30 Starting Installation Pairing Sensor The KATVR-Central and the KATVR-Back Sensor can only be used after being paired, and the two KATVR-Foot Sensor can only be used after being paired with the wireless receiver. Pairing of KATVR-Central and KATVR-Back Sensor The KATVR-Central and the KATVR-Back Sensor are paired when the six-digit dialers are dialed to the same position.
31 Starting Installation KATVR-Foot Sensor 1 2 3 4 5 6 Six-digit red dialer Charging port Working indicator - red means that it is not connected with the wireless receiver; blue indicates that it has been connected with the wireless receiver; Charging indicator - red indicates charging; blue indicates that the battery is full, when the foot sensor is not used, turn off the switch to reduce battery charge Switch button 3.
2 Starting Installation Wireless Receiver 1 2 3 Working status indicator - red indicates that it is not connected to two foot sensors or is connected only to one foot sensor; blue indicates that it has been connected with two foot sensors USB A type plug Six-digit red dialer
33 Starting Installation KATVR-Central Sensor 1 2 3 4 Top sensor cable interface USB A type plug Bottom sensor working indicator: red indicates that it is not connected to the back sensor; green indicates that it has been connected to the back-sensor Six-digit red dialer Caution KATVR-Encoder working indicator: red means it is not connected to the KATVR-Back Sensor; blue means it is connected to the KATVR-Back Sensor.
34 Starting Installation KATVR-Back Sensor 1 Working status indicator 3 Red switch button 2 Charging status indicator 4 Micro USB charging interface 5 Six-digit red dialer Caution Red indicator: when it is on, it means the power supply to the KATVR-Back Sensor is normal but it is not connected to the KATVR-Central. Green indicator: when it is on, it means the KATVR-Back Sensor is connected to the KATVR-Central Sensor. 1.
35 Starting Installation Power Switch Upon confirming the proper installation and connection of the product, press the power button for all the devices a.Check if the controllers are fully charged. You may check the controllers' battery charge level while not running any program or upon opening the main control panel of the system. When the battery charge level is insufficient, the indicator will display a red dot. Use the accessory power adapter and the USB data cable to charge each controller.
36 Starting Installation Sensor Status Indicators Location Indicator KATVR-Central Sensor Working indicator Wireless receiver Working indicator KATVR-Foot Sensor Red KATVR-Central Sensor normal power supply, not connected to the back sensor Wireless receiver normal power supply, not connected to the KATVR-Foot Sensor Working indicator KATVR-Foot Sensor normal power supply, not connected to the wireless receiver Charging Indicator Being charged Blue KATVR-Central Sensor normal power supply, co
37 Starting Installation Correct Wearing Steps of getting on the Device 1.The user sits in the chair, put on KAT SHOES by himself/herself and steps on the pedals. 2.The user holds safety handrails, carefully enters the treadmill base plate, and turns his/her back to the treadmill. The working staff must accompany the user upon entrance to ensure personal safety. 3.The staff help to fasten the girdle set. 4.The staff help user to wear the. 5.
38 Starting Installation Installation and Dismantling of KAT Foot Sensors on KAT SHOE COVER Fast Replacement of KATVR-Foot Sensor A fast replacement module has been designed in the s tructure of the foot sensor f or an easier replacement of foot sensor on the shoe cover. The replacement can be done in fast way through the turning of the foot main body and the buckle.
39 Starting Installation Installation and Dismantling of Foot Sensors on KAT SHOES Installation of KATVR-Foot Sensor: Insert the buckle of the KATVR-Foot Sensor into the external elastic belt of the Shoes and make sure the two sides of the buckle are inserted into the belt respectively, as shown in the figure: Installation of the Main Body of KATVR-Foot Sensor: Fix the main body of the KATVR-Foot Sensor to the buckle, as shown in the figure: Turn the main body of the KATVR-Foot Sensor clockwise and if yo
40 Starting to Use Installing the KATVR-Foot Sensor: Insert the buckle of the KATVR-Foot Sensor into the external elastic belt of the Shoes and make sure the two sides of the buckle are inserted into the belt respectively, as shown in the figure: Dismantling the Main Body of KATVR-Foot Sensor: Turn the KATVR-Foot Sensor counter-clockwise and pull it out.
41 Starting to Use Instructions for Using KAT WALK Self-Adaption Computer If you want to use your own computer, please make sure it meets the following hardware requirements: CPU: Intel Core i5-4590 or higher. Memory: 8GB or higher. Graphics card: Geforce GTX 1070 equivalent or higher. Hard disk space: at least 200GB available on the system partition. Screen resolution: 1920x1080 or higher.
42 Starting to Use Login the KAT Game Flat 1.Double click the KAT entertainment platform icon and type in the username and password to log into the platform. 2. Enter the platform page, where the left side shows the category of games and the QR code of the Company, and the user may choose the game based on his/her preference.
43 Starting to Use 2. Select the game and click“Enter details”to view the introduction of the game for more details. If the game is not installed to the computer yet, please click“Install”on the right side of the interface to install the game. While downloading and installing games is free of charge, a certain number of K coins will be consumed when playing the game.
44 Starting to Use Game Settings How to Enter the Game Settings Page On the right side of the main interface, the gears area is the button to access game settings. The administrator may set up the game by entering the page of game settings. KAT will preset the parameters for the game software and please do not change them randomly. If there is any problem, please contact the KAT service center for advice. Open the game platform software and click the gear on the right to enter the page for the settings.
45 Starting to Use Click the“Error detection”at the lower left corner of the page, and the button will change to“Detecting”, and the sensor data will appear in the text box.
