Operation Manual of Beyondfire Wireless Ignition System ★Please read this manual carefully before use. ★This manual contains a warranty card. Please keep it properly. Hunan Beyondfire Technologies Co.,Ltd.
1.The System The wireless ignition system for fireworks of “Beyondfire”[Trade Name] consists of mobile devices, FireMaster, FirePoint and ignition heads. 2.Specification & Parameters ● The effective communication distance between “FireMaster” and “FirePoint” is from 50 meters to a maximum distance in an open ground / water surface without obstruction is 400 meters. ● “Mobile Device [Mobile Phone or Tablet] to the FireMaster” is 10 meters.
. Mobile APP Visit www.beyondfire.com, then download and install Beyondfire APP on Android™ or Apple® devices. The APP needs to be enabled: bluetooth, location, storage read and write rights. For operation instructions of the Beyondfire application, please refer to the "?" help document on the upper right corner of the main screen on APP. For more information, visit www.beyondfire.com. 4.
① Unit Carries an “External 2.4g Antenna”. ② Comunciation light Mobile device communication working indicator light.After starting up, it will be always on. When the APP is connected successfully, it will enter a slow flash state. ③ Power indicator light Stays in red mode after starting up. When the battery power is low, it flashes to remind you to replace the batteries. ④ 2 digital display module ⑤ Indicator light of “Lock Switch” and also indicator light of ignition “Safety Switch”.
. Panel Function Description of FirePoint [Receiver] ①External 2.4g antenna. ②③④Corresponding to the 1-2-3 state indicator light of ignition channel.If the ignition head is not connected or the heating wire of the ignition head is damaged, the lights will not be on. When the ignition head is connected, the light turns green, while in the state of ignition, it turns red. ⑤POWER button.Long press 2 seconds to start up, while short press to shut down.
. Installation of FUSE to “The Ignition Head” [Crocodile Clip] Place the green lead in the ignition clip and try your best to put the lead end in the center of the heater. Note: ◆ After each ignition, the hot wire will adhere to the carbide and residue generated by fuse combustion.Use a fine brush to clean the residue on the heating plate, otherwise it may affect the next ignition.
.App operation steps 8.Restore of System 1) FirePoint: Within 15 seconds after starting up, long press the power button for 2 seconds, and the three green lights of the ignition head are in flashing state. Please press the power button again within 5 seconds, and the green lights will flash out in turn in order of 3-2-1, then the factory settings are restored successfully.
9.Troubleshooting Problem Reason Solution Fail to start up 1.Incorrect installation of battery polarity 2.Low power of batteries 1.Remove the batteries and install the battery compartment with correct polarity. 2.Replace new batteries Power light flashes after power on 1.Low power of batteries 2.Wireless module's failure to read data 1.Replace new batteries 2.Restore the factory settings, and reset the address according to the initial address modification steps.
Safety Tips: 1) This product should pay attention to moisture-proof, water-proof, and the safety distance from fireworks should be controlled at more than 2 feet, which is prohibited burning and suitable for personal consumption. 2) This product contains sharp parts and high temperature heating parts, please avoid accidental injury caused by the wrong operation of minors. Notes: 1) This product uses 1.5V AA alkaline batteries. Please do not leave it outside for a long time in low temperature.
★Any of the following circumstances shall not be within the scope of warranty service: 1 improper handling, use, management, maintenance to damage, or artificial damage; 2 The product is disassembled, modified or repaired without authorization; 3 Damage caused by external causes (lightning, power supply, etc.); 4 The damage caused by incorrect installation or use of the user; Products that do not belong to the warranty scope will be charged for maintenance services.