User's Manual

ManualsBrandsHANK ELECTRONICS ManualsElectronicsMultisensor

Multisensor user manual

HKZW-MS08

Multisensor is a universal Z-Wave device. Along with detecting motion the device measures

the temperature, humidity and luminance . It can communicate with associated Z-Wave

devices, such as Siren, Smart Switch, etc.

Multisensor can be included and operated in any Z-Wave network with other Z-Wave

certified devices from other manufacturers and/or other applications. All non-battery

operated nodes within the network will act as repeaters regardless of vendor to increase

reliability of the network.

Multisensor is also a security Z-Wave device and supports the Over The Air (OTA) feature for

the product’s firmware upgrade.

If you want your Multisensor to be a security device that use secure/encrypted message to

communicate in a Z-Wave network, then a security enabled Z-Wave controller is needed.

The features list:

1) Z-Wave Plus certified for wide compatibility (500 serials product).

2) Measure temperature.

3) Measure luminance

4) Measure humidity.

5) Shock sensor.

6) The battery life is up to 2 years (default settings, motion detecting 20 times per day).

7) Low battery alarm.

8) Support firmware OTA.

Ⅰ. Familiarize yourself with your Multisensor

Summary of content (9 pages)

PAGE 1
Multisensor user manual HKZW-MS08 Multisensor is a universal Z-Wave device. Along with detecting motion the device measures the temperature, humidity and luminance . It can communicate with associated Z-Wave devices, such as Siren, Smart Switch, etc. Multisensor can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications.
PAGE 2
1. Multisensor Layout 2.
PAGE 3
Radio frequency: Range: Dimensions: Working current: Standby current: Recommended installation height: PIR detection range  868.42MHz (EU) 908.42MHz (US) More than 100m outdoors About 30m indoors 59*59*56mm ＜100mA ＜40uA 2m Within 8m （ installation height 2m） Ⅱ.
PAGE 4
Ⅲ. DETECTION AREA Multisensor’s motion detection area is shown below. Actual range of the sensor can be influenced by environment conditions. Should false motion alarms be reported, check for any moving objects within the sensor’s detection area, such as trees blowing in the wind, cars passing by, windmills. False motion alarms may be caused by moving masses of air and heat as well.
PAGE 5
Ⅳ. Inclusion to Z-Wave network The sensor can be added to the Z-Wave network by following steps: （1）Power on the device by USB or batteries. （2）Set z-Wave gateway/hub to learning mode (see Z-Wave gateway/hub Operation Manual) （3）Triple click the device's Z-Wave button （4）The LED indicator of the sensor will keep flashing quickly. If the inclusion is successfully connected, the LED light will be off.
PAGE 6
V. Exclusion from Z-Wave network The sensor can be excluded from the Z-Wave network by following steps: （1）Power on the device （2）Set z-Wave gateway/hub to exclusion mode (see Z-Wave gateway/hub Operation Manual) （3）Triple click the device's Z-Wave button （4）The LED indicator of the sensor will keep flashing quickly. If the exclusion is succeeded, the LED light will be flashing slowly (enter the SmartStart function).
PAGE 7
Ⅷ. WAKE UP COMMAND CLASS If the product is within the network, press and hold Z-Wave button for more than 3 seconds，it will broadcast Wake Up Notification when release the button, it will report that the product is waked up. Using Wake up interval set command to set the automatic wake up time. When it’s set to 0~3599，the product will keep sleeping.
PAGE 8
13 (0x0D) 2 30 (1) Wait time for clearing the PIR triggered (default 30 seconds) If there is no trigger during this time, it will send Notification （Notification Type is Home Security， Event is 0，Parameter 1 is Motion Detection Unknown Location）to its associated node.
PAGE 9
183 (0xB7) 2 1 Temperature sensor value change threshold （1）Unit F as default，threshold value=Value. Effective value:1F～144F（0x0001~0x0090.