46 Starting to Use Calibration Settings 1. Place the HTC VIVE head-mounted display (Not included with this version, it needs to be purchased separately) above the girdle set, and make sure the orientations of the display front, the girdle opening and the KAT WALK are consistent. 2. Make sure the letters HTC on the head-mounted display is along the very middle of the girdle set (as shown in the picture), make it horizontal and start the software“calibration”.
47 Starting to Use 3. After the completion of“Calibration”,keep the head-mounted display, the girdle and the KAT WALK PREMIUM facing the same direction and start to set the room mode. 4. Click the Steam VR on the upper left corner of Steam testing software, and the menu will turn up. Click the top “Run Room Setup” Ready 5. Select the mode“Stand Only” 6.
48 Starting to Use 7. Click“Calibration Central Point” 8. Click“Next”after finishing calibration 9.
49 Starting to Use 10. The room setup is done and click“done” Attention: 1.Make sure the front of the head-mounted display, the girdle set opening and KAT WALK are facing the same direction during the setup. 2.Please do not move KAT WALK or the base station after the setup.
50 Starting to Use Setting the Static Value 1.After the calibration, the static value needs to be set up for the user. 2.An user with a height of 150-190cm and a weight of no more than 100KG will need to wear the whole leg and girdle set first, and then stands upright in the SPACE. Click the icon for static in the software and it will show successful setting of static; the value will be defined as the static value.
51 Starting to Use Quitting the Game 1.Turing off during Click the“ Close”button at the upper right corner of the page to turn off the game. Click“Quit”at the upper right corner of the page and it will prompt a box requesting you to confirm whether to quit the game. Click“Confirm”to quit the game and“Cancel”to continue the game.
52 Starting to Use Turning Off the Software Click“ Close”at the upper right corner of the page and it will prompt a box requesting the input of the password. Key in the password and click“ Confirm”to turn off the software.
53 Help Center Help Center The Help button is located on the upper right part of the page. Click it to enter the self-help repair service page under the technical support on the KAT official website. You may view the introduction of the game and the videos and texts for common operations in this page.
54 Help Center Click the drop-down box for the“ Introduction of the game”and you will see the list for all the games on the platform. Choose a game and you will be able to view the basic introduction and the instructions of the game. Click the drop-down box for the“ Videos of Installation and Use”and you will see the videos and texts for the installation and daily use. Select an operation and you will be able to view the corresponding video and text.
55 Dismantling and Replacement Dismantling and Replacement of KAT WALK PREMIUM Component For your safety Please make sure all the power is off prior to dismantling. Dismantling Shell 1.Remove the pedals and unscrew all the screws on the base plate shell; carefully dismantle the light source cable of the base plate to separate the shell. 2.Unscrew all the screws on the side and back of the lower part of the support pillar to separate the shell of that part. 3.
56 Dismantling and Replacement Attention 1.Make sure all the power is off and that all the power connections are cut off prior to the dismantling. 2.As the device is very heavy, it requires at least three male adults to do the dismantling. 3.Please do follow the above procedures to do the dismantling for safety purposes. 4.Please properly keep all the items dismantled, including screws, cotter pins, etc. 5.As the internal wires are fragile, please do not forcibly dismantle.
57 Dismantling and Replacement 2.As the groove that holds the sole slider expands, the old slider can be easily taken off 3. Take off the old slider and use the same method to embed a 4.Relax KAT SHOES and the sole groove will return to normal; then the new slider automatically fits into the groove and the replacement is done.
58 Dismantling and Replacement Procedures of Replacing Wheels 1.Turn the sole of KAT SHOES up 2.Use the accessory wheel replacement tools to pry the wheel 3.Take out the old wheel and replace with a new one to finish the replacement Caution 1.As the wheel replacement tools are quite sharp, please do not use too much force when replacing the wheels to ensure the safety of related personnel and the completeness of the groove. 2.
59 Dismantling and Replacement Instructions for Replacing KAT SHOE COVER It is advised to replace the slide block at the sole of the KAT SHOE COVER when it is loose or cannot roll properly. Steps of Replacing Slide Blocks 1. One hand holds the Cover, while the other pinches the slide block. Then bend the block outwards with strength. 2. Take the damaged block off the Cover. 3. Take out the new block.
60 Dismantling and Replacement 4. One hand holds the Cover, while the other press the block into the block slot. Caution Make sure the orientations of the block upper and lower surface are consistent with those of other blocks when pressing it. 5. Complete the block replacement.
61 FAQ Unable to Walk or Walk Slowly in the Game Cause: The DLL files are not installed Solution;Choose settings ->add dlls of the game platform login screen.On the pop up window, double click the bat file to install dlls. Cause: Incorrect connection of KATVR-Foot Sensor Solution: If the working indicator on the KATVR-Foot Sensor is red, check if its six-digit dialer value is consistent with that of the wireless receiver. If not, switch off the foot sensor, re-dial it, then switch on.
62 FAQ Inconsistent Walking Orientation Between Figures in the Game and in the Reality Cause: The calibration is not done Solution: Complete the calibration by following the steps on page 44 of the User Manual. Cause: The base station or the equipment is moved Solution: Redo the calibration by following the steps on page 44 of the User Manual.
63 FAQ Unable to Download the Game Cause: Network connection error Solution: Check if the network connection is normal Cause: Insufficient storage of the C drive Solution: Check the remaining space of the C drive. If it is small, clean up the drive. Cause: Error in the game download Solution: Enter the windows->downloadgame file to find the corresponding game file. Manually delete the file, download and install the game once again on the KAT entertainment platform.
64 FAQ The Blue Indicator of the KATVR-Central Is Not On Cause: The KATVR-Back Sensor is not power on Solution: Check if the KATVR-Back Sensor is power on. Plug the cable out of and into the power socket of the KATVR-Back Sensor . Observe if the blue indicator turns on.
65 Warnings FCC Warnings This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
66 Warnings IC Warnings This device complies with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.