ALGIZ RT10 MANUAL www.handheldgroup.
FEDERAL COMMUNICATIONS COMMISSION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. IEEE 802.11b or 802.11g operation of this product is firmware‐limited to channels 1 through 11.
RF exposure warning A separation distance of 10mm shall be maintained from the Human body in normal use. RF exposure information (SAR) This Rugged Tablet PC meets the government's requirements for exposure to radio waves. This Rugged Tablet PCis designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.
Table of Contents Table of Contents5 1.888 2.888 2.1999 2.1.1 Barcode Scanner13 2.1.1414 2.1.3 Physical Layout14 3.171717 3.1 SIM Card Insertion17 3.2 SD Card Insertion18 3.3 Charging the Device18 4.191919 4.1 Power ON19 4.2 Audio Volume19 4.3 2020 4.4 2020 4.4.1 2121 4.5 2121 4.6 Lock Screen22 4.7 Quick Settings23 4.7.1.232323 4.7.2.232323 4.7.3.232323 4.7.4.242424 4.7.5.242424 4.7.6.242424 4.7.7.242424 4.7.8.242424 4.7.9.242424 4.7.10.242424 4.8 Send a SMS24 4.9 2424 4.10252525 4.11252525 4.12252525 4.
4.15252525 4.16252525 4.17252525 5262626 5262626 5.1.1272727 5.1.2303030 5.1.3313131 5.1.4323232 5.1.5333333 5.1.6353535 5.1.7353535 5.1.8353535 5.2363636 5.2.1363636 5.2.2414141 5.2.3414141 5.2.4414141 5.2.5414141 5.2.6424242 5.2.7424242 5.3434343 5.4444444 5.5454545 5.5.1464646 5.5.2464646 5.5.3464646 5.5.4 Wallpaper46 5.5.5474747 5.6494949 5.7494949 5.7.1505050 5.7.2515151 5.7.3525252 5.8535353 5.8.1535353 5.8.2535353 5.9535353 Version 1.
5.9545454 5.10545454 5.11555555 5.11.1555555 5.11.2555555 5.11.3565656 5.11.4565656 5.11.5565656 5.11.6575757 5.11.7585858 5.12595959 6.595959 6.1 Internal Storage59 6.2606060 6.3606060 7616161 7.1616161 7.2616161 7.3616161 7.4616161 7.5616161 7.6616161 7.7616161 8626262 8.1626262 8.2626262 8.2.1626262 8.2.2646464 9.646464 9.1656565 106666666666 11676767 12676767 Version 1.
1. INTRODUCTION This guide covers the Algiz RT10 tablet, and optional accessories. The Algiz RT10 is a rugged tablet, designed for use by field personnel in demanding conditions. It integrates best ‐ in‐class connectivity with efficient computing and multimedia features. The tablet runs Android Pie 9 operating system, and comes pre‐installed with many Google applications, including Google Play. NOTE: The images in this guide may slightly differ from the actual screens that you see in the device. 2.
2.1 Device Specification The base specifications of the Algiz RT10 tablet are below: Parameters Description Processor Snapdragon 820 CPU (APQ8096 SOC) 64‐bit Quad Kryo core Adreno 530 3D Graphics @624MHz OS Android Pie 9 Application Compatibility 64 bit and 32 bit applications are supported Display 10.1” TFT display High‐brightness (600 nits) Touch Panel 10 point capacitive touch panel Chemically strengthened glass 10.
Connections Sensors Audio Haptic Feedback Accessibility Input Devices Battery 1 x USB 2.0 port 1 X RJ45 for Ethernet 10/100/1000 LAN 1 x USB 3.
The Algiz RT10 is available as four SKUs: ALGIZRT10‐B‐EU This model supports the LTE bands prevalent in the European Union ALGIZRT10‐B‐EU‐BC Equivalent to the ALGIZRT10‐EU, with the barcode scanner module This model supports the LTE bands prevalent in the North American region ALGIZRT10‐B‐NA TABLE 2.1. LTE BAND SUPPORT NA Model GSM 850 and GSM1900 (GSM900 and GSM1800 roaming) UMTS B2, B4, B5 (B1 and B8 roaming) LTE B2, B4, B5, B13, B17 (B1 and B8 roaming) TABLE 2.1.
