audio source. Port for Head Phone or External Speaker Port for signal cable from DVI signal source. Kensington Lock Port for signal cable from analog signal source.
Installing Monitor Driver Run (Click) "Install" at Floppy Diskette driver and select the model name to set the optimum display in Window 95, 98 or 2000, XP. Use the Driver provided. Automatic Installation 1. Insert the Diskette to the Floppy Diskette driver. 2. Double-click "Install.exe". 3. Select the model and click "OK" button. 4. Select inf file, and then click "OK" button. 5. Click "Exit" button to close the installation. Click 'Advanced..'. Click 'Monitor'. Click 'Display a list of all...'.
Name and Function of Front Front panel Functions Power button Power button is located in the lower center of the Front Bezel. You can push the button to turn on/off the power. Power Indicating LED Dark : Power off Green : Normal mode Green blinking : DPMS mode or Check Signal Cable mode. On Screen Display (OSD) Function Button OSD buttons on the front of bezel perform the following functions.
Power Management Feature The monitor is equipped with a power saving circuit that confirms to the world-standard Display Power Manager Signalling (DPMS) mode of Video Electronics Standard Association (VESA). The power management feature requires that the video card of the computer should support DPMS function. Status LED Sign Power Consumption Normal mode Green ON Normal Power DPMS mode Green Blinking Input Source MENU SELECT 1. Press the MENU button to access main menu. 2.
Image Brightness &Contrast MENU SELECT 1. Press the MENU button to access main menu. to move Brightness and Contrast ICON. 2. Use 3. Press SELECT button into the submenu. Brightness SELECT 1. Use to move Brightness ICON. 2. Press SELECT button to select it. 3. Use to adjust the brightness. SELECT MENU 1. Press the MENU button to access main menu. 2. Use to move Image ICON. 3. Press SELECT button into the submenu. Horizontal Position SELECT 1. Use to move H-Position ICON. 2.
Preset Color Clock Phase MENU SELECT 1. Press to move Clock Phase ICON. 2. Use SELECT button to select it. 3. Use to correct fine trembling or Video noise. 1. Use to select the 6500K, and 9300K. 2. Press the Menu button to return previous state. 6500K : Reddish white User Color Clock SELECT SELECT to move Clock ICON. 1. Use 2. Press SELECT button to select it. 3. Press or to remove vertical noise. ( Adjusting clock phase is required after the adjustment of clock.) SELECT 1.
Language MENU SELECT 1. Use to move Language ICON. 2. Press SELECT button to select it. 3. Use to select language. Factory Auto-Config Reset SELECT SELECT 1. Use to move OSD H-Position ICON. 2. Press SELECT button to select it. 3. Use to adjust OSD left or right. OSD V-Position SELECT 1. Use to move the Factory Reset ICON. 2. Press SELECT button to return to default setting. Auto-Config Information MENU OSD H-Position 1. Use to move OSD V-Position ICON. 2. Press SELECT button to select it. 3.
Sound Auto-Config (Option) MENU SELECT or VOL BUTTON 1. Use to move Sound ICON. 2. Press SELECT button to select it. to control volume. 3. Use 4. Press MENU button to return previous state. 1. When change DVI display into Analog display, select source button located in the left. Analog display will be showed after Analog input message. 2. When change Analog display into DVI display, select source button located in the left. DVI display will be showed after DVI input message. 3.
Pin assignment table D-Sub Mini 15pin connector Specification Model Pin No. 1 2 3 4 5 6 7 8 Assignment Red Video Green Video Blue Video N.C Ground Red Video Ground Pin No. 9 10 11 12 13 14 Assignment 5V Input Ground Ground SDA H.Sync V.Sync Green Video Ground Blue Video Ground 15 SCL 1 5 10 6 11 LCD Panel 15 15pin D-Sub H950 (B19AF Type Amorphous active matrix super TFT LCD Screen Size 48.3cm (Diagonal) Maximum Resolution 1280 X 1024 @ 75 Hz Pixel Range 0.294 mm X 0.
Troubleshooting Power LED is dark. No picture. OSD, "check signal." is displayed on the screen. Message, "check cable." is displayed on the screen. Screen looks to be run down. Check the power connection. (Refer to page 4) Color is irregular. Adjust COLOR at User Mode in OSD Color Menu. Check the computer power is on. Double images or 'ghosts'. Check the resolution and frequency of computer and video card, and set up again in reference to the current monitor mode and standard signal mode table.
Warning To prevent damage or loss, please read this warning carefully. When connecting/disconnecting the plug, pull out the plug itself, and never pull the cord to prevent fire caused by short. To prevent electric shock, do not connect/disconnect the plug with wet hand. If you see smoke or smell something burning, stop using the unit, switch off the power, pull out the plug, and then contact your local service station. To prevent fire, do not connect a large number of equipments in a single line.
