Installation Instructions

ManualsBrandsHangzhou LMenergysolution lighting ManualsElectronicsBluetooth module

LMenergy LMIC Lighting Controller

The LMenergysolution Lighting Company, Ltd, LMIC Lighting Controller is a Bluetooth based mesh system

for controlling on/off and 0-10VDC dimming of LED products. The system consists of a Transmitter

(includes an onboard motion sensor) and a Receiver. The Receiver is connected to the light. An optional

part of the system is an Ambient Light Sensor (ALS) that is required if 0-10VDC dimming control is

desired. An iPhone app is used to controller the LMIC. Each device is a node, nodes form a mesh.

The LMIC is activated when the Transmitter’s motion sensor receives a motion signal which causes the

transmitter to calculate an action according to the user's settings. The Transmitter then transmits the

associated action to the Receiver by Bluetooth. The Light Sensor is connected to the Receiver. In this

configuration, the Receiver outputs 0-10V control voltage to the light to achieve the set brightness.

LMIC Lighting Control Process

1. Create Lighting Control Plan

a. Identify Control Groups - Building/Areas

b. Identify Control Subgroups - Areas/Rooms

c. Identify needed devices

i. Transmitters (T) - motion sensors

ii. Receivers (R) - light fixture controllers and ambient sensors

2. Download LMIC app and create an account

3. Configure/Provision installed LMIC devices that are listed in the Unconfigured Device tab

4. Create Groups and Subgroups in the app

5. Populate Subgroups with installed LMIC devices listed in the Ungrouped Device tab

6. Set Subgroup control parameters

a. If needed, set individual device control parameters

Group

Subgroup

Transmitter

(Motion

Sensor)

Receiver connected to a light

Summary of content (21 pages)

PAGE 1
LMenergy LMIC Lighting Controller The LMenergysolution Lighting Company, Ltd, LMIC Lighting Controller is a Bluetooth based mesh system for controlling on/off and 0-10VDC dimming of LED products. The system consists of a Transmitter (includes an onboard motion sensor) and a Receiver. The Receiver is connected to the light. An optional part of the system is an Ambient Light Sensor (ALS) that is required if 0-10VDC dimming control is desired. An iPhone app is used to controller the LMIC.
PAGE 2
LMIC Account Setup     Download LMIC app from the iPhone App Store. Create an account using the “Register” link. Password reset is though the “Forgot Password” link. A device (Transmitter or Receiver) can be controlled by only one account.
PAGE 3
Getting Started  Touch “Add Devices” to find the Unconfigured devices that are available to Configured/Provisioned.
PAGE 4
Configuring/Provisioning Devices When power is applied to installed Transmitters (T) and Receivers (R) will initially show up in the Device’s page under the Unconfigured tab. A device is either a Transmitter (motion sensor) or a Receiver (light controller with ambient sensor). If power is applied to a Transmitter (T) or Receiver (R), the device will be displayed in the “Unconfigured” tab. If a installed device is not listed in the Unconfigured tab, check the power connection to the devise.
PAGE 5
Configuring/Provisioning Devices  Touch “Start Provision”.
PAGE 6
Configuring Devices   When this screen appears, the selected device will begin to flash. o A Receiver (R) will cause the connected light to flash. o A Transmitter (T) will cause the blue light inside of the motion sensor to flash. After confirming the identity of the intended device, touch “Start Provision”.
PAGE 7
Set Device - Transmitter Save  The device name can be edited.  The Motion Sensor and other settings will be addressed in the Set Parameters section.  Touch “Save” to confirm the configuration - this needs to be changed to “Save”  Find Me - For Transmitters, the motion sensor light will flash. For Receivers the LED light will flash.  Delete Device - the device will reset to the Unconfigured condition and displayed in the Device Page Unconfigured tab.
PAGE 8
Set Devices - Receiver  The device name can be edited.  Setting parameters will be addressed in the Set Parameters section.  Touch “Save”” to confirm the configuration.  Touch “< Back” to get back to the Unconfigured page.
PAGE 9
Configured Devices - Ungrouped Devices that were Configured/Provisioned will be displayed on the Device page in the Ungrouped tab. ● Select the Ungrouped devices that you want and copy them to a subgroup you set up.  Ungrouped Receiver (R) devices may be programmed according to the Set Parameters section (as individual - stand alone devices).  Ungrouped Transmitters may be programmed according to the Set Parameters section but will not communicate with Receivers until included in a Subgroup.
PAGE 10
Adding Groups  Add a Group by touching the + sign in the top right corner of the screen.
PAGE 11
Add a Subgroup  Touch the Group name to add a Subgroup.  Additional Subgroups may be added by touching the + in the upper right corner of the screen.
PAGE 12
Add Devices to the Subgroup  Touch the Subgroup name to add devices.  12 Touch Add Devices.
PAGE 13
Add Devices to the Subgroup - Ungrouped Tab ●  Select the devices that you want to add to the subgroup Touch “Copy To” 13
PAGE 14
Reviewing with the Group/Subgroup/Devices Touch 1 SubGroup to see the Subgrou Touch 1 LMenergy Demo 1 to see grouped devices 14
PAGE 15
Set and Edit Group Settings  15 Swipe left to edit Group Name
PAGE 16
Set and Edit Subgroup Parameters  16 Swipe left to edit Subgroup parameters
PAGE 17
Set Subgroup Parameters Subgroup name may be edited Subgroup lights may be turned On and Off Set value represents the percentage of total available lumens that will be used when Power is turned On. Value should be set based on desired foot candles measured in undimmed lights. Initial Brightness value will be used to determine the percentage of Brightness calculated for Motion Detected, On - Subgroup controls will account for ambient light. LMIC will hold with 10% of set brightness.
PAGE 18
Set Device Parameters  18 Swipe left to edit a device parameter
PAGE 19
Set Device Parameters - Transmitter with Motion Sensor Subgroup setting are mirrored in all devices. Changing a device setting will only affect the individual device, not the entire subgroup. If there is only Transmitter in the subgroup, a change will affect all devices. Device name may be edited On - Light output is based on Motion Detected, No Motion and Additional Time set parameters.
PAGE 20
Set Device Parameters - Receiver (with Optional Timer Settings)  The device name can be edited.   Switch - Lights can be turned on and off. Brightness - Overrides Subgroup parameter. Set device light level as a percentage of available lumens/watts.  Ambient Sensor - Overrides Subgroup parameters. Set brightness is maintained when ambient light changes  On/Off Timer - Allows for up to 10 On or Off parameters to be set for a 24-hour period.
PAGE 21
If the ambient light sensor off is selected, the brightness percentage only indicates that the brightness opening of the light is independent of the ambient light. When the ambient light sensor is selected, the brightness accuracy will be kept at ± 10% LX. Each time the power is turned on to a Receiver, the R will self-calibrate for about 25 seconds.