Keypad User Manual LCD Keypad User Manual 1
Keypad User Manual About this Manual This Manual is applicable to LCD keypad. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website (http://overseas.hikvision.com/en/).
Keypad User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Keypad User Manual or dispose of it at designated collection points. For more information see: www.recyclethis.info. 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).
Keypad User Manual Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. The precaution measure is divided into ‘Warnings’ and ‘Cautions’: Warnings: Serious injury or death may be caused if any of these warnings are neglected. Cautions: Injury or equipment damage may be caused if any of these cautions are neglected.
Keypad User Manual Cautions: Make sure the power supply voltage is correct before using the product. Do not drop the product or subject it to physical shock. Do not install the product on vibratory surface or places. Do not expose it to high electromagnetic radiating environment. Do not aim the lens at the strong light such as sun or incandescent lamp. The strong light can cause fatal damage to the product.
Content Chapter 1 Introduction _____________________________________8 1.1 Overview _______________________________________________ 8 1.2 Appearance Description ____________________________________ 8 1.3 Keypad Beeper and Indicator_______________________________ 10 Chapter 2 Installation and Wiring ___________________________13 2.1 Wiring Connector Description ______________________________ 13 2.2 Keypad Address Settings __________________________________ 13 2.
Keypad User Manual Chapter 1 Introduction 1.1 Overview DS-PK00/PK00M/-LCD/LED series LCD/LED alarm keypad are used for connecting to the security control panel. It implements operations on the security control panel through programming and prompts alarm with the indicators and audio alert. 1.
Keypad User Manual No.
Keypad User Manual 1.3 Keypad Beeper and Indicator Beeper Description No. Sound Prompt Description 1 One Beep Pressing keys prompt; The command is timed out or the command is too long. 2 Two Beeps Valid command. completed. 3 Five Beeps Invalid command. Failed to upload the report in 60s. 4 Continuous Beeping For Two Seconds Fault Prompt 5 Slowly Continuous Beeps Entry/Exit Delay 6 Rapidly Continuous Beeps Entry/Exit Delay, less than 10s.
Keypad User Manual Indicator Description Status Working Status Indicator Working Status Indicator Normal Solid Green System Fault Solid Red Power Working Status Indicator Power On Solid Green Working Status Indicator Working Status Indicator Partition Perimeter Disarmed OFF Partition System Perimeter Armed Orange Working Status Indicator Working Status Indicator Partition Armed Solid Red Partition System Disarmed Solid Green Password Modifying Flicking Green Fob Code Matching
Keypad User Manual LED Zone Indicator Zone Working Status Indicator Working Status Indicator Normal OFF Fault Solid Red Alarm Flicking Red Bypass Solid Green Zone Indicator under Engineering Mode (The corresponding zone indicator light will turn orange when operating): No. Description No.
Keypad User Manual Chapter 2 Installation and Wiring 2.1 Wiring Connector Description No. 1 2 3 4 Description Loud Speaker Tamper-Proof Switch Wiring Connector DlP Switch 2.2 Keypad Address Settings An address is required for each alarm keypad in the system. These addresses cannot be repeated. Once exchanging the alarm keypad, the address of the new keypad must be the same as the replaced one. You should configure the address via DIP switch of the keypad before powering on the system.
Keypad User Manual Keyboard Address ON DIP Keyboard Address ON 1 2 3 4 5 1 2 3 4 5 00 01 02 03 04 05 06 07 ■ ■ ■■ ■ ■ ■■ ■■■ ■ Keyboard Address ON DIP 08 09 10 11 12 13 14 15 DIP Keyboard Address ON 1 2 3 4 5 ■ ■ ■ ■ ■■ ■ ■■ ■ ■■ ■■■ ■■■■ 16 17 18 19 20 21 22 23 ■ ■ ■ ■■ ■ ■ ■■ ■■■ ■ ■ ■ ■ ■ ■ ■ ■ ■ DIP 1 2 3 4 5 24 25 26 27 28 29 30 31 ■■ ■■ ■ ■■ ■■ ■■ ■■■ ■ ■■■ ■■■■ ■■■■■ ■ 2.
Keypad User Manual 3. Connect the corresponding cables. 4. Push the keypad body in the mounting plate from bottom up. 5. Fasten the keypad body with the three buckles on the plate. 6. Align the screw holes with the screws on the bottom of both keypad and mounting plate. 7. Tighten the screws to fix the keypad on the mounting plate and complete the installation. 2.4 Keypad Wiring The keypad wiring is shown as follows. Chapter 3 Keypad Operation (Local Operation) 3.
Keypad User Manual Function Description Command Arming/Disarming Normal(Away)Arming/Disarming 【Password】 【#】 Instant Arming 【Password】 【*】 【7】 【#】 Stay Arming 【Password】 【*】 【4】 【#】 Normal (Away)Arming/Disarming 【Password】 【Bypass】 【#】 Mandatory 【Password】 【*】 【7】 【Bypass】【#】 Mandatory Instant Arming 【Password】 【*】 【4】 【Bypass】【#】 Bypass Zone(n) 【Password】 【Bypass】 【n】 【n】 【n】 【#】 Bypass 【Bypass】 【n】 【n】 【n】 【#】 nnn is the zone No.
Keypad User Manual Device Status Query System Fault Status Wireless Settings Pairing User 【Status】 and 【Password】 【*】 【91】 【No.】【#】 Deleting the Specified Connected 【Password】 【*】 【90】 【No.】【#】 Wireless Device Control Panel Wireless Device Deleting all the Connected 【Password】 【*】 【92】 【#】 Wireless Device Card User Settings Pairing Card No. and Control 【Operator】 【Project】 【10】 【User No.】 【#】 Panel 【Operator】 【Project】 【11】 【Card No.