User's Manual

ManualsBrandsHangzhou Wistar Mechanical & Electric Technology ManualsElectronicsPART 15 REMOTE CONTROL TRANSMITTER

Remote control instruction

WSRC Instruction

Warning

1. Children should be supervised to ensure that they do not play with the appliance.

2. If the supply cord is damaged. It must be replaced by the manufacturer, it’s service agent or similarly qualified person

in order to avoid a hazard.

3. The receiver is high voltage，so put the receiver at the place without water.

4. Be sure the L line(brown) and N line(blue) are correctly connected.

5. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

FCC STATEMENT:

1. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1). The device may not cause harmful interference

2). The device must accept any interference received, including interference that may cause undesired operation

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

1．Characteristic ( The device may not cause harmful interference. The device must accept any interference received,

including interference that may cause undesired operation.)

2．Wires Connect

A Emitter

1.Power:12VNH battery, Model: Gp 23A/27A

2.Protection Index: IP 30

3.Frequency: 433.92MHz

4.Working Current: ≤8mA

Code group: Rolling code

B. Receiver

Power: AC 110V, 60Hz

Rated load: not exceeding 800w

The receiver will cut the electricity after working 4

minutes continuously.

The mainframe can deal with 15 control channels at

most.

Compatible with any type Wistar RF rolling code

emitter

Δ. motor’s up (black )

N. motor’s neutral wire (blue)

▽. motor’s down (brown)

E. motor’s earth wire (yellow and green)

E.receiver’s earth wire (yellow and green)

N. AC 110V N line (blue)

L. AC 110V L line (brown)

COM. hand switch public wire

DOWN. hand switch key Down

STOP. hand switch key Stop

UP. hand switch key UP

Study: learning button

S3,S2,S1: hand switch up, stop, down

Summary of content (4 pages)

PAGE 1
Remote control instruction WSRC Instruction Warning 1. Children should be supervised to ensure that they do not play with the appliance. 2. If the supply cord is damaged. It must be replaced by the manufacturer, it’s service agent or similarly qualified person in order to avoid a hazard. 3. The receiver is high voltage，so put the receiver at the place without water. 4. Be sure the L line(brown) and N line(blue) are correctly connected. 5.
PAGE 2
Remote control instruction 3．Program Enactment Please notice: the short-press mentioned below means press 0.5s, long-press means press 3s, the distance between two press is 1s. all WS series remotes are of similar setting way, if the signal is interfered, please begin again. 1. Code learning: ( there are three ways) Way A a) Short-press the Study button on the receiver, then the motor will vibrate. Which means it is ready to be programmed.
PAGE 3
Remote control instruction 2. Code cleaning Way A. First press the stop button to make the receiver in stop state, then short-press the learning button 3 times b)Short-press the up button once, the motor will vibrate, The code cleaning is successful. 3 times once Way B Long-Press key study till the motor vibrates four times. It means all the code has been cleaned successfully. And all the emitters which has been setted can not control this receiver. 3s 3.
PAGE 4
Remote control instruction Delete point to point function a) First press the stop button to make the motor in stop state, b) Short-press the learning button 2 times. c) Short-press the DOWN button within 10s, the motor will vibrate. once 2 times 5．Malfunction inspect and disposal malfunction disposal method the LED light on the emitter can’t light check the battery of the emitter none reaction check the main power, the connection and the temperature which accord with the technical data.