User's Manual

ManualsBrandsHANK SMART TECH ManualsSmart HomeZigbee Humidity & Temperature Sensor

User Manual

Zigbee Humidity & Temperature Sensor

HKZB-THS01

1. PRODUCT OVERVIEW

The zigbee Humidity & Temperature Sensor is based on Zigbee 3.0 2.4G wireless radio

frequency technology to achieve intelligent detection. It allows to monitor the ambient

temperature and humidity remotely, which all real-time readings can be checked on Android or

IOS APP. And it can also jointly control the other smart devices according to the current

temperature and humidity values.

2. PRODUCT FEATURES

 Inclusion, activation by one click

 LED lights indicates the status of the device during operation: inclusion, exclusion and

activation

 Adopt Zigbee 3.0 protocol, support Zigbee MAC specification

 Powered by 1xCR2032 battery. Ultra-low power consumption, long battery life

 View the real-time ambient temperature and humidity values through the APP at anytime

and anywhere

Summary of content (10 pages)

PAGE 1
User Manual Zigbee Humidity & Temperature Sensor HKZB-THS01 1. PRODUCT OVERVIEW The zigbee Humidity & Temperature Sensor is based on Zigbee 3.0 2.4G wireless radio frequency technology to achieve intelligent detection. It allows to monitor the ambient temperature and humidity remotely, which all real-time readings can be checked on Android or IOS APP. And it can also jointly control the other smart devices according to the current temperature and humidity values. 2.
PAGE 2
   Low battery alert Work as a trigger to activate the other smart devices OTA Supported. 3. PRODUCT STRUCTURE LED Indicator Power button Air Vent Button Activities and LED indicator In the network 1.Long press the button for 5 seconds, Blue LED blinking, the device enter configuration mode. Network access successful, the LED light turns off; Times out LED goes out. 2.Press the button, LED turns on, release it, LED turns off. Out of the network 1.
PAGE 3
Standy current: ≤4.5uA Battery Capacity: 210mAh Protocol: Zigbee Wireless transmitting and receiving frequency 2.400—2.483GHz Network protocol supported IEEE802.15.4 Wireless coverage: Indoor 40m Outdoor 100m Temperature Measurement -20～+60°C（-20℃≤Temperature <10℃ +/- 1.5℃,10℃≤Temperature≤60℃ +/- 0.5℃） -4 ～ +140 ℉ （ -4 ℉ ≤Temperature <50℉ +/- 2.7 ℉ ,50 ℉ ≤Temperature≤140 ℉ +/- 0.9℉） Humidity Examination 0%-99.9%（-20℃≤Temperature<10℃ 15%，10℃≤Temperature≤60℃ +/- +/- 10%） 0%-99.
PAGE 4
5. INSTALLATION （1）Open the back cover by rotating it counterclockwise Back Cover （2）Put the CR2032 battery into the battery slot with battery "﹢" facing up. Align the back cover clamping position, close the cover by rotating clockwise Battery slot （3）Place the product in the environment to be tested 6. APP CONFIGURATION 6.1 Scan the QR code below to download the Android and iOS app. Or download the "smart life" APP from the apple store and Google Play store.
PAGE 5
Android&IOS 6.2 Start the APP and register an account with your phone or email, and then login APP with your account 6.3 Before adding the humidity and temperature sensor, you need to add a Zigbee gateway in the APP.
PAGE 6
.4 Add Devices （1）Click the Zigbee gateway that has been added to the APP, click “Add subdevice”under the gateway list, press and hold the temperature and humidity sensor button for 5 seconds to make the LED indicator blinking quickly, click “LED already blink”in the APP. When the device is searched, the device will be displayed in the APP network interface. Click”Done”, the temperature and humidity sensor can be added to the corresponding Zigbee gateway and displayed in the list.
PAGE 7
（2）After the device is connected to the network, users can rename or share the device. i Note 1. Make sure the Zigbee Gateway and smartphone are on the same network when adding devices (2.4g only) 2. Ensure that the Zigbee gateway is compatible with the added temperature and humidity sensor 7.
PAGE 8
If the battery level is greater than 50% of the current power, the battery will be considered to have been replaced, and a power report will be sent. 8.
PAGE 9
. RESET DEVICE Reset the humidity & temperature sensor from the network: 1) Login the APP and click the device 2) Click the icon in the upper right corner of the device and click "Remove Device" 3) Click "Disconnect and wipe data" and click "confirm" in the pop-up box; 4) After the device is successfully reset, the device will be disappeared from the APP interface and enter configuration mode i Note: “Disconnect and wipe Data” will clear the memory of the temperature and humidity sensor, it means delete
PAGE 10
connected. -- Consult the dealer or an experienced radio/TV technician for help. RF Warning statement: The device has been evaluated to meet general RF exposure statement. The device can be used in portable exposure condition without restriction.