2.1.1 Barcode Scanner The Barcode scanner module is designed with support for 2D‐Imager N6603 from Honeywell. Detailed specifications are below: Scanner Engine Version 1.
Sensor Proprietary CMOS sensor with global shutter Imager Resolution 844 x 640 pixels Field of View Horizontal 42.4° degree, Vertical 33° degree Skew Tolerance +‐ 60 degrees Pitch Tolerance +‐ 45 degrees Roll Tolerance +‐ 360 degrees Focal Distance From front of engine: 7.64 in Aiming LED 610nm Green Linear LED Illumination LED 610nm White LED Input Voltage 3.3 VDC ± 5% TABLE 2.2.
USB cable Battery pack Quick Start Guide For best performance, we strongly recommend that you use only the supplied charger with this tablet. 2.1.3 Physical Layout Front Panel The front side of the device, shown in figure 2.1. “Front panel” is where the user interacts with the device.
Diagram – Figure 2.1 front panel Back Panel The back panel (shown in figure 2.2, “Back panel”) include the following items. Flash LED Rear Camera Rear Dock Speaker Mic Battery Pack Diagram – FIGURE 2.2. BACK PANEL Version 1.
Left Side Panel The left panel is shown in figure 2.3, “Left side Panel”. FIGURE 2.3. LEFT SIDE PANEL Right Side Panel The Right Panel of the device, shown in figure 2.4, “Right Side Panel” port cluster with below listed ports: Ethernet port USB A port TYPE C USB port HDMI port FIGURE 2.4, RIGHT SIDE PANEL Top Panel The device is configured with the optional barcode scanner module that can be seen on the Top panel. The top side of the device is shown in figure 2.
3. DEVICE SETUP 3.1 SIM Card Insertion ALGIZ RT10 Tablet support Single Nano SIM card. The SIM Card Slot are on Back side of the Tablet as shown in Figure 3.1, "SIM Card Slots". To insert the card: 1. Power OFF the tablet 2. Place the tablet on flat surface, with the screen facing down 3. Remove the battery pack 4. Insert the SIM Card You can see more details about inserted SIM cards in Device Setup. Se ngs → Networks & Internet → SIM cards Version 1.
3.2 SD Card Insertion This tablet supports a single micro SD card for secondary storage. SD card slot is on back side of tablet, under the battery cover as shown in figure 3.2, “SD Card Slot”. Once SD card is inserted successfully, you can check its details in ‐ Se ngs → Storage → SD card 3.3 Charging the Device We recommend that you fully charge the battery prior to first use. A high power USB port is provided; we recommend that this is used to charge the device.
4. BASIC USAGE INSTRUCTIONS The Algiz RT10 runs Android Pie 9. The Algiz RT10 is packed with the same features you would expect in a feature‐rich tablet/smartphone. The device provides the intuitive Android user interface with no modifications. If you are already familiar with any Android device, then you will feel right at home using this device. The Algiz RT10 can be used in all screen orientations.
FIGURE 4.2. HOME SCREEN Version 1.
4.4.1 Navigation Bar At the bottom of the screen, you will find the Navigation Bar with three soft buttons. The three buttons, in order are: The “Back Button” touching this generally takes you to the previous screen. The exact behavior may depend on the active application The “Home Button” touching this takes you to the home screen The "Recent Apps Button” touching this shows you the running applications. You may directly switch to another application by touching on it 1. 2. 3. 4.
4.7 Quick Settings Common Settings may be quickly access using "Quick Settings". To access Quick Settings, simply swipe down from the top of the screen. From Quick Settings see figure4.5, “ Quick Settings”, you may change the screen brightness, connect to Wi‐Fi networks, Bluetooth devices and SIM networks, as well as control automatic screen rotations and other options. FIGURE 4.5. QUICK SETTINGS 4.7.1. Adjusting Screen Brightness In Quick Settings, drag the slider to set the screen brightness. 4.7.2.
