User's Manual

User Manual
Zigbee Temperature&humidity
sensor
DSBC-060-2
Product Introduction
Directions For Installation
Screw fixing type
3M adhesive type
Attention
Product Overview
Power On/Off
Product Function
DSBC-060-2 is an outdoor temperature and humidity Zigbee
sensor, Suitable for outdoor environment temperature and
humidity detection. It has excellent function of ultra-low power
consumption, a red LED lamp and a button switch (low power
setting, pairing setting).
Power On :Press button for 3 seconds to start up in the Power
off state, the indicator LED will be flash 3 times (f=1Hz).
Power Off: Press button for 15 seconds to power off in the
Power on state, the indicator LED will be flash 5 times (f=2Hz).
Pair
1.In the power on state ,press the button to enter the pairing
mode, and it can pair to gateway or mobile phone to config the
beacon parameter
2.In this state, the red LED will flash in 1Hz ,and the product
can be search and pair.
1.Drill holes （3mm） in the corresponding positions of the wall,
and plug the expansion screw cap into the hole；
2.Place the bracket in the corresponding position and fix it with
screws;
1: Select the adhesive tape to stick to the back of the device,
and tear off the adhesive tape on the back of the beacon
sensor;
2：Just stick the beacon sensor to the surface of the object;
1.Being close to a metal object will interfere with the signal,
causing the signal to be weaken.
2.Note the distance between DSBC-060-2 and the receiver to
guarantee the accuracy of receiving.
3.Keep away from the corrosive objects.
4.When installing, make sure that the sensor part is installed
facing down.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation
is subject to the
following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation
This device has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This device generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications.
OTA
The product support OTA function, that the gateway and device
management platform have been bound, sensor terminal device
and gateway have been paired successfully.
Upload OTA firmware to platform, the platform issues upgrade
instructions to the specified sensor terminals, the gateway
downloads and verifies OTA firmware and saves it locally. Then
sensor terminals send query whether have OTA firmware to the
gateway every 6 hours (or power off the sensor terminal and
then on, it will sends query whether have OTA firmware to the
gateway within 5 minutes ). If the gateway has the relevant OTA
firmware, the sensor start the OTA.
Low voltage indication
When the battery level is lower than 30%, the product will enter
the low battery mode, the LED light will flash per 10s, and the
gateway can also obtain the product’s battery information from
the data packet
Product Specification
Product
Name
Model
No.
Battery
Capacity
Product
Size
Protocol
Beacon sensor
950mAh
50.5*50.5*16.5mm
Zigbee 3.0
DSBC-060-2
100m
65g
0~100％
-30~65°C
Temp
Humidity
Distance
Weight
3M
3M
3M
3M
3M
3M
back
Button Main body
Indicator LED
However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause harmful
interference to radio or television reception, which can be
determined by turning the device off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the device and receiver.
--Connect the device into an outlet on a circuit different from that
to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for
help
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment