Installation and Operating Instructions

ManualsBrandsHanchett Entry Systems ManualsElectronicsAperio V3 Wireless Reader

Page 1 of 10

For more information visit website assaabloyesh.com P/N: 3080006.015_1

Product Specifications

Wireless Frequency: 2.4GHz, IEEE 802.15.4, using AES 128-bit encryption

Lock Battery Type: AA Lithium, 1.5 Volts (V)

Battery Life: 50,000 cycles*

*All battery life claims are approximate and based on a set configuration profile. Battery performance is based on pre-defined system settings such

as battery chemistry and battery model used, credential presentation settings (LED/buzzer), UHF polling period, UHF status intervals, and

operations per day. Actual battery performance will vary and depends on the factors above.

Operating Temperature: 32° to 122° F (0° to 50° C)

HID

multiCLASS SE

technology Credentials Supported:

 High Frequency (13.56 MHz):

 HID iCLASS

 HID iCLASS SE

(SIO-enabled)

 HID iCLASS

Seos

™

 HID MIFARE

 HID DESfire

EV1 SE

 MIFARE CLASSIC

 DESfire

EV1

 Low Frequency (125 kHz):

 HID Prox

, AWID, EM4102, ioProx

AA Lithium Batteries

required. Use of other types of

batteries, such as Alkaline,

will significantly decrease

battery life.

HES R100 Aperio



Wireless Card Reader

Installation and Operating Instructions

Summary of content (10 pages)

PAGE 1
HES R100 Aperio Wireless Card Reader Installation and Operating Instructions 2x AA Lithium Batteries required. Use of other types of batteries, such as Alkaline, will significantly decrease battery life. Product Specifications Wireless Frequency: 2.4GHz, IEEE 802.15.4, using AES 128-bit encryption Lock Battery Type: AA Lithium, 1.5 Volts (V) Battery Life: 50,000 cycles* *All battery life claims are approximate and based on a set configuration profile.
PAGE 2
 NFC/BLE-enabled Mobile Phones Recommended tools Level Pencil, Wax Pencil Clamp Package Contents Reader Torx T8 4-40 x 1/4" Security Screw Backplate Torx T8 Driver Security Bit Page 2 of 10 For more information visit website assaabloyesh.com Alcohol Swab VHB Tape 2X AA Lithium Batteries P/N: 3080006.
PAGE 3
For Technical Support Please call 1-800-810-WIRE Mounting the Back Plate 1. Level and mark the desired placement. Clean the mounting surface with provided alcohol swab. Remove cover from backplate. 2. Cut the VHB tape into two pieces and apply tape as shown. Mount backplate to marked location and apply pressure to activate tape adhesive. Apply VHB Tape to backplate in these locations. Apply pressure for at least 1 minute. Page 3 of 10 For more information visit website assaabloyesh.com P/N: 3080006.
PAGE 4
Note: VHB tape is intended to be used on glass and non-porous metal surfaces. For all other surfaces, use an appropriate adhesive and follow the manufacturer's instructions. Finishing the Installation 1. Install batteries. 2. Secure reader to backplate. Note: Ensure reader is fully seated against the backplate and the screw hole is properly aligned before securing. Micro USB Port Page 4 of 10 For more information visit website assaabloyesh.com P/N: 3080006.
PAGE 5
For emergency power & local (hard wired) firmware updates, use micro USB port located on the side of the R100 reader. LED Codes Page 5 of 10 For more information visit website assaabloyesh.com P/N: 3080006.
PAGE 6
Aperio Hub Technical Data - AH20 Approvals Safety and emissions Dimensions CE, ETL, FCC, IC, C-Tick FCC 47CFR Part 15 subpart B and subpart C; IC RSS-210 EN ETSI 301 489-17 v2.1.1; ENETSI 300 328 v1.7.1; EN 60950-1 ed.2 2007 82x82x37 Page 6 of 10 For more information visit website assaabloyesh.com P/N: 3080006.
PAGE 7
Power Supply Current 8-24 VDC 250 mA minimum Internal Antenna 2 cross polarized dipoles External Antenna (Part No. EXT-10ANT) One reverse polarity SMA external antenna connector. Optional antenna type dipole with max antenna gain of 3.9dBi IEEE 802.15.4(2.
PAGE 8
Note: The Green LED input is used to grant access to the cabinet lock. If the Green LED signal is not available to indicate approved access, the approval input can be activated by a relay with “NO” attached to Green LED and “C” to GND. The Red LED input is used to indicate access denied. If the RED LED signal is not connected, the lock will flash RED three times when a non-approved card is presented indicating loss of connection to the hub rather than access denied.
PAGE 9
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. Conformité aux normes FCC Cet équipement a été testé et trouvé conforme aux limites pour un dispositif numérique de classe B, conformément à la Partie 15 des règlements de la FCC.
PAGE 10
Page 10 of 10 For more information visit website assaabloyesh.com P/N: 3080006.