4.7.4. Do not disturb The “Do not disturb” tile allows you to control your phone's notifications. Tap on this tab and you will turn on Do not disturb and enter a menu allowing you to customize how undisturbed you want to be. 1. Total silence: Nothing will interrupt you 2. Alarms only: Any alarms you have set can disturb you 3. Priority only: Alarms can get through, but you can customize exactly what else should and shouldn’t disturb you 4.7.5. Airplane Mode Airplane mode disables all radios.
4.10 Configure Google Account A Google account is required for making the most use of many applications installed on the device. If you did not configure a Google account on startup, then you can add one from Settings | Accounts. 4.11 Useful Applications The ALGIZ RT10 ships with many useful applications. Please see Section “5.6 Applications”. 4.12 Install Applications Please use the Google Play application to install applications from the Google Play store.
If you are planning to associate another Google account with the device after factory reset, then it is highly recommended that you remove the Google account before issuing the factory reset. 5. SETTINGS The Settings application can be used to connect to various networks, as well as configure the wide variety of options available. The Settings applications may be accessed from the application screen. Swiping down the screen and touching on the settings icon is a faster way to reach there.
FIGURE 5.1. NETWORK & INTERNET SETTINGS 5.1.1 Wi‐ Fi To perform Wi‐Fi related settings select the "Wi‐Fi" option under Network & Internet option in settings as shown in FIGURE 5.2, “Wi‐Fi SETTINGS”. When the tablet is powered ON for the first time Wi‐Fi will be OFF as shown in FIGURE, “WI‐FI OFF”. To connect to Wi‐Fi network: 1. Turn ON Wi‐Fi 2. Select a network from available list of networks shown in FIGURE 5.4, “AVAILABLE WI‐FI NETWORKS” 3.
Turn on Wi‐FI automatically ‐> Wi‐Fi will turn back on near high‐quality saved networks, like your home network 2. Open network notifications ‐> Notify when a high‐quality public network is available. 3. Install Certificate ‐> Install Network certificates 4. Wi‐FI Direct ‐> allows you to connect to other devices 5. Mac address ‐> show you the MAC address of your Tablets Wi‐Fi network adapter 6. IP Address ‐> show you the current IP address for your Wi‐Fi connection 5.1.2 Mobile Network 1.
5.1.3 Data Usage Data Usage shows the complete data used by the devices. By tapping on Data Usage under network and internet shows Data used by different networks such as Data used by Mobile, Data Used by Wi‐fi network, Data used by Ethernet. See FIGURE 5.9. Data usage Settings. FIGURE 5.9. Data usage Settings Version 1.
5.1.4 HotSpot & tethering Hotspot and Tethering is used to Provide Internet to other devices through your mobile data connection. Hotspot & Tethering includes FIGURE 5.10. HOTSPOT & TETHERING SETTINGS USB Tethering ‐> You can share your Tablets Mobile data to other devices via USB Tethering Wi‐FI Hotspot‐> You can share your Tablets Mobile data to other devices via Wi‐Fi Hotspot You Can set up wifi hotspot by giving the network name, security (None, WPA2 PSK), password and by selecting the AP Band (2.
5.1.5 Ethernet To connect to an Ethernet network, use the "Ethernet" option under Wireless & networks settings. The "Enable Ethernet" option shown in FIGURE 5.12. ETHERNET OPTIONS allows you to turn ON or turn OFF the Ethernet connection as needed. To Enable Ethernet you have to Reboot the Tablet. Figure 5.12 Ethernet Options FIGURE 5.
Network Selection Policy The data networks on the tablet in order of priority are • Ethernet (highest) • Wi‐Fi • SIM based networks (lowest) Only one data network may be active on the tablet at a time. When a connection to any network of higher priority is available, then the lower priority networks are disabled automatically. As an example, when Wi‐Fi is enabled, it takes priority over 2G/3G/4G networks. Similarly when an Ethernet connection is established, it takes precedence over all other networks. 5.
5.2 Connected Devices You can use device settings to set device properties such as Bluetooth, NFC, Android Beam, USB, Barcode, etc. 5.2.1 Bluetooth Bluetooth related settings are under the "Bluetooth" option under "Connected Devices" Settings, in connection Preferences as shown in FIGURE 5.16. BLUETOOTH SETTINGS. FIGURE 5.16. BLUETOOTH SETTINGS Version 1.
