Hamaton Tire Pressure Monitoring System User’s Guide HTRD 01 HANGZHOU HAMATON TYRE VALVES CO., LTD No.12 East Zhenxing Road Linping, Yuhang District, Hangzhou, China Tel: 0571-89361286 Fax: 0571-89361285 Web: www.hamanton.com.
Content General .........................................................................................................................1 Product View and Parts Information..............................................................................2 Installation of Sensor..................................................................................................3-5 Installation of Receiving Display....................................................................................6 System Settings.
General Product View and Parts Information Tire Pressure Monitoring System is referred to as TPMS. System introduction Solar Panel TOP TPMS is composed by four sensors (five sensors if monitoring for spare tire is necessary) and one receiving display. Sensors are installed inside the tires. They will collect real-time temperature and pressure data of the tires and send the data to the receiving display in wireless way. Meanwhile, the receiving display will accordingly receive the information.
Installation of Sensor * Professional tire installation and maintenance equipment is required for the sensors of the system. Therefore, it is suggested that you go to professional tire shops for installation. STEP 1 Successively dismantle the tire, screw out the valve core of tire valve and make the tire deflated. STEP 2 Loosen outer surface of the tire toward to the tire valve with tire changer and then loosen the inner surface of the tire. Strip the tire from the wheel frame.
Installation of Sensor STEP 7 Blow up the tire, so as to make the pressure of the tire reach to standard pressure value. The standard pressure value of each vehicle is generally pasted on the place under door frame in driver's side or on fuel tank cap. As well, you can reference to the user's manual. For the remoulded car, it is required to confirm standard tire pressure value by tire shop. STEP 8 Dynamic balance is done for well-charged tire.
System Settings System Settings Standard pressure setting STEP 2: setting standard pressure * Firstly, make sure the separate standard pressures of front and rear wheels (standard pressure is generally marked on the place under door frame in driver's side or on fuel tank cap. As well, you can reference to the operating instruction). 1. Press "OK" key to enter the main menu.
System Settings System Settings Temperature unit setting Time display setting * There are two kinds of temperature units for the receiving display of Hamaton TPMS, which are separately centigrade (°C) and Fahrenheit (°F). The factory setting is °C. The customer can select in accordance their habits. 1. Press "OK" key to enter the main menu; 2. Press "SEL" key to select the option of "temperature unit setting"; 3. Press "OK" key to enter the submenu of "temperature unit setting"; 4.
Positioning Settings of Sensor * While newly installing the sensors, it is required to separately install them into the corresponding tires in accordance with "left front", "right front", "left rear" and "right rear" marked on the sensors. In case of changes in position of tires or exchanges of sensors, it is required to again carry out positioning settings on sensors in four tires. Positioning Settings of Sensor 7.
Settings of Spare Tire Real-time Monitoring Display * If the spare tire is equipped with sensor, it is required to carry out settings on the sensor inside the spare tire. The display screen will circularly display the current tire positions and its realtime monitoring data in accordance with sequence of left front, right front, right rear and left rear, as well as the tire pressure and tire temperature. TEMPERATURE UNIT SETTING DISPLAY TIME SETTING SENSOR SETTING 1.
High Tire Pressure Alarm LEFT FRONT High Pressure 3.4 Bar 26 °C When the tire pressure is 30% higher than the setting pressure value, it will give high tire pressure alarm. The alarm station is the same as that of the low tire pressure alarm set forth. The interface will show high pressure. Alarm will be free until the pressure return back to the standard tire pressure scope. RESOLUTION: The high tire pressure is caused by the high road temperature in summer and long-time driving.
Alarm on Low Sensor Voltage LEFT FRONT Low Electricity Quantity of Battery Battery installed in the tire and used for sensor is unchangeable, which is able to be used for 5-7 years under the normal condition. When the electric quantity of the battery is gonging to be exhausted, the transmission signal will fade. At this time, it will give an alarm on low sensor voltage and give a prompt that the driver shall change sensor.
Terms on After-sale Service for Hamaton TPMS Product The consumer shall buy Hamaton TPMS product via legal channels. The consumer enjoys the after service of Hangzhou Hamaton tire Valves Co., Ltd for any fault due to accident beyond control. I In order to protect the legal right and interest of the consumer, the consumer is asked to pay attention to the following information 1.
Maintenance record for Hamaton TPMS Maintenance record for Hamaton TPMS * The table shall be filled in by the maintenance technician * The table shall be filled in by the maintenance technician Maintenance Record Three Maintenance Record One TPMS model: Maintenance date: Maintenance date: TPMS model: Name of the maintenance unit: Name of the maintenance unit: Address and telephone of the maintenance unit: Address and telephone of the maintenance unit: Detailed description on fault: Detailed de
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.