User's Guide

ManualsBrandsHanchett Entry Systems ManualsElectronicsKS100-640-SE Aperio Server Lock

KS100-640 Aperio

Cabinet Lock Series

Installation Instructions

HES, Inc.

Phoenix, AZ

1.800.626.7590

www.hesinnovations.com

Package Contents

Recommended Tools

Approved RFID Credential

Phillips P2 driver, RJ45 cable

PoE power injector (48VDC)

Optional Additional Tools:

Gang box to mount hub

SFIC Core for key override

Optional Additional Tools:

Normally Open DPS switches

Product Specifications

Wireless Frequency: 2.4 GHz, IEEE 802.15.4, using AES 128bit encryption

Hub Power Requirement: 8-24VDC, 250mA

Lock Power: 48VDC Power over Ethernet (PoE) 802.3af compliant

Operating Temperature: -10C to 50C

Holding Force: 250 lbs

FCC Part 15, Compliant, Industry Canada Compliant

BHMA: A156.3, A156.36, A156.25 Compliant

Credentials Supported: 125kHz Proximity or 13.56MHz iCLASS, iCLASS SEOS, iCLASS SE, ISO1443B UID, Mifare, Mifare Plus,

Desfire SE, Desfire EV1, and NFC credentials are supported depending on lock model.

For technical support please call 1-800-626-7590

Handling

Selector

Lock

Handle

Mounting

Plate

Mounting Screws

Cams (x3)

DPS Cable

SFIC

Cam

Summary of content (8 pages)

PAGE 1
KS100-640 Aperio Cabinet Lock Series Installation Instructions HES, Inc. Phoenix, AZ 1.800.626.7590 www.hesinnovations.
PAGE 2
System Overview The KS100-640 wireless server cabinet lock extends access control to a server cabinet without the complexity and expense of running wires. The KS100-640 cabinet lock connects to an access control system through the included communication hub. The communication hub connects to the access control system with Wiegand wiring typical of a Wiegand reader. When a credential card is presented to the reader on the lock, the request for access is sent wirelessly to the communication hub.
PAGE 3
1. Installing an SFIC Core A key override (SFIC) provides a backup entry method in the rare case the KS100 or access control system is inactive. We recommend this option. The included SFIC cam has been tested with Medeco and Sargent 6- or 7-pin SFIC cores. 6-pin 7-pin 1. Remove plug from handle 2. Insert cam into SFIC Use the included spacers with 6-pin SFICs. 3. Insert SFIC into lock 2. Prepare the Rack Locate the 25mm x 150mm lock cutout on the door, some doors may require modification. 1.
PAGE 4
3. Installing the lock on the door 1. Slide lock into cutout. 2. Plug 48V PoE RJ-45 cable into lock. Lock will beep once and perform self test. 3. Optional: The DPS signal is closed when the handle is resting in its locked position. The DPS circuit can be extended to include normally open DPS switches arranged in a series to monitor additional doors and panels.
PAGE 5
4. Installing the Handing Selector Note: Be careful not to insert/snap the handle all the way in as the lever will lock. Door edge 1. Insert handing selector into lock. 2. Position the arrows to point toward the door edge as shown above. 3. Secure cam with screw. Part Number 3080006.008 Rev. A ©2013, HES, Inc.
PAGE 8
WARNING FCC Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.