When the tablet is powered ON for the first time Bluetooth will be OFF as shown in FIGURE 5.17.BLUETOOTH OFF. FIGURE 5.17. BLUETOOTH OFF Prior to using a Bluetooth device, you need to pair the device with the tablet, as follows: 1. Turn on Bluetooth 2. Select the devices from “Available device” list as shown in FIGURE 5.18. AVAILABLE DEVICE LIST 3. Touch “Pair” on Bluetooth pairing request as shown in FIGURE 5.19.
FIGURE 5.20. PAIRED DEVICE LIST Configurable Bluetooth Power Class The Bluetooth interface on the Algiz RT10 may be configured to run at two power levels: Class 2 operation. This is the default, and provides a short range of operation Class 1 operation. This is a high power mode, providing a longer range of operation NOTE: To make effective use of the higher power, both devices must operate in Class 1. FIGURE 5.22.
FIGURE 5.23. SELECT POWER CLASS 5.2.2 NFC & Android Beam Near Field Communication technology is used to communicate between devices that are a few centimeters away from each other. NFC & Android Beam must be turned on for sharing between devices to work correctly. You can use NFC (Near Field Communication) to exchange data when your tablet touches another device. To exchange data using NFC: 5.2.
5.3 Apps & Notifications By using Apps settings you can view and manage applications. Here you can view all the applications installed in your tablet. To view category vise like Downloaded, On SD card, running scroll from right to left. You can do following operations on a selected application as shown in FIGURE 5.25.
5.5 Display The "Display" option under Device settings allows you to set below display properties for your tablet shown in FIGURE 5.28. DISPLAY SETTINGS. FIGURE 5.28. DISPLAY SETTINGS 5.5.1 Brightness level Adjust the slider to set the brightness level see FIGURE 5.29. BRIGHTNESS SETTINGS. FIGURE 5.29. BRIGHTNESS SETTINGS 5.5.2 Night Light Night light tints your screen amber. This makes it easier to lock your screen or read in dim light and may help you fall asleep more easily. 5.5.
5.5.5 Sleep This sets the idle timeout after which the device goes to sleep. You may set a value between 15 seconds and 30 minutes as shown in FIGURE 5.30. “SLEEP TIME OPTIONS”. The “never” setting may be used when you do not want the screen to go to sleep automatically. This is typically used for benchmarking the device. Using this option can drain the battery faster than normal. If very long operation times are required, then we recommend that you keep the charger connected. FIGURE 5.30.
5.5.7 Screen Saver To control what happens when the phone is docked and/or sleeping. You can set clock, colors, and photo frame or photo table as daydream. Using menu you can specify when to daydream (while docked, while charging or either. 5.5.8 Ambient Display Tablet screen wakes up when Notification arrives. 5.5.9 Device theme Select the Device theme as Automatic (Based on wallpaper) or Light and Dark Device theme. 5.5.10 Touch Mode Select the Touch Modes as Hand/Rain or Glove/Pen Mode. Version 1.
5.6 Sounds This option allows you to control below sound and notification properties for your tablet (shown in FIGURE 5.31. SOUND SETTINGS) Media volume ‐ to set volume for media file such as videos, audio songs etc.
5.7.1 Internal Storage It displays total space allowed to store under internal storage, currently available space and list of all applications using internal storage with space used as shown in FIGURE 5.32. INTERNAL STORAGE SETTINGS FIGURE 5.32. INTERNAL STORAGE SETTINGS Version 1.
5.7.2 SD Card It displays total space allowed to use, currently available space in SD card.Eject SD card to unmount the SD card before removing it, to avoid data loss. Format SD card ‐ to remove all the data stored in the SD card. FIGURE 5.33. SDCARD STORAGE SETTINGS Version 1.
5.7.3 USB Storage It displays total space allowed to use, currently available space in USB storage. Eject USB storage ‐ to unmount the USB device before removing it, to avoid data loss. Format USB storage ‐ to remove all the data stored in the USB. FIGURE 5.34. USB STORAGE SETTINGS Version 1.
