User Manual

ManualsBrandsHansaton Akustik ManualsElectronicseControl

Checking the Battery Status

When the batteries of the remote control are low, this is indicated in

the status bar.

Additionally, you can check the battery status at any time in the menu.

•

To enter the menu, press the volume up button and the volume

down button simultaneously.

•

Navigate to the menu entry

Info

by pressing the volume up button

or the volume down button.

•

Conﬁrm your selection by pressing the program change button.

The battery status is displayed:

battery full battery empty

•

To return to the standard display, press the program change button.

ɳɵɶɷɸ

Program

change button

Key lock switch

Control buttons

Display

Control Buttons

Your Remote Control. Functions. Adjusting Volume.

Changing Hearing Programs.

Volume up/

down buttons

Programming

connection

Remove empty batteries immediately and dispose of them

according to local regulations.

Instructions For Use

See also ”General Warnings and

Safety Instructions“, Page 6-13

More functions are available in the menu. To enter or exit the menu,

press the volume up button and the volume down button simultane-

ously.

All actions initiated with the remote control are immediately reﬂected

on the display. For example, if you press the volume up button, the

following icon is shortly displayed.

The remote control does not receive informa

tion from your hearing systems.

All actions that you initiate with the controls of

your hearing systems are not reﬂected on the

remote control’s display.

You can quickly access two functions

with the control buttons on the right

hand side of the remote control.

The control buttons of the eControl

advanced can be conﬁgured by

your Hearing Care Professional.

Small icons on the display show the

functions.

Power Save Mode

If the remote control is not used for some time, the display automati-

cally turns black. The remote control is then in its power save mode.

•

Press any button to activate the display again.

All other icons: Shortcut to select a preferred hearing program. The

available icons and hearing programs depend on your personal setup.

Indicates change of volume

Program name

Program icon

Program number

Alarm clock is activated

Batteries of the remote control are low

Function of programmable control buttons

Key Lock Switch

•

To prevent any accidental operation while the remote

control is in pockets or bags, move the key lock switch to

lock position (red color visible).

When the key lock is active, all buttons on the

remote control are disabled.

The following icon is displayed.

Programming Connection

This connection is only to be used by your Hearing Care

Professional for programming the remote control.

Batteries.

•

Attach the cover by sliding it onto the remote

control.

The current time setting is displayed.

If you want to change it, refer to section

„Setting the time”.

The remote control uses two

AAA batteries.

Inserting Batteries

•

Slide the battery compartment

cover in the direction of the

arrow.

•

Insert the batteries. Make sure

the „+” symbols on the battery

and compartment are aligned.

Indicates change of hearing

program and volume

Alarm clock is activated

Batteries of the remote control

are low

Function of control buttons

Display eControl Advanced

Display eControl Basic

eControl Basic eControl Advanced

If you are wearing two hearing systems, the volume will be adjusted on

both systems at the same time.

•

Press the volume up button or the volume down button to adjust

the volume by one step.

•

Press the program change button to switch

to the next hearing program.

•

Press the program change button repeat-

edly until the icon of the desired hearing

program is displayed.

Or:

•

Press the control button next to the icon

indicating the desired hearing program. The

control buttons have to be conﬁgured by your

Hearing Care Professional.

eControl Basic

Adjusting the Tinnitus Noiser Level

eControl Advanced

If you are wearing two hearing systems, the hearing program will be

changed on both systems.

This function is only available if your Hearing

Care Professional has conﬁgured the tinnitus

noiser for both your hearing systems and for

the control buttons of the remote control.

You can recognize the setting, if the corre

sponding icons are displayed next to the

control buttons.

•

To adjust the noiser level, press the upper

or the lower control button.

Turn hearing systems on

or off (standby).

Turn hearing systems on

or off (standby).

Reset to default volume

and hearing program.

Reset to default volume

and hearing program.

Tinnitus noiser level up. Tinnitus noiser level up.

Tinnitus noiser level

down.

Tinnitus noiser level

down.

Adjust treble. Adjust treble.

Adjust bass.

Display.

2 3

5 6

eControl

Summary of content (2 pages)

PAGE 1
Your Remote Control. ɳɵɶɷɸ Display eControl Basic 1 Indicates change of hearing Display D Key lock switch GB Programming connection Control buttons P 2 Alarm clock is activated 3 Batteries of the remote control 2 are low Volume up/ down buttons Display. See also ”General Warnings and Safety Instructions“, Page 6-13 GB 3 P Display eControl Advanced press the volume up button and the volume down button simultaneously.
PAGE 2
Distributed in USA by Hansaton Acoustics Inc. 15650 36th Ave N Ste 110 Plymouth, MN 55446 USA Turning your Hearing Systems on and off (mute). Alarm Clock. You have several options to turn your hearing systems on and off with your remote control. Both hearing systems are simultaneously turned on or off. When you turn your hearing systems off via remote control, the following icon is displayed. It is displayed until you turn your hearing systems back on. Additionally, all buttons are disabled.