User’s Guide H750D(B17DF) TFT-LCD Monitor Table of Contents Regulatory Information .......................................................................................................................... 2 Introduction Package ....................................................................................................................................................3 The range of control Angle ....................................................................................................
TFT-LCD Monitor Regulatory Information - FCC Information This equipment has been tested and found to comply with limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment can generates, uses, and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
TFT-LCD Monitor Introduction - Package Congratulations on your purchase of this top quality color monitor! The items illustrated below are contained in the carton. First, be sure that your carton includes all of them. If any items are missing or damaged, please contact your local dealer or supplier. UK LCD Monitor Signal Cable (Analog) U.S.
TFT-LCD Monitor . Introduction - Connection to Basic Connection Signal Source ① Port for AC power cable. ② Port for Audio cable from audio source. ③ Port for Head Phone or External Speaker. ④ Port for signal cable from DVI signal source. ⑤ Kensington Lock. ⑥ Port for signal cable from analog signal source. ① ②③④ ⑤ ⑥ 1. Use 220V or 110 V.(Free Voltage) 2. Connect monitor and Signal Source via Signal cable. 3. Power on the monitor and computer. 4. Connection is finished.
TFT-LCD Monitor Controls - Front panel SOURCE BUTTON VOL/MUTE BUTTON / + BUTTON MENU/EXIT BUTTON / – BUTTON SELECT/AUTO BUTTON POWER BUTTON (Power indicating LED) - Functions Power button Power button is located in the lower center of the Front Bezel. You can push the button to trun on/off the power. Power Indicating LED Dark : Power off Green : Normal mode Green blinking : DPMS mode or Check Signal Cable mode.
TFT-LCD 모니터 Controls - Adjusting OSD Input Source MENU – + SELECT 1. Press the MENU button to access main menu. 2. Use –,+ to move Input source ICON. 3. Press SELECT button into the submenu. Digital Input ◈ Input Source Submenu – + SELECT 1. Use –,+ to move Digital input ICON. 2. Press SELECT button to select DVI display. Analog Input ◈ Input Source Submenu – + SELECT 1. Use –,+ to move Analog input ICON. 2. Press SELECT button to select Analog display.
TFT-LCD 모니터 Brightness ◈ Brightness & Contrast Submenu – + SELECT – + 1. Use –,+ to move Brightness ICON. 2. Press SELECT button to select it. 3. Use –,+ to adjust the brightness. Contrast ◈ Brightness & Contrast Submenu – + SELECT – + 1. Use –,+ to move Contrast ICON. 2. Press SELECT button to select it. 3. Use –,+ to adjust the contrast. Clock Phase MENU – + SELECT 1. Press the MENU button to access main menu. 2. Use –,+ to move Clock Phase ICON. 3. Press SELECT button into the submenu.
TFT-LCD 모니터 Vertical Position ◈ Clock Phase Submenu – + SELECT – + 1. Use –,+ to move V-Position ICON. 2. Press SELECT button to select it. 3. Use –,+ to adjust display upward or downward. According to the characteristic of video card, control range can be changed. Clock Phase ◈ Clock Phase Submenu – + SELECT – + 1. Press –,+ to move Clock Phase ICON. 2. Use SELECT button to select it. 3. Use –,+ to correct fine trembling or Video noise. Clock ◈ Clock Phase Submenu – + SELECT – + 1.
TFT-LCD 모니터 Preset Color ◈ Color Submenu – + MENU 1. Use –,+ to select the 6500K, and 9300K. 2. Press the Menu button to return previous state. ※ 6500K : Reddish white / 9300K : Bluish white User Color ◈ Color Submenu – + SELECT – + MENU 1. Use –,+ to move User color ICON. 2. Press SELECT button to select it. 3. Use –,+ to Shift the color what you want. 4. Use select button to select it. 5. Use –,+ to increase or decrease each color. 6. Press the menu button to return previous state.
TFT-LCD 모니터 Factory Reset ◈ Special Submenu – + SELECT 1. Use –,+ to move the Factory Reset ICON. 2. Press SELECT button to return to default setting. Information ◈ Special Submenu MENU – + SELECT 1. Use –,+ to move the Information ICON. 2. Press SELECT button to select it. You can know display information * Accoding to the characteristic of video card, display information can be incorrect. OSD H-Position ◈ Special Submenu – + SELECT – + 1. Use –,+ to move OSD H-Position ICON. 2.
TFT-LCD 모니터 OSD Time ◈ Special Submenu – + SELECT – + 1. Use –,+ to move OSD Time ICON. 2. Press SELECT button to select it. 3. Use –,+ to adjust OSD display time. Sound(Option) MENU – + SELECT or VOL BUTTON 1. Use –,+ to move Sound ICON. 2. Press SELECT button to select it. 3. Use –,+ to control volume. 4. Press MENU button to return previous state. - HOT KEY ANALOG & DVI When change DVI display into Analog display, select source button located in the left.
TFT-LCD Monitor Power Management Feature The monitor is equipped with a power saving circuit that confirms to the world-standard Display Power Manager Signalling (DPMS) mode of Video Electronics Standard Association(VESA). The power management feature requires that the video card of the computer should support DPMS function. Status LED Sign Power Consumption Normal mode Green ON DPMS mode Green Blinking Normal Power 1 W or Below(Analog)/ 3.
TFT-LCD Monitor Specifications ITEM LCD Panel Synchronization Video Input H750D(B17DF) Type Amorphous active matrix super TFT LCD Screen Size 43.2cm (Diagonal) Maximum Resolution 1280 X 1024 @ 75Hz Pixel Range 0.264mm X 0.264mm Display Colors 16.7M Color Contrast Ratio 350 : 1 Viewing Angle 70° / 70° / 60° / 60° (Left / Right / Up / Down) Response Time 25 msec Luminance 250 cd/m2 Horizontal Frequency 79.9 kHz(Max.) Vertical Frequency 75 Hz-Analog / 72Hz-DVI(Max.
TFT-LCD 모니터 Pin assignment table D-Sub Mini 15pin connector Analog Cable Pin No. Assignment Pin No. Assignment 1 Red Video 9 5V Input 2 Green Video 10 Ground 3 Blue Video 11 Ground 4 N.C 12 SDA 5 Ground 13 H-Sync. 6 Red Video Ground 14 V-Sync. 7 Green Video Ground 15 SCL 8 Blue Video Ground 1 5 10 6 11 15 (15 pin D-Sub) DVI Cable Pin No. Assignment Pin No.
TFT-LCD Monitor Troubleshooting Problem Solution Power LED is dark. No picture. Check the power connection (Refer to Introduction) OSD, “check signal.” is displayed on the screen. Check the computer power is on. Message, “check cable.” is displayed on the screen. Check the signal cable between monitor and computer. (Refer to Introduction) Screen looks to be run down. Perform Auto-config. Remove attaches to the signal line(Video extension cable and others) and switch on.
User’s Guide TFT-LCD MONITOR Visit for more Information www.hansollcd.
TFT-LCD Monitor Table of Contents Introduction Good Posture Guide ............................................................................................................................................2 Safety Information ...............................................................................................................................................3 Connection to Signal Source .............................................................................................................
TFT-LCD Monitor Introduction - Safety infomation To prevent damage or loss, please read this warning carefully. When connecting/disconnecting the plug, pull out the plug itself, and never pull the cord to prevent fire caused by short. To prevent electric shock, do not connect/disconnect the plug with wet hand. To prevent fire, do not connect a large number of equipments in a single line.
TFT-LCD Monitor Install the monitor near an outlet that you can reach easily. Disconnect the product by grasping the plug firmly and pulling in from the outlet. Never disconnect it by pulling the cord. Slots and openings in the cabinet are provided for ventilation; these openings must not be blocked or covered. Never push objects of any kind into cabinet slots or other openings. Never insert anything metallic into the monitor openings.
TFT-LCD Monitor Introduction - Connection to Basic Option Signal Source ① Port for 12V DC cable from adapter or stand. ② Port for signal cable from signal source. ③ Port for AC power cable. ①②③ ①② Basic Option General For Macintosh Adapter for Macintosh(Optional) Refer to the table on the rear side of the optional Macintosh adapter and adjust DIP switch by the resolution. 1. Use 220V or 110 V.(Free Voltage) 2.
TFT-LCD Monitor Installing Monitor Driver - Automatic Installation - Manual Installation (Windows 2000) 1. Insert the CD to the CD-ROM driver. 2. Double-click “Install.exe”. 3. Select the model and click “OK” button. 4. Select inf file, and then click “OK” button. 5. Click “Exit” button to close the installation. 1. Insert the CD to the CD-ROM driver. 2. Click ‘My Computer’ and follow the procedure below. ① Click 'Control Panel'. ② Click ‘Display’. ③ Click ‘Settings’. ④ Click ‘Advanced..’.
TFT-LCD Monitor ⑩ Click ‘Display a list of all...’. ⑫ Click ‘Have Disk...’ ⑪ Click ‘Next>’. (ex : H711, 730ED...) ⑭ Click ‘Next>’. ⑮ Click ‘Next>’ (ex : H711, 730ED...) (ex : H711, 730ED...) ⑬ Select the driver and click ‘OK’. ● Click ‘Finish’. (ex : H711, 730ED...) 3. Select “Exit” if the monitor model is changed, and then reboot the Windows.
TFT-LCD Monitor (Windows XP) Microsoft ® Windows ® XP Operating System 1. Insert CD into the CD-ROM driver. 2. Click "Start" → "Control Panel" then click the "Appearance and Themes" Icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced..". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab 5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will..
TFT-LCD Monitor (Windows 95) Microsoft ® Windows ® 95 Operating System .First determine the Windows 95 version installed on your computer by right-clicking the My Computer icon on PC and selecting Properties. The version number is listed under System. Perform the steps for the appropriate version. Version 4.00.950A 1. Click Start, Settings, Control Panel, and then double-click "Display" icon. 2. In the "Display Properties" window, click the "Settings" tab and click "Change Display Type". 3.
Service Center EUROPE Country ASC Tel Country ASC Tel U. K Pulse Service Centre Ltd. 44-(0)-870-013-4470 Hungary Profit Service Center Kft. 36 1 399 0405 Germany BITRONICS GmbH 49-3634-683313 Bulgaria RTS 359-2-971-2020 France DATEX 33-1- 69- 310101 SWITZERLANDS TPA PANATLANTIC AG 41 1 886 10 16 Spain FREE ELECTRONICA S.A 34 91 6774787 SLOVAKIA BGS-Distribution a.