5.8 Security & location 5.8.
5.9 Accessibility The accessibility settings allows you to do following operations: Barcode Scanner services Select to speak Talk Back Text to speech conversion Set Font Size Set Display Size Enable magnification gesture Large Mouse Pointer Invert the color Enable Auto‐rotate screen Configure Hotkeys Text to speech conversion Set delay for touch & hold Combine Channels when Playing Audio Set high Contrast text 5.
5.11 System System settings allows you to set system properties such as Language, date & time, Reset etc. as shown in FIGURE 5.37. SYSTEM SETTINGS FIGURE 5.37. SYSTEM SETTINGS 5.11.
storage including Google account, system and app data and settings, downloaded apps and other user data Version 1.
5.11.6 About Tablet You can see the following information about your tablet in this option as shown in Figure 5.
5.11.7 User Configurable Hotkeys The Algiz RT10 includes two user configurable hotkeys. Each hotkey can be configured for the following functions: Android Back Key Android Home Key Launch an Application Deactivated Hotkey configurations is access from the Settings application, under "Accessibility". Each hotkeys can be configured independently, as shown in FIGURE 5.40. HOTKEY CONFIGURATION.
If you go to Se ngs → Storage → Internal storage it shows the details such as total space allowed, available space and space used by different applications as shown in FIGURE 5.26, “INTERNAL STORAGE SETTINGS”. To view the data stored under internal storage use the File Explorer app. When you connect the tablet to computer, you can see a drive named "Internal storage". If you click the drive, it displays different folders contains the categorized data. 6.
7 INPUT 7.1 Touch Screen The touch‐screen features an anti‐glare coating. Ten point Multi touch is supported. Common gestures like pinch‐zoom can be used. Supports Rain, Glove and Pen Mode. 7.2 Changing the Touchscreen modes The tablet’s advanced capacitive touchscreen has 3 built‐in operating modes, for users to choose under different usage scenarios: Mode 7.3 Usage Scenario Hand/Rain Mode The Hand/Rain mode is the default operating mode of the touchscreen.
8 COMMUNICATION 8.1 Ethernet 100/1G Ethernet port on the device allows you to connect to Ethernet. The Ethernet port is located on the right side of the device, in the port cluster shown in figure 8.1, “Ethernet Port”. Insert The Ethernet cable as shown in figure 8.2, Ethernet Cable Insertion. To enable Ethernet and set static IP see SECTION 5.1.4, “ETHERNET”. NOTE: It is recommended to use Ethernet cables with length less than 3 meters. Figure 8.1. ETHERNET PORT FIGURE 8.2.
Bluetooth file transfer To transfer a file to paired device using Bluetooth: Turn ON Bluetooth Select the file Touch the Bluetooth icon Select the device to transfer file Once the connection is successful, it starts transferring the file. You can see the file sending notification on screen. If the file transfer is successful, you can see the file listed under outbound transfers shown in FIGURE 8.3, “BLUETOOTH OUTBOUND TRANSFERS” by touching the notification.
8.2.2 Wi‐ Fi This tablet supports Wi‐Fi 802.11 b/g/n. To use any available Wi‐Fi network, setup Wi‐Fi as shown in Section “Wifi”. Sometimes, you may want to know the MAC address of the Wi‐Fi interface. This is available from Se ngs → System → About Tablet → Status → Wi‐Fi MAC address 9. LOCATION Location may use Sources like GPS, Wifi, mobile networks and sensors to help estimate your device location.
The barcode scanner supports a variety of symbologies: 1D, 2D and Postal codes. User may restrict the barcode symbologies that are decoded from Section, 5.2.5,”Barcode”. Version 1.
11 USB A dedicated A‐type USB host port is available on the device. The following types of USB devices may be connected to it. USB storage devices like disk drives & pen drives USB keyboard or USB mouse The user need to connect the USB peripherals through USB host port in right side panel shown in Figure 12.1,”USB Host Port”. FIGURE 12.1. USB HOST PORT Once USB peripheral is connected, the user needs to enable the USB host mode to use USB peripherals.
