Installation Instructions
Use
r
Bluetooth
e
D
S
OTA
The product support OTA function
battery, to enter OTA mode, the L
E
When in the OTA mode, gateway
o
the OTA.
Low voltage indica
t
When the battery level is lower th
mode, the LED light will flash per
product’s battery information fro
m
FCC Warning Stat
e
This device complies with Part 15 of the FC
C
following two conditions: (1) this device may
(2) this device must accept any interference
operation
This device has been tested and found to co
Part 15 of the FCC Rules. These limits are d
interference in a residential installation. This
energy and, if not installed and used in acco
r
to radio communications.
However, there is no guarantee that interfer
e
does cause harmful interference to radio or
t
device off and on, the user is encouraged to
measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the devic
e
--Connect the device into an outlet on a circ
u
--Consult the dealer or an experienced radio
/
Changes or modifications not expressly app
r
user's authority to operate the equipment
r
Manual
e
mergenc
y
button
S
BC-110-1
, Press and hold the button and insert the
E
D will be always on, and it will last 60s.
o
r mobile phone can pair the product and s
t
t
ion
an 20%, the product will enter the low batt
e
10s, and the gateway can also obtain the
m
the data packet.
e
ment
C
Rules. Operation is subject to the
not cause harmful interference, and
received, including interference that may cause undesire
d
mply with the limits for a Class B digital device, pursuan
t
t
esigned to provide reasonable protection against harmful
device generates, uses and can radiate radio frequency
r
dance with the instructions, may cause harmful interfere
n
e
nce will not occur in a particular installation. If this device
t
elevision reception, which can be determined by turning t
h
try to correct the interference by one or more of the follo
w
e
and receiver.
u
it different from that to which the receiver is connected.
/
TV technician for help
r
oved by the party responsible for compliance could void t
Product In
DSBC-110 is Is a
k
one button for pre
s
used with Dusun
G
emergency alarm
s
Product S
p
t
art
e
ry
d
t
o
n
ce
h
e
w
ing
he
Directions
Keyfob
With metal ring access
o
backpacks
Wristband
With rubber wristband
a
Keyfob
Product
Name
E
m
Protocol
Battery
Capacity
Product
Size
troduction
k
eyfob/wristband emergency butto
n
s
s in case of emergency ,The prod
u
G
ateway, and then users can recei
v
s
ignals from anywhere through the
p
ecification
For Installation
o
ries, the product can be hung on key rings,
a
ccessories, can be wear the product on the
Wristba
n
Bluetooth
m
ergenc
y
button
Model
No.
D
S
Bluetooth 5.2
Temp
-
1
Humidity
0
225mAh
Distance
5
Φ41mm
Weight
n
, it have
u
ct can be
v
e
cloud.
Prod
u
LE
D
badges,
wrist
n
d
3Madh
e
1: Select the
adhesive tap
e
2:Just stick
S
BC-110-1
1
0~65°C
0
~100%
5
0~100m
30g
ct Overvie
w
D
e
sive
adhesive tape to stick to the back of the de
v
e
on the back of the beacon ;
the beacon to the surface of the object;
3M
3M
3M
3M
3M
3M
Button
P
Pa
i
1.
W
to
e
(d
u
2.
A
off.
th
e
3.
I
f
sta
an
d
fre
q
th
e
v
ice, and tear off the
D
1:
T
Re
p
A
1.
B
to
b
2.
N
ac
c
3.
K
4.
W
P
roduct Function
ir
W
hen there is no pairing information, press
a
e
nter the pairing mode, and the LED starts
t
u
ty = 0.5);
A
fter the pairing is successful, the LED stay
s
If fail to pair successful within 60 seconds ,
e
pairing mode.
f
have pairing information, after pressing th
e
rts to flash at a frequency of 1Hz (duty=0.5
)
d
press the button again within 2s, and hold
q
uency of 2Hz (duty=0.5), the pairing is cle
a
e
button is not pressed again within 2s, the
L
D
irections For Batte
r
T
urn counterclockwise to open the produc
t
2
p
lace the battery, the battery model is CR2
0
A
ttention
B
eing close to a metal object will interfere wi
t
b
e weaken.
N
ote the distance between DSBC-100-1 and
c
uracy of receiving.
K
eep away from the corrosive objects.
W
hen installing, make sure that the sensor p
a
nd hold the button for 5 seconds
t
o flash at a frequency of 1 Hz
s
on for 2 seconds and then goes
The LED light turns off and exits
e
button for 5 seconds, the LED
)
. At this time, release the button.
for 5s, the LED flashes at a
a
red and the pairing broadcast . If
L
ED will stop flashing.
ry
Replace
2
:
0
32
t
h the signal, causing the signal
the receiver to guarantee the
art is installed facing down.